No description available.

Radical aircraft and propulsion system architecture changes may be required to continue historic performance improvement rates as current civil aircraft and engine technologies mature. Significant fuel-burn savings are predicted to be achieved through the Distributed Propulsion concept, where an array of propulsors is distributed along the span of an aircraft to ingest boundary layer air and increase propulsive efficiency. Studies such as those by NASA predict large performance benefits when integrating Distributed Propulsion with the Blended Wing Body aircraft configuration, as this planform geometry is particularly suited to the ingestion of boundary layer air and the fans can be redesigned to reduce the detrimental distortion effects on performance. Additionally, a conventional aircraft with Distributed Propulsion has not been assessed in public domain literature and may also provide substantial benefits. A conceptual aircraft design code has been developed to enable the modelling of conventional and novel aircraft. A distributed fan tool has been developed to model fan performance, and a mathematical derivation was created and integrated with the fan tool to enable the boundary layer ingestion modelling. A tube & wing Distributed Propulsion aircraft with boundary layer ingestion has been compared with a current technology reference aircraft and an advanced turbofan aircraft of 2035 technology. The advanced tube & wing aircraft achieved a 27.5% fuel-burn reduction relative to the baseline aircraft and the Distributed Propulsion variant showed fuel efficiency gains of 4.1% relative to the advanced turbofan variant due to a reduced specific fuel consumption, produced through a reduction in distributed fan power requirement. The Blended Wing Body with Distributed Propulsion was compared with a turbofan variant reference aircraft and a 5.3% fuel-burn reduction was shown to be achievable through reduced core engine size and weight. The Distributed Propulsion system was shown to be particularly sensitive to inlet duct losses. Further investigation into the parametric sensitivity of the system revealed that duct loss could be mitigated by altering the mass flow and the percentage thrust produced by the distributed fans. Fuel-burn could be further reduced bydecreasing component weight and drag, through decreasing the fan and electrical system size to below that necessary for optimum power or specific fuel consumption.

<p>Solar-powered Unmanned Aerial Vehicles (UAVs) solve the problem of loiter time as aircrafts can fly as long as sufficient illumination and reserve battery power is available. However, Solar-powered UAVs still face the problem of excessive wingspan to increase solar capture area, which detracts from maneuverability and portability. As a result, a feature of merit for solar UAVs has emerged that strives to reduce the wingspan of such UAVs. The purpose of this project is to improve energy use efficiency by applying a distributed propulsion system to reduce the wingspan of solar-powered UAVs and increase payload. The research focuses on optimizing a new design analysis method applied to the distributed propulsion system and further employs the novel application of solar arrays on both top and bottom of the wings. The design methodology will result in a 2.1-meter wingspan, which is the shortest at 2020, for a 24-hour duration solar-powered UAV.</p><br>

No description available.

Investigation of complex multirotor aerodynamic phenomena via wind tunnel experimentation is becoming extremely important with the rapid progress in advanced distributed propulsion VTOL concepts. Much of this experimentation is being performed in large, highly advanced tunnels. However, the proliferation of this class of vehicles extends to small aircraft used by small businesses, universities, and hobbyists without ready access to this level of test facility. Therefore, there is a need to investigate whether multirotor vehicles can be adequately tested in smaller wind tunnel facilities. A test rig for a 2.82-pound quadcopter was developed to perform powered testing in the Cal Poly Aerospace Department’s Low Speed Wind Tunnel, equipped with a 3-foot tall by 4-foot wide test section. The results were compared to data from similar tests performed in the U.S. Army 7-by 10-ft Wind Tunnel at NASA Ames. The two data sets did not show close agreement in absolute terms but demonstrated similar trends. Due to measurement uncertainties, the contribution of wind tunnel interference effects to this discrepancy in measurements was not able to be properly quantified, but is likely a major contributor. Flow visualization results demonstrated that tunnel interference effects can likely be minimized by testing at high tunnel speeds with the vehicle pitched 10-degrees or more downward. Suggestions towards avoiding the pitfalls inherent to multirotor wind tunnel testing are provided. Additionally, a modified form of the conventional lift-to-drag ratio is presented as a metric of electric multirotor aerodynamic efficiency.

The purpose of this study is to examine the multidisciplinary design optimization (MDO) of a distributed propulsion blended-wing-body (BWB) aircraft. The BWB is a hybrid shape resembling a flying wing, placing the payload in the inboard sections of the wing. The distributed propulsion concept involves replacing a small number of large engines with many smaller engines. The distributed propulsion concept considered here ducts part of the engine exhaust to exit out along the trailing edge of the wing. The distributed propulsion concept affects almost every aspect of the BWB design. Methods to model these effects and integrate them into an MDO framework were developed. The most important effect modeled is the impact on the propulsive efficiency. There has been conjecture that there will be an increase in propulsive efficiency when there is blowing out of the trailing edge of a wing. A mathematical formulation was derived to explain this. The formulation showed that the jet "fills in" the wake behind the body, improving the overall aerodynamic/propulsion system, resulting in an increased propulsive efficiency. The distributed propulsion concept also replaces the conventional elevons with a vectored thrust system for longitudinal control. An extension of Spence's Jet Flap theory was developed to estimate the effects of this vectored thrust system on the aircraft longitudinal control. It was found to provide a reasonable estimate of the control capability of the aircraft. An MDO framework was developed, integrating all the distributed propulsion effects modeled. Using a gradient based optimization algorithm, the distributed propulsion BWB aircraft was optimized and compared with a similarly optimized conventional BWB design. Both designs are for an 800 passenger, 0.85 cruise Mach number and 7000 nmi mission. The MDO results found that the distributed propulsion BWB aircraft has a 4% takeoff gross weight and a 2% fuel weight. Both designs have similar planform shapes, although the planform area of the distributed propulsion BWB design is 10% smaller. Through parametric studies, it was also found that the aircraft was most sensitive to the amount of savings in propulsive efficiency and the weight of the ducts used to divert the engine exhaust. / Ph. D.

In recent years, the aircraft industry has begun to focus its research capabilities on reducing emissions and noise produced by aircraft. Modern aircraft use two to four engines arranged on the wing or behind to produce thrust that is concentrated directly behind the engine. Kuchemann suggested a way to improve the propulsive efficiency by changing the normal configuration of engine and aircraft. This concept is the jet-wing distributed propulsion idea, which redistributes the thrust across the span of the wings. Distributed propulsion is accomplished by using many smaller engines spread across the wings or several large engines to duct the exhaust flow in a jet-wing. The jet-wing concept can be used to reduce noise and also as a replacement for flaps and slats by deflecting the jet. Since the distributed propulsion concept is also a method to reduce noise, it's important to have a simplified method of calculating the trailing edge noise of a wing. One of the purposes of this paper was to study the effect of adding jet-wing distributed propulsion to a thick "inboard" airfoil. The two-dimensional jet-wing model was analyzed by parametric computational fluid dynamic (CFD) studies using the Reynolds-averaged, finite-volume, Navier-Stokes code GASP. The model was set up to be self-propelled by applying velocity and density boundary conditions to the blunt edge of the airfoil. A thick "inboard" airfoil from a realistic transonic wing was needed for the study and so the span station of the EET Wing was chosen. This airfoil was thick with a thickness to chord ratio of 16%. In adding distributed propulsion to this thick airfoil, it was found that there was an increase in the propulsive efficiency as compared to typical modern high-bypass-ratio turbofan engines with no negative aerodynamic consequences. The other purpose of this study was to create and assess a simplified method to calculate the trailing edge noise metric value produced by an airfoil. Existing methods use RANS CFD, which is computationally expensive and so it seemed important to find a less expensive method. A method was formed using the Virginia Tech Boundary Layer Java Codes which calculated the characteristic turbulent velocity and characteristic turbulent length scale. A supercritical airfoil, SC(2)-0714, was used to assess the simplified method as compared to the more computationally expensive GASP runs. The results showed that this method has trends that follow those of the GASP results with the method compare well up to modest lift coefficients. / Master of Science

Conventional airliners use two to four engines in a Cayley-type arrangement to provide thrust, and the thrust from these engines is typically concentrated right behind the engine. Distributed propulsion is the idea of redistributing the thrust across most, or all, of the wingspan of an aircraft. This can be accomplished by using several large engines and using a duct to spread out the exhaust flow to form a jet-wing or by using many small engines spaced along the span of the wing. Jet-wing distributed propulsion was originally suggested by Kuchemann as a way to improve propulsive efficiency. In addition, one can envision a jet-wing with deflected jets replacing flaps and slats and the associated noise. The purpose of this study was to assess the performance benefits of jet-wing distributed propulsion. The Reynolds-averaged, finite-volume, Navier-Stokes code GASP was used to perform parametric computational fluid dynamics (CFD) analyses on two-dimensional jet-wing models. The jet-wing was modeled by applying velocity and density boundary conditions on the trailing edges of blunt trailing edge airfoils such that the vehicle was self-propelled. As this work was part of a Blended-Wing-Body (BWB) distributed propulsion multidisciplinary optimization (MDO) study, two airfoils of different thickness were modeled at BWB cruise conditions. One airfoil, representative of an outboard BWB wing section, was 11% thick. The other airfoil, representative of an inboard BWB wing section, was 18% thick. Furthermore, in an attempt to increase the propulsive efficiency, the trailing edge thickness of the 11% thick airfoil was doubled in size. The studies show that jet-wing distributed propulsion can be used to obtain propulsive efficiencies on the order of turbofan engine aircraft. If the trailing edge thickness is expanded, then jet-wing distributed propulsion can give improved propulsive efficiency. However, expanding the trailing edge must be done with care, as there is a drag penalty. Jet-wing studies were also performed at lower Reynolds numbers, typical of UAV-sized aircraft, and they showed reduced propulsive efficiency performance. At the lower Reynolds number, it was found that the lift, drag, and pitching moment coefficients varied nearly linearly for small jet-flap deflection angles. / Master of Science

The objective of this research is to examine how to design low-noise transport aircraft using Multidisciplinary Design Optimization (MDO). The subject is approached by designing for low-noise both implicitly and explicitly. The explicit design approach involves optimizing an aircraft while explicitly constraining the noise level. An MDO framework capable of optimizing both a cantilever wing and a Strut-Braced-Wing (SBW) aircraft was developed. The framework employs aircraft analysis codes previously developed at the Multidisciplinary Design and Analysis (MAD) Center at Virginia Tech (VT). These codes have been improved here to provide more detailed and realistic analysis. The Aircraft Noise Prediction Program (ANOPP) is used for airframe noise analysis. The objective is to use the MDO framework to design aircraft for low-airframe-noise at the approach conditions and quantify the change in weight and performance with respect to a traditionally designed aircraft. The results show that reducing airframe noise by reducing approach speed alone, will not provide significant noise reduction without a large performance and weight penalty. Therefore, more dramatic changes to the aircraft design are needed to achieve a significant airframe noise reduction. Another study showed that the trailing-edge (TE) flap can be eliminated, as well as all the noise associated with that device, without incurring a significant weight and performance penalty. To achieve approximately 10 EPNdB TE flap noise reduction the flap area was reduced by 82% while the wing reference area was increased by 12.4% and the angle of attack increased from 7.6 degrees to 12.1 degrees to meet the required lift at approach. The wing span increased by approximately 2.2%. Since the flap area is being minimized, the wing weight suffers only about a 2,000 lb penalty. The increase in wing span provides a reduction in induced drag to balance the increased parasite drag due to a lower wing aspect ratio. As a result, the aircraft has been designed to have minimal TE flaps without any significant performance penalty. If noise due to the leading-edge (LE) slats and landing gear are reduced, which is currently being pursued, the elimination of the flap will be very significant as the clean wing noise will be the next 'noise barrier'. Lastly, a comparison showed that SBW aircraft can be designed to be 10% lighter and require 15% less fuel than cantilever wing aircraft. Furthermore, an airframe noise analysis showed that SBW aircraft with short fuselage-mounted landing gear could have similar or potentially a lower airframe noise level than comparable cantilever wing aircraft. The implicit design approach involves selecting a configuration that supports a low-noise operation, and optimizing for performance. A Blended-Wing-Body (BWB) transport aircraft has the potential for significant reduction in environmental emissions and noise compared to a conventional transport aircraft. A BWB with distributed propulsion was selected as the configuration for the implicit low-noise design in this research. An MDO framework previously developed at the MAD Center at Virginia Tech has been refined to give more accurate and realistic aircraft designs. To study the effects of distributed propulsion, two different BWB configurations were optimized. A conventional propulsion BWB with four pylon mounted engines and two versions of a distributed propulsion BWB with eight boundary layer ingestion inlet engines. A 'conservative' distributed propulsion BWB design with a 20% duct weight factor and a 95% duct efficiency, and an 'optimistic' distributed propulsion BWB design with a 10% duct weight factor and a 97% duct efficiency were studied. The results show that 65% of the possible savings due to 'filling in' the wake are required for the 'optimistic' distributed propulsion BWB design to have comparable $TOGW$ as the conventional propulsion BWB, and 100% savings are required for the 'conservative' design. Therefore, considering weight alone, this may not be an attractive concept. Although a significant weight penalty is associated with the distributed propulsion system presented in this study, other characteristics need to be considered when evaluating the overall effects. Potential benefits of distributed propulsion are, for example, reduced propulsion system noise, improved safety due to engine redundancy, a less critical engine-out condition, gust load/flutter alleviation, and increased affordability due to smaller, easily-interchangeable engines. / Ph. D.

This master’s thesis discusses the impact of air traffic on our environment. The fuels combustion, the conditions necessary for realization of air traffic, or the situations resulting from it, such as aircraft maintenance, noise, emergencies, etc., have a negative impact on not only on the environment, but also on health and comfort of people, as well as flora and fauna, exposed to these conditions. Apart from the air traffic impacts on our environment mentioned above, the thesis also describes especially the possibilities of their reduction and companies dealing with them. The large main part of thesis paper is dedicated to an analysis of a new aircraft design technology, which should reduce the production of emissions in the future.