This master's thesis deals with design of universal data logging device. The work proposes the design of device architecture and describes individual systems and components, that are necessary for data logging. Logger is designed as a mobile device, with ARM microcontroller at its core. Thesis specifies requirements for device in terms of performance and versatility. The device uses modular construction, as it comprises multiple PCBs. The thesis describes their design and also design of the mechanical construction of data logger. Designed device has been realized and assembled. Software design for microcontroller is also part of the thesis. In the last part, measurements to determine achieved parameters of the device are conducted.

This thesis treats concept of autonomous temperature, relative humidity and pressure USB datalogger. Also there is explained datalogger function, hardware design with respect on device consumption and design of chassis. Furthermore, there is described communication protocol for control and reading out data by the PC. Furthermore, there are described firmware drivers for some used components and modules for USB communication, RTC and data compression. Lastly there is described software which is used for datalogger configuration and data read out.

Thesis deals with Datalogger with Ethernet interface controlled by DISCOVERY Kit STM32F429. Datalogger is equipped with eight digital inputs and three analogue inputs. The measured data are saved on the SD card. The Ethernet interface module is designed using LAN8720A from Microchip.

Thesis discusses bearings failure detection that is manifesting with increased levels of vibration and acoustic emission. The first part of my work gives introduction to common disorders arising on bearings during operation and negative effects on the bearing condition. Further the thesis makes the reader familiar with the terms of vibration and acoustic emission. The work includes a description of available methods for signal evaluation of vibration and acoustic emissions in order to diagnose the state of the bearings in the domains of time and frequency. In the practical part is explained the vibrodiagnostic concept with focus on bearing endurance test. Part of this practical test is a balance sheet for hardware with marginal parametres and a software description. The work is complemented with sorted database of processed topics from the magazine Orbit Bentley Nevada.

This thesis is focussed on designing of the air drop labradory for testing the balistic recovery systems. The first part of the thesis describes balistic recovery systems, their parts as well as methods of testing this devices. In the second charter there is a description of older vision of a testing device and simple test with the electronics of the testing device. The next step is designing of the new koncept of testing device and the structure analysis of the frame. The product of the thesis is a modular automated testing device, which is able to test balistic recovery systems for aicrafts with the weights between 230 and 1700 kilograms.

Målet med undersökningen har varit att undersöka möjligheten att ta fram en kostnadseffektiv lösning för att mäta flöden i slutna rörsystem. Anledningen till att kontaktlösa metoder valts för arbetet är dess egen-skaper att kunna installeras utan att göra ingrepp i ledningarna eller på något sätt påverka det flödande mediet i dessa. Utrustning skall inhand-las och testas i fält. I underökningen ingår det även att ta fram en lämplig metod för att trådlöst överföra insamlat mätdata till valfri IT-miljö och där kunna presentera mätdata på ett översiktligt sätt i ett övervaknings-system samt använda mätdatat till olika statistiska beräkningar. Det hu-vudsakliga applikationsområdet som undersöks är läckageindikering i dricksvattenledningsnät. Anledningen till detta är att många kommuner inte har råd att investera i dyr mätutrustning för övervakning och för dem kan det vara intressant med ett billigt system som är relativt enkelt att installera och implementera i deras befintliga övervakningssystem. Re-sultat av en enkätundersökning som gjorts i samband med undersök-ningen har visat att intresset är stort hos kommunerna, men den visar även att övervakning av vattenledningsnäten med vissa traditionella me-toder kommer att bli svårare i framtiden i och med den stigande andelen plaströr i ledningsnäten. Fälttester av inköpt mätutrustning visar att den skulle kunna implementeras och fungera som flödesövervakning i led-ningsnät. Även fast dess mätnoggrannhet var under det förväntade så vi-sade utrustningen på god linjäritet. / The aim of the survey has been to investigate the possibilities of using a cost-effective solution for measuring flows in closed pipes. Non-intrusive measuring methods are chosen because it’s able to install them without interfering the flow in- or alter- the pipe in any way. Equipment will be purchased and field tested during the time of the survey. The survey also includes investigating suitable methods for wirelessly transmitting col-lected data to an IT-environment, and using measurement data for sur-veillance purposes and various statistical calculations. The main applica-tion area investigated is leakage indication in drinking water pipeline net-works, the reason being that many municipalities can’t afford to invest in expensive measuring equipment and they may be interested in an inex-pensive system that is relatively easy to install and implement in their existing monitoring system. The results of a poll conducted in connection with the survey have shown that there is considerable interest among the municipalities, but it also shows that monitoring of the water supply net-works with traditional methods may become more difficult in the future, the main reason for this seems to be the increasing amount of plastic pipe-lines in the pipeline networks. Field tests of the purchased equipment show that it may be suitable to implement as flow measuring device with the purpose of leakage monitoring, even though its measurement accu-racy was below expected it still shows good linearity.

In the thesis the design of the Data Storage System (DSS) is proposed with the respect to the V-Model methodology. The design is based on users requirements, from which the system requirements are created and the technical specification of the DSS is developed. In the technical specifications the functionality of the DMM and HMI DSS subsystems are described and sub-system requirements are assigned to them, then they are subdivided and assigned to individual DMM (Data memory module) and HMI hardware items. Moreover, requirements are analyzed on hardware items, specific electronic components, are selected and implemented into the block design of the DMM hardware. Based on the block design of hardware, the hardware of the DMM subsystem is designed, selectively simulated and implemented along with the printed circuit board. On the implemented hardware of the DMM subsystems measurements are performed in order to verify the basic functionality of the hardware and the calculated, assimilated and measured values are compared as well. At the end of the thesis there is a short description of the implementation of the software design and its use for basic initialization of the selected processor, together with the verification of its basic function - measuring the frequency of the internal clock sources and the clock domains. The work is completed by sending a message of defined parameters to the selected communication line and sapling it by an oscilloscope, so that the basic function of the DMM subsystem is verified.

The thesis is aimed on construction of solar panel powered datalogger of environmental values. The thesis begins by research of commercial dataloggers. Then the concept of datalogger was created. Then the electronics of datalogger was designed. Datalogger is built as a system driven by microcontroller. The microcontroller reads data from sensors, writes data to memory card and sends data to Czech radiocommunications cloud by LoRa technology. Then the data are resend to MySQL database. Program for microcontroller was made in C language. Configuration of datalogger is done through USB interface by PC application which was created in C# language. For visualisation of measured data ASP.NET Core application was created.

The aim of this thesis is to perform an analysis of possibilities and benefits of installing the Smart Water Metering technology at campus of Faculty of Civil Engineering, Brno University of Technology. The main goal was to provide specific solutions of Smart Metering systems from different companies. One part of this thesis is dedicated to a detailed analysis of a water consumption measurement campaign that took place at the beginning of this academic year using dataloggers. Real-time flow rate and consumed volume was recorded every five minutes. Therefore it was possible to determine water consumption patterns during the day and also tell the minimum, maximum and average flow rate in different parts of the campus. Thanks to these measurements, irregular water consumption during the night was observed. This would not have been easily detected without recording real-time data. This system of recording real-time flow rates with dataloggers is considered to be suitable for the needs of faculty. Thanks to a GSM module, recorded values are sent to an FTP server once a day. From there the data can be downloaded to any kind of analysis software. Installation of Smart Water Metering technology at campus of Faculty of Civil Engineering would be beneficial for both operation of the water supply network and also for purposes of an academic research.

This master’s thesis deals with the design of autonomous monitoring system electronics which will be used for diagnostics of the electromagnetic vibration generator developed at Brno University of Technology. This generator should be used in a practical application where frequent mechanical shocks are present, for example in vehicle or goods transportation. For such an application, the goal of the monitoring system is to find out whether generator is capable of producing enough electrical energy for smooth operation of wireless sensors used in similar applications. The first part of the thesis consists of the autonomous diagnostics system overview from both commercial and scientific spheres, brief description of the vibration generator used and also a summary of commercially available power management electronics. The next chapters present the detailed description of each functional element of energy harvesting system, the simulation of generator’s behaviour for optimal load in three different model applications and the most important part – design of the autonomous monitoring system. In the end, achieved results are evaluated and it is considered whether the shock-driven generator is suitable for use in a given application.