The research discussed in this dissertation was conducted to understand drop formation of inkjet printing with inks containing polymer. Solutions containing a water soluble polymer, poly ethylene oxide (PEO), with different molecular weights and polydispersities were used as inks. A flash photographic technique was used to visualize the whole process of DOD drop formation of dilute polymer solutions. The effects of driving signal, frequency and liquid properties on drop speed, drop size, breakup time and the formation of satellites were studied in detail. The addition of PEO increases the shear viscosity at all molecular weights, but the change is small for dilute solutions. However, the addition of a small amount of PEO can have a significant effect on the DOD drop formation process, increasing breakup time, decreasing primary drop speed and decreasing the number of satellites in some cases. The effects depend on both molecular weight and concentration. At lower molecular weights (14k and 35k g/mol), the effect of PEO was small when the drop formation process for the dilute solution was compared with that of a Newtonian liquid having similar shear viscosity, and the effect of PEO was small even at concentrations large enough that the solution does not fall in the dilute regime. As molecular weight is increased, the effects of PEO on DOD drop formation increase significantly, and the effects of concentration become important. These effects are explained by the fluid elasticity which increases with increasing in molecular weight and concentration. When the liquid jets out of the nozzle, the polymer chains are stretched, and thus depart from their ideal coiled state. As a result, an elastic stress develops in the liquid column and resists capillarity-driven pinch off from the nozzle and is responsible for the decrease in drop speed and longer breakup time. DOD drop formation data were shown to correlate closely with effective relaxation time, proposed by Tirtaatmadja based on Rouse-Zimm theory. When driving voltage amplitude is 44.2 V, two important parameters (breakup time and primary drop speed) in DOD drop formation for solutions containing monodispersed PEO and aqueous solutions containing mixtures of monodispersed PEO were closely predicted by correlation equations involving effective relaxation time . A mixture rule was developed to calculate the relaxation time for mixtures of monodispersed PEO. However, for polydispersed PEO, effective relaxation time was based on viscous molecular weight since the molecular weight distributions of the polydispersed PEO were unknown. When breakup time was plotted versus effective relaxation time for 1000k g/mol PEO, the data did not lie on the same line as that for the 100k and 300k g/mol PEO. This is believed to be due to the molecular weight distributions of the polydispersed PEO. When more than one species are present, viscous average molecular weight does not adequately account for the long chain species making up the polymer sample. DOD drop formation dynamics is highly affected by the actuating waveform, including the driving voltage, waveform shape, and frequency. The effects of parameters (jetting frequency, voltage amplitude and the shape of waveform) characterizing the signal were investigated. The open time and first drop problem were also studied. Research in this dissertation gives a better understanding of DOD drop formation process of polymer solutions, which may lead to improvement of inkjet printing quality for a variety of industry inks and polymer micro scale deposition and patterning in large areas.

No description available.

Le polymer flooding est une des techniques de récupération assistée des hydrocarbures (RAH) ; elle consiste à injecter une solution de polymères de forte masse moléculaire afin de déplacer plus efficacement le pétrole emprisonné dans la roche. Cependant, une limite importante de cette technique est la possible dégradation mécanique des polymères au cours de l'injection et dans le réservoir, due à une scission des chaînes macromoléculaires induite par l’écoulement. Ce travail de thèse a pour objectif de mieux comprendre les mécanismes et scénarios de scission, mais aussi leur impact sur le procédé de polymer flooding. Nous nous sommes intéressés au seuil de dégradation mécanique de solutions de poly(oxyde d’éthylène) et de de polyacrylamide partiellement hydrolysé, pour différents régimes de concentration (solutions diluées et semi-diluées) en régime laminaire et inertiel, et pour des solvants de différentes qualités. L’étude de la dégradation mécanique des solutions et de leur impact sur les propriétés rhéologiques a été menée à l’aide de différents dispositifs de dégradation et de différents rhéomètres, dont un dispositif microfluidique en élongation ; ces techniques de mesure ont été combinées à des mesures de distribution de masses moléculaires par chromatographie d’exclusion stérique couplée à la diffusion de lumière. L’étude montre en premier lieu qu’une composante élongationnelle est indispensable pour dégrader les chaînes macromoléculaires en solution. Les résultats mettent aussi clairement en évidence que les mécanismes de dégradation sont très différents en régime dilué et semi-dilué. En régime dilué, la dégradation mécanique des solutions de polymères est indépendante du régime d’écoulement et affecte préférentiellement les macromolécules de fortes masses, avec une scission en milieu de chaîne. En revanche, en régime semi-dilué, la dégradation mécanique dépend du régime de l’écoulement : en écoulement laminaire, la dégradation est gouvernée par le réseau d’enchevêtrements et la scission des chaînes est aléatoire, tandis qu’en régime inertiel, les chaînes se dégradent comme en régime dilué, avec le même scénario de scission en milieu de chaîne. Par ailleurs, les résultats montrent que les propriétés rhéologiques en élongation peuvent être très fortement impactées par la dégradation mécanique. Enfin, les résultats de l’étude préliminaire des propriétés d’injectivité dans un milieu poreux d’une solution de polymère semi-diluée faiblement dégradée montrent que la dégradation mécanique améliore l’injectivité du polymère aux abords du puits. / Polymer flooding is a technique used in enhanced oil recovery; it consists in injecting high molecular weight polymer solutions in order improve oil sweep efficiency in the reservoir. However, polymer flooding is challenged by possible mechanical degradation of polymer solutions during injection and in the reservoir, due to the flow induced scission of macromolecules. This work aims at better understanding the scission mechanisms and scenarios, but also their impact on polymer flooding. We investigated the onset of mechanical degradation of poly(ethylene oxide) and partially hydrolysed polyacrylamide solutions, for different concentration regimes (dilute and semi-dilute regimes), under laminar or inertial conditions, but also under good or bad solvent conditions. The study of mechanical degradation of polymer solutions and their impact on the rheological properties was performed using different degradation devices and different rheometers, including a microfluidic extensional device; these investigation techniques were combined with measurements of the molecular weight distributions using size exclusion chromatography coupled with light scattering experiments. The study first shows that an extensional component is needed to get a mechanical degradation of polymer chains. The results also clearly show that the degradation mechanisms are very different in dilute and semi-dilute regime. In dilute regime, the mechanical degradation of polymer solutions does not dependent on flow regime and mainly affects the macromolecules with high molecular weights, with a mid-chain scission scenario. On the other hand, in semi-dilute regime, mechanical degradation depends on flow regime: in laminar flows, degradation is governed by the entanglement network and chain scission is random, whereas in inertial flows, chain degradation is similar to that observed in dilute regime, with the same mid-chain scission scenario. Besides, the results show that the extensional rheological properties can be very strongly affected by mechanical degradation. At last, the results of a preliminary study of the injectivity of a slightly degraded semi-dilute polymer solution in porous media show that mechanical degradation improves polymer injectivity near the wellbore.