Since concrete bridge deck slabs are much longer in the traffic direction, they experience transverse early-age cracks due to volumetric instability and restraint. In the last decade, the lower cost of the non-corrodible Glass Fiber Reinforced Polymer (GFRP) bars, as alternative to steel reinforcement, has made them attractive to the bridge construction industry. However, low modulus of GFRP bars may lead to wider cracks in GFRP-RC structures. This serviceability issue can be aggravated by harsh environmental conditions. Hence, the main objective of this thesis is to investigate the effect of early-age cracking in restraint bridge deck slabs reinforced with GFRP bars subjected to different environments. This research consists of two phases: an experimental investigation and a numerical study. In the experimental phase, four full-scale cast-in-place slabs reinforced with different longitudinal GFRP reinforcement ratios (0.30, 0.50, 0.70 and 1.1%) and one with steel reinforcement ratio of 0.7% measuring 2500 mm long × 765 mm wide × 180 mm thick were constructed and tested in the laboratory. Three environmental conditions were implemented; normal (laboratory) adiabatic conditions as well as freezing-thawing and wetting-drying cycles. The main test results are presented in terms of cracking pattern, width and spacing, and strains in the reinforcement and concrete. Test results indicated that the minimum reinforcement ratio (0.7%) recommended by CHBDC for bridge deck slabs reinforced with GFRP bars satisfied the serviceability requirements after being subjected to the simulated exposures of normal laboratory conditions, freezing-thawing, and wetting-drying cycles. In the numerical phase of this research, a finite element model (FEM) was constructed using ATENA software package (ver. 5) to simulate the behaviour of the test specimens. According to the FEM results, a reinforcement ratio of 0.45% Carbon FRP (CFRP) can control the early-age crack width and reinforcement strain in CFRP-RC members subjected to restrained shrinkage. Also, the results indicated that changing the bar surface texture (sand-coated and ribbed bars) or concrete cover had an insignificant effect on the early-age crack behavior of FRP-RC bridge deck slabs subjected to shrinkage. However, reducing bar spacing and concrete strength resulted in a decrease in crack width and reinforcement strain. / October 2015

Dans une démarche de valorisation des déchets, les granulats recyclés sont introduits dans la formulation des bétons pour donner naissance à de nouveaux bétons recyclés qui représentent l’objet du projet national RECYBETON et du projet ANR ECOREB. Cette thèse se concentre sur l’étude du béton frais et en particulier la maîtrise du retrait plastique et l’effet du degré de saturation initial des gravillons recyclés sur le comportement des bétons recyclés. Deux familles de bétons avec des rapports eau/ciment respectifs de 0,6 et 0,45 ont été testés en conditions endogènes ainsi qu’en dessiccation (Vvent = 8 m/s). Chaque famille de bétons est constituée d’un béton naturel de référence et de deux bétons recyclés différenciés pas le degré initial de saturation des gravillons recyclés (50 et 120 % de l’absorption nominale). Les résultats expérimentaux soulignent la capacité des gravillons recyclés initialement partiellement saturés à capter rapidement l’eau contenue dans la pâte de ciment, modifiant ainsi le rapport E/C, les propriétés rhéologiques du béton frais et les résistances mécaniques du béton durci. Après saturation en eau, si les conditions de séchage conduisent à un manque d’eau dans le béton, les gravillons recyclés peuvent fournir de l’eau à la pâte. Ils constituent donc un potentiel de cure interne. Le retrait plastique sous vent est explicitement lié au ressuage, au développement de la pression capillaire et à la fissuration. Le temps d’initiation de la fissuration dépend de la quantité d’eau totale dans le béton et de sa capacité à ressuer tandis que l’ouverture de fissure varie avec la valeur de retrait plastique mesurée. Dans cette étude, le développement de la pression capillaire est la cause de la fissuration qui apparaît dès l’entrée d’air dans le matériau poreux. Les différences de comportements les plus importantes sont observées entre bétons ayant une quantité d’eau totale différente plutôt qu’entre bétons naturel et recyclé. La compilation des résultats expérimentaux a permis de mettre sur pied des modélisations qui illustrent les comportements observés. Les pores concernés par l’entrée d’air dans les bétons recyclés et naturels au moment de la fissuration sont les plus gros pores de la pâte. Enfin, un couplage hygrothermique séchage-température du béton peut influer sur le démarrage de l’hydratation. / In the context of sustainable development, the reuse of construction and demolition waste is necessary to conserve nonrenewable natural aggregate resources, so recycled aggregates are introduced in concrete mix design. This is the aim of the national projet RECYBETON and the research project ECOREB. This study deals with the fresh concrete and more specifically with shrinkage control and the effects of the initial saturation degrees of recycled coarse aggregates on concrete behavior.Two concrete families, with two different water/cement ratios 0,60 and 0,45, are tested under endogenous and drying (wind speed equal to 8 m/s) conditions. Each concrete family contains a reference natural concrete and two recycled concretes. The initial saturation degree is the difference between them (recycled coarse aggregates saturated or semi saturated).Experimental results underline the capacity of non-saturated aggregates to quickly absorb water from cement paste, modifying the W/C ratio, rheological properties of the fresh concrete and the mechanical strength (at 28 days) of recycled concretes. After saturation in water, recycled aggregates can release water into the cement paste if the undergone drying conditions lead to a lack of water in the cement matrix. The recycled coarse aggregates can be seen as an internal curing potential.Experimental plastic shrinkage studies carried out under drying conditions highlight a link between bleeding, capillary pressure, plastic shrinkage and cracking. It should be pointed out that the initial cracking is dependent on the total quantity of water in the concrete and on its bleeding capacity. The opening cracks vary with the plastic shrinkage values measured during the test. The analysis of the results emphasize that the capillary pressure is the determining parameter and that the air entry value matches the cracks. The major behavior differences are found between concretes with different volumes of water rather than between natural and recycled concretes.Finally, the analysis of all the experimental results have allowed concrete modelling and understanding why concretes do not behave in the same way. When it cracks, the air come in the biggest pores of the concrete paste. Moreover, a hygrothermal coupling exists between the drying and the temperature in concrete. It can affect hydration start up.