Electrochemical Supercapacitors (ES), also known as Supercapacitor or Ultracapacitor, has been regarded as an advanced electrical energy storage device for decades. Fabrication of advanced electrode materials is of critical importance for advanced ES. Among various materials used for ES electrode, polypyrrole (PPy) is found to be a promising material due to high specific capacitance, good electrical conductivity, low cost and ease of processing. The use of advanced anionic dopants and addition of multiwall carbon nanotube (MWCNT) have been proved an .effective approach towards advanced PPy based ES with improved electrochemical behaviors. In this research, chemical polymerization of PPy powders and PPy/MWCNT composite materials have been successfully accomplished in presence of advanced anionic dopants, including chromotrope families, amaranth, pyrocatechol violet, eriochrome cyanine R and acid fuchsin. The influence of polyaromatic dopants with different molecular size, charges and charge to mass ratios on the microstructure and electrochemical characteristics has been discussed. PPy coated MWCNT with uniform microstructures was successfully achieved in simple chemical methods. The results showed PPy powders with enhanced microstructures and electrochemical behaviors can be obtained by using such advanced anionic dopants. Multi-charged polyaromatic dopants with larger molecular size benefitted PPy powders with smaller particle size, improved specific capacitance, and enhanced cycling stability, at high electrode mass loadings. Moreover, advanced aromatic dispersant and chemical synthesis was proved a simple and effective method for fabrication of PPy/MWCNT composite materials at different PPy/MWCNT mass ratio, among which the powder with PPy/MWCNT mass ratio of 7:3 showed optimum electrochemical performance. Last but not the least, the use of advanced high porosity current collector (Ni foam) allowed high electrode mass loading and good electric conductivity. As a result, advanced PPy/MWCNT composite materials which allows improved electrochemical behaviors, especially at high mass loading, are promising electrode materials for ES. / Thesis / Master of Applied Science (MASc)

Energy storage provides sustainability when coupled with renewable but intermittent energy sources such as solar, wave and wind power, and electrochemical supercapacitors represent a new storage technology with high power and energy density. For inclusion in supercapacitors, transition metal oxide and sulfide electrodes such as RuO2, IrO2, TiS2, and MoS2 exhibit rapid faradaic electron–transfer reactions combined with low resistance. The pseudocapacitance of RuO2 is about 720 F/g, and is 100 times greater than double-layer capacitance of activated carbon electrodes. Due to the two-dimensional layered structure of MoS2, it has proven to be an excellent electrode material for electrochemical supercapacitors. Cathodic electrodeposition of MoS2 onto glassy carbon electrodes is obtained from electrolytes containing (NH4)2MoS4 and KCl. Annealing the as-deposited Mo sulfide deposit improves the capacitance by a factor of 40x, with a maximum value of 360 F/g for 50 nm thick MoS2 films. The effects of different annealing conditions were investigated by XRD, AFM and charge storage measurements. The specific capacitance measured by cyclic voltammetry is highest for MoS2 thin films annealed at 500°C for 3h and much lower for films annealed at 700°C for 1 h. Inclusion of copper as a dopant element into electrodeposited MoS2 thin films for reducing iR drop during film charge/discharge is also studied. Thin films of Cu-doped MoS2 are deposited from aqueous electrolytes containing SCN-, which acts as a complexing agent to shift the cathodic Cu deposition potential, which is much more anodic than that of MoS2. Annealed, Cu-doped MoS2 films exhibit enhanced charge storage capability about 5x higher than undoped MoS2 films. Coal combustion is currently the largest single anthropogenic source of CO2 emissions, and due to the growing concerns about climate change, several new technologies have been developed to mitigate the problem, including oxyfuel coal combustion, which makes CO2 sequestration easier. One complication of oxyfuel coal combustion is that corrosion problems can be exacerbated due to flue gas recycling, which is employed to dilute the pure O2 feed and reduce the flame temperature. Refractory metal diffusion coatings of Ti and Zr atop P91 steel were created and tested for their ability to prevent corrosion in an oxidizing atmosphere at elevated temperature. Using pack cementation, diffusion coatings of thickness approximately 12 and 20 µm are obtained for Ti and Zr, respectively. The effects of heating to 950°C for 24 hr in 5% O2 in He are studied in situ by thermogravimetric analyses (TGA), and ex situ by SEM analyses and depth profiling by EDX. For Ti-coated, Zr-coated and uncoated P91 samples, extended heating in an oxidizing environment causes relatively thick oxide growth, but extensive oxygen penetration greater than 2.7 mm below the sample surface, and eventual oxide exfoliation, are observed only for the uncoated P91 sample. For the Ti- and Zr-coated samples, oxygen penetrates approximately 16 and 56 µm, respectively, below the surface. In situ TGA verifies that Ti-and Zr-coated P91 samples undergo far smaller mass changes during corrosion than uncoated samples, reaching close to steady state mass after approximately four hours.

<p>No comments. Thanks.</p> / <p>Advanced electrodes based on MnO₂ for the electrochemical supercapacitor (ES) application have been fabricated using electrochemical and chemical methods.</p> <p>Electrosynthesis method has been utilized for the in-situ impregnation of manganese dioxide in commercial Ni plaque current collectors. Dipping-reduction, cathodic galvanostatic and reverse pulse electrosynthesis methods were investigated. The material loading was varied by the variation of the number of the dipping-reduction procedures in the chemical precipitation method or by the variation of charge passed in the electrochemical methods. The results obtained by different methods were compared. The dipping-reduction method offered the advantage of higher specific capacitances (SCs) at high scan rates, whereas other methods allowed higher material synthesis rate.</p> <p>Cathodic electrolytic deposition (ELD) has been utilized for the fabrication of Ag-doped MnO₂ films. The Ag-doped MnO₂ films showed improved capacitive behavior and lower electrical resistance of 0.6 Ohm compared to pure MnO₂ films. The highest SC of 770 F g^-1 was obtained at a scan rate of 2 mV s^-1 in the 0.5 M Na₂SO₄ electrolyte.</p> <p>Electrodes for ES application were fabricated by cathodic electrodeposition of MnO₂ on CNTs, which were grown by chemical vapor deposition on stainless steel meshes. The MnO₂-CNT nanocomposites showed excellent capacitive behavior and low electrical resistance of 0.5 Ohm.</p> <p>Electrophoretic deposition (EPD) has been utilized for the deposition of composite MnO₂-multiwalled carbon nanotube (MWCNT) films for the ES application. Dopamine (DA), caffeic acid (CA), tyramine (TA), gallic acid (GA), polyacrylic acid (PAA) and pyrocatechol violet (PV) were shown to be effective and universal charging additives, which provide stabilization of MnO₂ nanoparticles and MWCNTs in the suspensions. The influence of the structure of the organic molecules on their adsorption on the oxide nanoparticles has been investigated. We discovered that the number and site of OH group for dispersants were essential for the adsorption on oxide materials, and the number of aromatic ring was important for the adsorption on carbon materials. Pure CNT films were deposited using PV as a dispersant, which was the first time in literature to prepare pure CNT film using a dispersant. SCs decrease with increasing film thickness. SCs of composite MnO₂-MWCNT obtained using EPD were in the range of 350-650 F g^-1 depending on material loadings.</p> / Doctor of Science (PhD)

Magister Scientiae - MSc (Chemistry) / Blending polymers together offers researchers the ability to create novel materials that have a combination of desired properties of the individual polymers for a variety of functions as well as improving specific properties. The behaviour of the resulting blended polymer or blend is determined by the interactions between the two polymers. The resultant synergy from blending an intrinsically conducting polymer like polyaniline (PANI), is that it possesses the electrical, electronic, magnetic and optical properties of a metal while retaining the poor mechanical properties, solubility and processibility commonly associated with a conventional polymer. Aromatic polyamic acid has outstanding thermal, mechanical, electrical, and solvent resistance properties that can overcome the poor mechanical properties and instability of the conventional conducting polymers, such as polyaniline.