The thesis presents new methodology and algorithms that can be used to analyse and measure the hand tremor and fatigue of surgeons while performing surgery. This will assist them in deriving useful information about their fatigue levels, and make them aware of the changes in their tool point accuracies. This thesis proposes that muscular changes of surgeons, which occur through a day of operating, can be monitored using Electromyography (EMG) signals. The multi-channel EMG signals are measured at different muscles in the upper arm of surgeons. The dependence of EMG signals has been examined to test the hypothesis that EMG signals are coupled with and dependent on each other. The results demonstrated that EMG signals collected from different channels while mimicking an operating posture are independent. Consequently, single channel fatigue analysis has been performed. In measuring hand tremor, a new method for determining the maximum tremor amplitude using Principal Component Analysis (PCA) and a new technique to detrend acceleration signals using Empirical Mode Decomposition algorithm were introduced. This tremor determination method is more representative for surgeons and it is suggested as an alternative fatigue measure. This was combined with the complexity analysis method, and applied to surgically captured data to determine if operating has an effect on a surgeon’s fatigue and tremor levels. It was found that surgical tremor and fatigue are developed throughout a day of operating and that this could be determined based solely on their initial values. Finally, several Nonlinear AutoRegressive with eXogenous inputs (NARX) neural networks were evaluated. The results suggest that it is possible to monitor surgeon tremor variations during surgery from their EMG fatigue measurements.

The number of remote sensing platforms and sensors rises almost every year, yet much work on the interpretation of land cover is still carried out using either single images or images from the same source taken at different dates. Two questions could be asked of this proliferation of images: can the information contained in different scenes be used to improve the classification accuracy and, what is the best way to combine the different imagery? Two of these multiple image sources are MODIS on the Terra platform and ETM+ on board Landsat7, which are suitably complementary. Daily MODIS images with 36 spectral bands in 250-1000 m spatial resolution and seven spectral bands of ETM+ with 30m and 16 days spatial and temporal resolution respectively are available. In the UK, cloud cover may mean that only a few ETM+ scenes may be available for any particular year and these may not be at the time of year of most interest. The MODIS data may provide information on land cover over the growing season, such as harvest dates, that is not present in the ETM+ data. Therefore, the primary objective of this work is to develop a methodology for the integration of medium spatial resolution Landsat ETM+ image, with multi-temporal, multi-spectral, low-resolution MODIS \Terra images, with the aim of improving the classification of agricultural land. Additionally other data may also be incorporated such as field boundaries from existing maps. When classifying agricultural land cover of the type seen in the UK, where crops are largely sown in homogenous fields with clear and often mapped boundaries, the classification is greatly improved using the mapped polygons and utilising the classification of the polygon as a whole as an apriori probability in classifying each individual pixel using a Bayesian approach. When dealing with multiple images from different platforms and dates it is highly unlikely that the pixels will be exactly co-registered and these pixels will contain a mixture of different real world land covers. Similarly the different atmospheric conditions prevailing during the different days will mean that the same emission from the ground will give rise to different sensor reception. Therefore, a method is presented with a model of the instantaneous field of view and atmospheric effects to enable different remote sensed data sources to be integrated.

This study explores the technological and economic aspects of the competition between natural rubber and the synthetics of the general purpose class. The first part of the thesis reviews the overall competitive position of natural rubber and its future prospects. The effects of the structure of the rubber producing industry (-natural and synthetic), economics of production, characteristics of demand and some aspects of marketing on the short and long term competitive position are analysed. It is concluded that natural rubber can remain competitive in all aspects if, greater co-operation between the natural rubber producers can be achieved to formulate a unified programme of production, research and development and marketing. In view of certain problems peculiar to Sri Lanka, the second part analyses the state of the rubber industry in Sri Lanka in respect of the changes taking place in other natural rubber producing countries, the developments in the synthetic rubber industry and the changing technological requirements of the rubber consuming industries. The commercial, economic and technical viability of certain projects in Sri Lanka and the areas for future research at the Rubber Research Institute of Sri Lanka are briefly explored. Since Sri Lanka is the largest producer of premium grade pale crepe rubber and in view of the declining demand for this rubber, the competitive position of pale crepe is studied in some detail and some recommendations are included to improve its competitive position. In view of the anticipated strong demand for natural rubber in the future, it is recommended that Sri Lanka should plan now to increase rubber production at a faster rate by 1980’s. It is also concluded that it is desirable to produce more special purpose premium grades of natural rubber in Sri Lanka than to produce more complex derivatives in the short term and a long term approach towards producing powdered rubber, liquid and thermoplastic rubber from latex is necessary.

High velocity oxyfuel (HVOF) thermal spraying is one of the most significant developments in the thermal spray industry since the development of the original plasma spray technique. The first investigation deals with the combustion and discrete particle models within the general purpose commercial CFD code FLUENT to solve the combustion of kerosene and couple the motion of fuel droplets with the gas flow dynamics in a Lagrangian fashion. The effects of liquid fuel droplets on the thermodynamics of the combusting gas flow are examined thoroughly showing that combustion process of kerosene is independent on the initial fuel droplet sizes. The second analysis copes with the full water cooling numerical model, which can assist on thermal performance optimisation or to determine the best method for heat removal without the cost of building physical prototypes. The numerical results indicate that the water flow rate and direction has noticeable influence on the cooling efficiency but no noticeable effect on the gas flow dynamics within the thermal spraying gun. The third investigation deals with the development and implementation of discrete phase particle models. The results indicate that most powder particles are not melted upon hitting the substrate to be coated. The oxidation model confirms that HVOF guns can produce metallic coating with low oxidation within the typical standing-off distance about 30cm.

The possible evaporation of lubricant in fluid film bearings has been investigated theoretically and by experiment using a radial flow hydrostatic bearing supplied with liquid refrigerant R114. Good correlation between measured and theoretical values was obtained using a bespoke computational fluid dynamic model in which the flow was assumed to be laminar and adiabatic. The effects of viscous dissipation and vapour generation within the fluid film are fully accounted for by applying a fourth order Runge-Kutta routine to satisfy the radial and filmwise transverse constraints of momentum, energy and mass conservation. The results indicate that the radial velocity profile remains parabolic while the flow remains in the liquid phase and that the radial rate of enthalpy generation is then constant across the film at a given radius. The results also show that evaporation will commence at a radial location determined by geometry and flow conditions and in fluid layers adjacent to the solid boundaries. Evaporation is shown to progress in the radial direction and the load carrying capacity of such a bearing is reduced significantly. Expressions for the viscosity of the liquid/vapour mixture found in the literature survey have not been tested against experimental data. A new formulation is proposed in which the suitable choice of a characteristic constant yields close representation to any of these expressions. Operating constraints imposed by the design of the experimental apparatus limited the extent of the surface over which evaporation could be obtained, and prevented clear identification of the most suitable relationship for the viscosity of the liquid/vapour mixture. The theoretical model was extended to examine the development of two phase flow in a rotating shaft face seal of uniform thickness. Previous theoretical analyses have been based on the assumption that the radial velocity profile of the flow is always parabolic, and that the tangential component of velocity varies linearly from the value at the rotating surface, to zero at the stationary surface. The computational fluid dynamic analysis shows that viscous shear and dissipation in the fluid adjacent to the rotating surface leads to developing evaporation with a consequent reduction in tangential shear forces.

In Ghana, a country with an expanding population and high potential for economic growth, agriculture is an important resource; however, most of the crop production is restricted to low technology shifting cultivation agriculture. The high intensity seasonal rainfall coincides with the early growing period of many of the crops meaning that plots are very susceptible to erosion, especially on steep sided valleys in the region south of Lake Volta. This research investigated the processes of soil erosion by rainfall with the aim of producing a sediment yield model for a small semi-agricultural catchment in rural Ghana. Various types of modelling techniques were considered to discover those most applicable to the sub-tropical environment of Southern Ghana. Once an appropriate model had been developed and calibrated, the aim was to look at how to enable the scaling up of the model using sub-catchments to calculate sedimentation rates of Lake Volta. An experimental catchment was located in Ghana, south west of Lake Volta, where data on rainstorms and the associated streamflow, sediment loads and soil data (moisture content, classification and particle size distribution) was collected to calibrate the model. Additional data was obtained from the Soil Research Institute in Ghana to explore calibration of the Universal Soil Loss Equation (USLE, Wischmeier and Smith, 1978) for Ghanaian soils and environment. It was shown that the USLE could be successfully converted to provide meaningful soil loss estimates in the Ghanaian environment. However, due to experimental difficulties, the proposed theory and methodology of the sediment yield model could only be tested in principle. Future work may include validation of the model and subsequent scaling up to estimate sedimentation rates in Lake Volta.

This thesis examines relations between the French Confederation Generale du Travail (CGT) and the labour movements of other countries in the years leading up to the First World War. The aim of the study is to examine the CGT's policy of internationalism in practice, both in relations with other labour movements and in its membership of the International Secretariat of National Trade Union Centres (between 1900 and 1914). In particular, the relationship between the French and German labour movements is explored in the light of the events of August 1914. This study shows that the relationship was a reflection of the respective positions of the French and German labour movements in the international movement. It also subjects to close scrutiny the assumption, widely made before 1914, that workers had more in common with each other than with the ruling classes of their own country, by analysing the extent of, and the reasons for internationalism and international cooperation in the labour movement. As a study of the International Secretariat of National Trade Union Centres, an organisation about which very little has previously been written, this thesis complements existing work on the international labour movement prior to 1914. It also provides new insights into the French CGT by concentrating on the fundamental areas of internationalism and opposition to war, and offers fresh contributions to the continuing debate on the international labour movement and its response to the outbreak of war.

This thesis describes the work carried out on the development of a novel digit actuator system with tactile perception feedback to a user and demonstrated as a master-slave system. For the tactile surface of the digit, contrasting sensor elements of resistive strain gauges and optical fibre Bragg grating sensors were evaluated. A distributive tactile sensing system consisting of optimised neural networking schemes was developed, resulting in taxonomy of artificial touch. The device is suitable for use in minimal invasive surgical (MIS) procedures as a steerable tip and a digit constructed wholly from polymers makes it suitable for use in Magnetic Resonance Imaging (MRI) environments enabling active monitoring of the patient during a procedure. To provide a realistic template of the work the research responded to the needs of two contrasting procedures: palpation of the prostate and endotracheal intubation in anaesthesia where the application of touch sense can significantly assist navigation. The performance of the approach was demonstrated with an experimental digit constructed for use in the laboratory in phantom trials. The phantom unit was developed to resemble facets of the clinical applications and digit system is able to evaluate reactive force distributions acting over the surface of the digit as well as different descriptions of contact and motion relative to the surface of the lumen. Completing control of the digit is via an instrumented glove, such that the digit actuates in sympathy with finger gesture and tactile information feedback is achieved by a combination of the tactile and visual means.

This thesis starts with a literature review, outlining the major issues identified in the literature concerning virtual manufacturing enterprise (VME) transformation. Then it details the research methodology used – a systematic approach for empirical research. next, based on the conceptual framework proposed, this thesis builds three modules to form a reference model, with the purpose of clarifying the important issues relevant to transforming a traditional manufacturing company into a VME. The first module proposes a mechanism of VME transformation – operating along the VME metabolism. The second module builds a management function within a VME to ensure a proper operation of the mechanism. This function helps identify six areas as closely related to VME transformation: lean manufacturing; competency protection; internal operation performance measurement; alliance performance measurement; knowledge management; alliance decision making. The third module continues and proposes an alliance performance measurement system which includes 14 categories of performance indicators. An analysis template for alliance decision making is also proposed and integrated into the first module. To validate these three modules, 7 manufacturing organisations (5 in China and 2 in the UK) were investigated, and these field case studies are analysed in this thesis. The evidence found in these organisations, together with the evidence collected from the literature, including both researcher views and literature case studies, provide support for triangulation evidence. In addition, this thesis identifies the strength and weakness patterns of the manufacturing companies within the theoretical niche of this research, and clarifies the relationships among some major research areas from the perspective of virtual manufacturing. Finally, the research findings are summarised, as well as their theoretical and practical implications. Research limitations and recommendations for future work conclude this thesis.

This thesis records the findings of a retrospective study of decompression illness (DCI) in the UK compressed air tunnelling industry since the mid-1980s. The thesis describes how the study arose, its scope and objectives, along with an overview of tunnelling and shaft-sinking. The development of compressed air working techniques is reviewed along with a description of decompression practice and DCI, and an outline of relevant legislation and guidance. The acquisition and manipulation of data to form a number of databases and spreadsheets on which the analysis was performed is discussed. That analysis examined measures of DCI incidence and quantified that incidence using these measures. Also considered is the variation in tolerance and susceptibility to DCI in the workforce, and the phenomenon of acclimatisation. An examination of the extent to which men worked on multiple contracts and the variation in their susceptibility to DCI on these contracts is included. The main conclusions are that a number of measures of DCI incidence were identified, some more appropriate than others and that the incidence of DCI when so measured was high, disproportionately so in shift workers. No reasonably practicable restrictions on exposure were identified which would have allowed the retention of air-only decompression. Oxygen decompression looked promising but had yet to be used sufficiently extensively to generate enough data for analysis. Recommendations included one that an alternative technique for monitoring the effectiveness of decompression should be developed. The thesis ends with recommendations for further research.