Yes / CDW-based concrete requires alkali-activators to generate geopolymerization process. These alkali-activators are difficult to be handled at the construction site and one of the rational ways to built reinforced geopolymer structures is the prefabricated construction. The connection of the precast structures is the most vulnerable component under the effect of seismic actions. Proper detailing and design of connections are crucial for sufficiently-ductile performance under seismic loading. Additionally, to achieve the disassembling and reusing of structural members, a demountable connection, i.e., dry connection, should be used instead of a wet connection. In this study, four novel fully-demountable connections for reinforced construction and demolition waste-based (CDW) geopolymer concrete members are developed. Seismic performances of these different demountable connections and one reference monolithic connections are experimentally investigated. The connections are subjected to reversed cyclic lateral displacements under constant axial loading. Comparisons are made referring to observed damage patterns, connection strengths, moment–curvature relations, initial stiffnesses, plastic hinge lengths, and energy dissipation characteristics of the proposed demountable connections and the monolithic connection. The results of the experimental study indicate that one proposed demountable connection exhibited larger lateral capacity and better seismic performance than its monolithic counterpart, whereas the other three proposals showed less performance than the monolithic counterpart. / The authors gratefully acknowledge the financial assistance of the European Union’s Horizon 2020 research and innovation programme under grant agreement No: 869336, ICEBERG

Yes / This paper presents an experimental study on an innovative composite floor system that can be demounted and deconstructed. In this system, the composite slab, formed with profiled metal decking, was connected to a steel beam via demountable shear connectors. A full-scale demountable composite floor system specimen was tested to ultimate load bearing capacity and compared with a similar non-demountable composite floor system specimen using conventional welded headed stud connectors. The experimental results and observations showed that the structural behaviour and load bearing capacity of both composite floor systems are very similar. However, the composite floor system with demountable shear connectors could be deconstructed after testing and the composite slab could be easily detached from the steel beam. The comparison and analysis presented in this paper indicated that the simple design methods currently provided in the Eurocode 4 for the welded shear connections could be used to assess the ultimate moment capacity of demountable composite floor systems.

Yes / Construction and demolition waste (CDW) has reached severe environmental and economic dimensions due to its large volume among all solid waste, highlighting the importance of local actions to manage, recycle, and reuse CDW. Ductile demountable connections are necessary to disassemble and reuse the concrete structural members and fast assembly of precast structures in seismic regions without generating waste. In this study, the seismic performance of CDW-based reinforced geopolymer concrete columns has been investigated. Six ½ scaled columns (half of which were demountable and the other half monolithic) were experimentally tested under reversed cyclic lateral displacement excursions, considering three different levels of constant axial loading to determine failure mechanisms, load–displacement responses, ductilities, energy dissipation capacities, stiffness degradation relations, and curvature distributions. The obtained test results were used to determine the performance of CDWbased geopolymer concrete columns and compare the performances of the demountable connection with the monolithic connection. The test results showed that the novel demountable connection for precast concrete frames exhibited better seismic performance in terms of maximum lateral load capacity, initial stiffness, energy dissipation capacity, and maximum curvature than their monolithic counterparts. Besides, increasing the axial compression ratio on the columns caused an increase in lateral load capacity, energy dissipation capacity, energy dissipation ratio, and initial curvature stiffness; however, it decreased the ductility. Finally, the capacity predictions of current codes, i.e., TS500 and ACI318, were conservative when compared with experimental results. / This publication is a part of doctoral dissertation work by the first author in the Academic Program of Civil Engineering, Institute of Science, Hacettepe University. The authors gratefully acknowledge the financial assistance of the European Union’s Horizon 2020 research and innovation program under grant agreement No: 869336, ICEBERG (Innovative Circular Economy Based solutions demonstrating the Efficient recovery of valuable material Resources from the Generation of representative End-of-Life building material). This work was also supported by Newton Prize 2020. The fifth and seventh authors acknowledge the financial support received from the European Union’s Horizon 2020 research and innovation program under the Marie SkłodowskaCurie grant agreement No 894100. / The full-text of this article will be released for public view at the end of the publisher embargo on 4th Oct 2024.

Yes / This paper presents experimental and numerical investigation on an innovative composite floor system with deconstructability. In this system, a composite slab formed with metal profiled decking is connected to a steel beam using demountable shear connectors. A series of push tests was conducted to investigate the behaviour of this form of shear connectors. In addition to the push tests, a full-scale composite beam was tested to failure in the laboratory under a number of cycles of monotonic loading. For direct comparison, a similar composite beam test was conducted using same section size, concrete strength, but using the conventional welded headed stud connectors. Test results showed that the behaviour of the composite beam with demountable shear connectors is comparable with the specimen with welded shear connectors. After the test was terminated, the demountable shear connectors were unfastened and the composite floor can be easily lifted off from the steel beam. Test result showed that these demountable shear connectors possess high ductility in comparison with the equivalent welded shear connectors. Simple design rules currently use in Eurocode 4 for the welded shear connections and Eurocode 3 for bolts are proposed to predict the shear resistance of this form of demountable shear connectors.

No / Circular economy is an economic system aimed at minimizing wastes and making the most of the current resources. This regenerative approach contrasts with the traditional linear economy, which has been adopted by the construction industry. Developing new construction technologies for sustainable built environment is a top priority for the construction industry throughout the world. Much of the environmental impact from the construction industry is associated with the consumption of resources and generation of waste. The construction industry in Europe consumes over 70,000 million tonnes of materials each year and generates over 250 million tonnes of waste. Composite flooring formed by connecting the concrete slabs to the supporting steel beams has been widely used for many years and is well established as one of the most efficient floor systems in multi storey steel frame building structures. However, shear connectors are welded through the steel decking to the steel beams and cast into the concrete; this made deconstruction and reuse of these components almost impossible. A new composite flooring system which allows for the reuse of the steel beams and composite floor slabs is developed and tested to assess its potential and suitability for reuse. This paper presents the results of a series of full scale beam tests and demonstrates the reusability of this new form of composite flooring systems. Simplified hand calculations are also provided and compared against beam tests / EPSRC, Structural Metal Deck Ltd.

The North House is a proof-of-concept prefabricated solar powered home designed for northern climates, and intended for the research and promotion of high-performance sustainable architecture. Led by faculty at the University of Waterloo, the development and design of the project involved a broad collaboration between faculty and students at the University of Waterloo, with Ryerson University and Simon Fraser University. The North House prototype competed in the U.S. Department of Energy’s Solar Decathlon in October of 2009. This thesis identifies the North House as a component-based building. It illustrates in detail the components of which the house is composed, the sequence by which they are assembled, and the details that allow for the building’s rapid assembly and disassembly. Finally, the thesis explores the possibilities afforded by componentbased architecture including adaptability, off-site fabrication and demountability. Drawing on this, the thesis projects future ways of designing buildings sustainable to both manufacture and operate.

The North House is a proof-of-concept prefabricated solar powered home designed for northern climates, and intended for the research and promotion of high-performance sustainable architecture. Led by faculty at the University of Waterloo, the development and design of the project involved a broad collaboration between faculty and students at the University of Waterloo, with Ryerson University and Simon Fraser University. The North House prototype competed in the U.S. Department of Energy’s Solar Decathlon in October of 2009. This thesis identifies the North House as a component-based building. It illustrates in detail the components of which the house is composed, the sequence by which they are assembled, and the details that allow for the building’s rapid assembly and disassembly. Finally, the thesis explores the possibilities afforded by componentbased architecture including adaptability, off-site fabrication and demountability. Drawing on this, the thesis projects future ways of designing buildings sustainable to both manufacture and operate.