With the advent of wide bandgap (WBG) semiconductor devices, the electromagnetic interference (EMI) emissions are more pronounced due to high slew rates in the form of high dv/dt and high di/dt at higher switching frequencies compared to the traditional silicon technology. To comply with the stringent conducted emission requirements, EMI filters are adopted to attenuate the high frequency common mode (CM) and differential mode (DM) noise through the propagation path. However, self and mutual parasitic components are known to degrade the EMI filter performance. While parasitic cancellation techniques have been discussed at length in prior literature, most of them have focused mainly on single phase applications. As such this work focuses on extending the preexisting concepts to three-phase systems. Novel component placement, winding strategy as well as shielding and grounding techniques were developed to desensitize the influence of the parasitic effects on a three-phase multi-stage filter. The effectiveness of the three-phase filter structure employing the proposed methodologies has been validated via noise measurements at the line impedance stabilization network (LISN) in a 15kW rated motor drive system. Consequently, general design guidelines have been formulated for filter topologies with different inductor and capacitor form-factors. / Master of Science / The adoption of wide bandgap (WBG) semiconductor devices, such as Silicon Carbide (SiC) or Gallium Nitride (GaN) transistors, improves the power density with higher slew rates and switching frequencies compared to the traditional Silicon technology. However, the high switching speeds and high frequencies have generated higher electromagnetic interference (EMI) noise in the surroundings. To comply with the conducted emission requirements at the grid terminal, EMI filter is mandatory to attenuate the high frequency EMI noise that flows into grid. However, near field and the effect of parasitic components are known to degrade the filter performance at the higher end of frequency spectrum where the limit lines are typically stringent. While parasitic cancellation techniques have been discussed at length in prior literature, most of them has focused mainly on single phase applications. Therefore, this thesis aims to extend the pre-existing concepts to compensate the mutual and self-parasitic coupling components in a three-phase multi-stage filter. In this regard, novel component placement, winding strategy as well as shielding and grounding techniques were developed to compensate for the parasitic effects in a three- phase multi-stage filter. The effectiveness of the three-phase filter structure employing the proposed methodologies has been validated in a 15kW rated motor drive system. Consequently, general design guidelines have been formulated for filter design with minimal parasitic effects.

No description available.

Rapidly-increasing medium-voltage power electronics applications in emerging industry systems, including electrical ships, more electric aircraft, and microgrids, have emphasized the critical need for highly energy-efficient, reliable, and fast switching devices. As a result, Wide-Bandgap (WBG) devices have gained considerable interest over conventional silicon-based switches in recent years. For example, emerging WBG devices have unlocked new dimensions for modern motor drive systems with increased efficiency, switching frequency, and superior power density. Commercially-developed WBG devices such as Silicon Carbide (SiC) and Gallium Nitride (GaN) offer promising opportunities to meet those pressing requirements. However, the fast switching operation of WBG devices may cause substantially increased EMI emissions in medium-voltage applications, which can decrease the overall system’s performance or merits of power converters. This will be particularly an issue in a system where electric ground is unavailable, such as an electric ship, as a large Electro-Magnetic Interference current will be circulating within the system. The EMI in the WBG switch module will be emitted up to 500 MHz. This is the near radio-frequency (RF) band whose impact had not been clearly understood or properly analyzed in the power electronics field until recently. With new and critical challenges in recent years, to reliably adopt WBG devices in emerging power systems, there has been significant effort to improve electromagnetic compatibility (EMC) with new EMI mitigation techniques that comply with existing standards, including International Special Committee on Radio Interference (CISPR), Federal Communications Commission (FCC), Department of Defense (DOD), International Electro-Technical Commission (IEC), etc. This research investigates the common-mode EMI in networked power electronics-enabled power systems. Common-mode EMI phase information is a vital degree of freedom in EMI study that has not been considered in the state of the art. The EMI phase information reduces EMI without implementing any active or passive filter circuit. An effective and less complex method is introduced to reduce EMI in power electronics network. The work includes developing hybrid filter with passive and virtual filter. Including virtual filter reduces the passive common mode choke weight and volume significantly. Finally, a simplified switching node capacitance characterization technique for packaged WBG SiC has been introduced.

Power factor correction (PFC) converter is a species of switching mode power supply (SMPS) which is widely used in offline frond-end converter for the distributed power systems to reduce the grid harmonic distortion. With the fast development of information technology and multi-media systems, high frequency PFC power supplies for servers, desktops, laptops and flat-panel TVs, etc. are required for more efficient power delivery within limited spaces. Therefore the critical conduction mode (CRM) PFC converter has been becoming more and more popular for these information technology applications due to its advantages in inherent zero-voltage soft switching (ZVS) and negligible diode reverse recovery. With the emerging of the high voltage GaN devices, the goal of achieving soft switching for high frequency PFC converters is the top priority and the trend of adopting the CRM PFC converter is becoming clearer. However, there is the stringent electromagnetic interference (EMI) regulation worldwide. For the CRM PFC converter, there are several challenges on meeting the EMI standards. First, for the CRM PFC converter, the switching frequency is variable during the half line cycle and has very wide range dependent on the AC line RMS voltage and the load, which makes it unlike the traditional constant-frequency PFC converter and therefore the knowledge and experience of the EMI characteristics for the traditional constant-frequency PFC converter cannot be directly applied to the CRM PFC converter. Second, for the CRM PFC converter, the switching frequency is also dependent on the inductance of the boost inductor. It means the EMI spectrum of the CRM PFC converter is tightly related the boost inductor selection during the design of the PFC power stage. Therefore, unlike the traditional constant-frequency PFC converter, the selection of the boost inductor is also part of the EMI filter design process and EMI filter optimization should begin at the same time when the power stage design starts. Third, since the EMI filter optimization needs to begin before the proto-type of the CRM PFC converter is completed, the traditional EMI-measurement based EMI filter design will become much more complex and time-consuming if it is applied to the CRM PFC converter. Therefore, a new methodology must be developed to evaluate the EMI performance of the CRM PFC converter, help to simplify the process of the EMI filter design and achieve the EMI filter optimization. To overcome these challenges, a novel mathematical analysis method for variable frequency PFC converter is thus proposed in this dissertation. Based on the mathematical analysis, the quasi-peak EMI noise, which is specifically required in most EMI regulation standards, is investigated and accurately predicted for the first time. A complete approximate model is derived to predict the quasi-peak DM EMI noise for the CRM PFC converter. Experiments are carried out to verify the validity of the prediction. Based on the DM EMI noise prediction, worst case analysis is carried out and the worst DM EMI noise case for all the input line and load conditions can be found to avoid the overdesign of the EMI filter. Based on the discovered worst case, criteria to ease the DM EMI filter design procedure of the CRM boost PFC are given for different boost inductor selection. Optimized design procedure of the EMI filter for the front-end converter is then discussed. Experiments are carried out to verify the validity of the whole methodology. / Ph. D. / Power factor correction (PFC) converter is widely used in offline frond-end converter for the distributed power systems to reduce the grid harmonic distortion. With the fast development of information technology and multi-media systems, high frequency PFC power supplies for servers, desktops, laptops and flat-panel TVs, etc. are required for more efficient power delivery within limited spaces. Therefore the critical conduction mode (CRM) PFC converter has been becoming more and more popular for these information technology applications. However, there is the stringent electromagnetic interference (EMI) regulation worldwide. For the CRM PFC converter, there are many challenges on meeting the EMI standards. To overcome these challenges, a novel mathematical analysis method for variable frequency PFC converter is thus proposed in this dissertation. A complete approximate model is derived to predict the quasi-peak DM EMI noise for the CRM PFC converter. Experiments are carried out to verify the validity of the prediction. Based on the DM EMI noise prediction, worst case analysis is carried out and based on the discovered worst case, criteria to ease the DM EMI filter design procedure of the CRM boost PFC are given for different boost inductor selection. Optimized design procedure of the EMI filter for the front-end converter is then discussed. Experiments are carried out to verify the validity of the whole methodology.