Thesis (MTech. degree in Mechanical Engineering.)--Tshwane University of Technology, 2008.

The introduction of alternative fuels such as natural gas is likely to occur at an increasing rate. The dual-fuel concept allows these low cetane number fuels to be used in compression-ignition (CI, diesel) type engines. Most CI engine conversions have pre-mixed the alternative fuel with air in the intake manifold while retaining diesel injection into the cylinder for ignition. The advantage is that it is simple for practical adaptation; the disadvantage is that good substitution levels are only obtained at midload. A better solution is to inject both the alternative and diesel fuels directly into the cylinder. Here, the fuel in the end-zone is limited and the diesel, injected before the alternative, has only a conventional ignition delay. This improves the high-end performance. Modern, very high pressure diesel injectors have good turndown characteristics as well as better controllability. This improves low-end performance and hence offers an ideal platform for a dual-fuel system. Several systems already exist, mainly for large marine engines but also a few for smaller, truck-sized engines. For the latter, the key is to produce a combined injector to handle both fuels which has the smallest diameter possible so that installation is readily achieved. There exists the potential for much improvement. A combined gas/diesel injection system based on small, high pressure common-rail injectors has been tested for fluid characteristics. Spray properties have been examined experimentally in a test rig and modelled using CFD. The CFD package Fluent was used to model the direct-injection of natural gas and diesel oil simultaneously into an engine. These models were initially calibrated using high-speed photographic visualisation of the jets. Both shadowgraph and schlieren techniques were employed to identify the gas jet itself as well as mixing regions within the flow. Different orientations and staging of the jets with respect to each other were simulated. Salient features of the two fuel jets were studied to optimise the design of a dual-fuel injector for CI engines. Analysis of the fuel-air mixture strength during the injection allowed the ignition delay to be estimated and thus the best staging of the jets to be determined.

published_or_final_version / Environmental Management / Master / Master of Science in Environmental Management

South Africa produces alternative fuels from a number of different sources. The properties of a fuel are known to affect the nature of combustion in compression-ignition engines significantly, and have occasionally resulted in engine failures. Combustion analyses have been conducted on a wide range of fuels and combustion has been thoroughly quantified. However, the role played by the different combustion variables in failures was not known. The result was that it was not possible to predict the implications of variations in the nature of combustion. There was thus a need to investigate the relative role of combustion variables in the failure of engines. The mechanisms of combustion and engine failure were studied. All the variables required to determine combustion and engine durability were measured simultaneously. This research required the development of a complete engine research facility as well as specialized transducers. Fast response surface thermocouples were designed and constructed in order to monitor transient surface temperatures. Heat transfer rates were then calculated with the aid of Fourier analysis. Dynamic stresses were monitored by strain-gauges applied to the engine. A special high speed data acquisition system was developed. An existing heat release model was modified and used to calculate combustion rates. A comprehensive finite element model was developed to calculate piston temperatures and stresses. The role of each combustion variable in stress and durability was investigated by statistical analysis. The results successfully identified the causes of combustion related engine failures. The primary cause of engine failure was found to be thermal loading. The principal cause of any variation in thermal loading and thus engine durability was maximum cylinder pressure. The life of the engine was proved to be determined almost entirely by peak cylinder pressure. The role of the rate of pressure rise was proved to be insignificant. All the implications of variations in the nature of combustion can now be determined accurately. It will thus be possible to optimise engine modifications and fuel properties before validation by durability testing. / Thesis (Ph.D.)-University of Natal, Pietermaritzburg, 1989.

published_or_final_version / Public Administration / Master / Master of Public Administration

published_or_final_version / Environmental Management / Master / Master of Science in Environmental Management

published_or_final_version / Environmental Management / Master / Master of Science in Environmental Management

published_or_final_version / Environmental Management / Master / Master of Science in Environmental Management

published_or_final_version / Transport Policy and Planning / Master / Master of Arts in Transport Policy and Planning