It is envisaged that flood plains will be put into more active usage to meet the increasing demands for road infrastructural development as well as relieve the pressure exerted on arable lands owing to infrastructural development activities. This is consequent upon the general shortfall in the availability of soils possessing the right engineering properties to carry infrastructures such as roads which consume large tracks of land. Expanding the global infrastructural base is inevitable due to the ever increasing human population and the need to meet their social, economic, political and transportation needs. However, owing to the prevailing environmental awareness campaigns fronted by different environmental agencies, there is the need to regulate and monitor the interaction of the processes involved in the provision of these needs with the limited resources as well as the environmental aftermath associated with such operations. The stabilization of flood plain soils for road embankment construction is envisaged to reduce the demand on the material resources required to build classical high embankments in flood prone areas as well as offer implied mitigating dimensions in the restoration of environmental integrity. This impliedly will reduce the use of traditionally unsustainable methods of soil stabilization such as, the excavation and importation of new materials, to a more robust system that will offer environmental friendliness amidst value engineering for better strength and durability results. The experimental processes involved the simulation of flooding scenarios in the laboratory, to monitor the strength and durability aspects of low-bearing-capacity soils (such as Lower Oxford Clay) stabilized with blended mixes of the traditional stabilizer of lime and the novel materials of lime and Ground Granulated Blastfumace Slag (GOBS) by-product combined. Preliminary investigations were carried out on the Lower Oxford Clay soil to establish the moisture and compaction requirements of the material. Different mix compositions were formulated by incrementally replacing the amount of lime in the system with GOBS. This was based on the premise that high stabilizer contents could offer better stabilization to flood susceptible geo-materials upon flooding. A high stabilizer level of 16% was therefore investigated. Regimes of different blending ratios were established as follows: 16%Lime-0%GGBS, 12%Lime-4%GGBS, 8%Lime-8%GGBS, 4%Lime-12%GGBS and 0%Lime-16%GGBS and tested at moisture contents of 23%, 28%, 33% and 38%. The two extremes 16%Lime-0%GGBS and 0%Lime-16GGBS were used as controls. A system of elimination based on strength criteria was employed, where only the 8%Lime- 8%GGBS and 4%Lime-12%GGBS mixtures were deemed fit to be investigated further to determine their resistance to challenging environmental factors of flooding. The test samples were cylindrical, measuring 50 mm in diameter and 100 mm long, and these were compacted using a static compaction apparatus to achieve Maximum Dry Density (MDD). Depending on the testing regime to be applied to a given specimen, a curing pattern was defined and samples were wrapped in cling film to minimise moisture losses. At the end of each curing period of 7, 14, 28, 56 and 90 days, one of the experimental procedures which ranged from Unconfined Compressive Strength, Water Absorption, Volume Stability, Permeability, Soaked Strength and Durability Index Assessment or Compressibility Assessment was carried out on the moist cured samples. Following these assessments, the 4%Lime-12%GGBS mix composition was appraised to have overall improved characteristics with the added benefit of reduced cost of material utilisation. Based on the available data, regression analyses were carried out and equations established for predicting the strength values of stabilized materials. Using these equations further extrapolations were made and the observable trends were those of the dependence of compressive strength on the age of moist curing and the compaction moisture contents at which samples were produced at given blended mixture. Cost-benefit-risk analysis was also carried out with a further cost annualisation of the capital and operational cost of a selected system. It is reassuring to learn that at replacement level of lime with GOBS of 4%Lime-12%GGBS it was possible to establish multi-binder mixtures that could be effectively used for sustainable construction in flood prone areas with enormous savings accruing from the possible higher strength and enhanced durability indices achievable over traditional unsustainable options of continued over-reliance on lime and Portland cement.

In-situ piezocone, flat dilatometer, and screw plate tests were carried out adjacent to the site of several large earth embankments, founded on a deep deposit of compressible soil. Settlement records since construction were available for two of the embankments. Geotechnical parameters were not back analyzed from the case record, rather, embankment performance was predicted on the basis of parameters interpreted from the in-situ tests alone. Consolidation characteristics were interpreted from the measurement of dissipation of excess pore pressures using the piezocone and dilatometer. Both devices provided complementary results in terms of an appropriate coefficient of consolidation. The excellent stratigraphic profile furnished by the piezocone (CPTU) tests proved to be a most valuable feature. The stratigraphic detail provided by the CPTU tests performed across the site identified continuous, free (framing soil layers which would generally be missed in a conventional geotechnical investigation using a drilled borehole with discrete sampling. The identification of these layers was of paramount importance in the prediction of settlement rate. A one-dimensional analysis formed the basis for the settlement predictions, and was found to be satisfactory. Settlement magnitudes were predicted within 10% of the observed measurements, parallelling the observed rate of settlement throughout the embankment construction period in the early 1970's and to the present date. Key words: settlement, deltaic soils, embankment, in-situ testing, piezocone, flat dilatometer, screw plate, coefficient of consolidation, compressibility, pore pressure dissipation. / Applied Science, Faculty of / Civil Engineering, Department of / Graduate

Thesis (MScEng (Civil Engineering))--University of Stellenbosch, 2005. / There has always been some debate in the past about the most effective and economical type of revetment to be used to combat or prevent erosion in rivers and channels. Some of the most common materials used for these mitigation measures are gabions, Reno mattresses and rip rap. A study done by the Colorado State University (CSU, 1984), comprised hydraulic tests of Reno mattresses used as a channel bed revetment. The result were compared with those of rip rap. This thesis mainly deals with the evaluation of incipient motion conditions for rock used in Reno mattresses and as rip rap. In this thesis the results of the CSU study and the design criteria of Maccaferri are evaluated and compared with the result obtained when applying the stream power theory and the Shields' theory with respect to incipient motion. This thesis includes the theory with respsect to incipient motion conditions, background to the CSU study and comparisons of the results of the CSU study and Maccaferri's design criteria with theoretical calculations. A cost comparison of Reno mattresses and rip rap as channel bed revetment measures, as well as conclusions and recommendations with regard to the design and use of these options, are also included. The frame of reference for this thesis is the set of CSU test results. The calibrations achieved, proposals made and accuracy of conclusions thus depend on those results.