This dissertation presents the analysis and development of an innovative semiconductor device and topology for the high power current source converter (CSC). The CSC is very attractive in high power applications due to its lower output dv/dt, easy regeneration capability and implicit short-circuit protection. Traditionally, either a symmetrical gate turn-off (GTO) thyritor or an asymmetrical GTO in series with a diode is used as the power switch in the CSC. Since the GTO has a lower switching speed and requires a complicated gate driver, the symmetrical GTO based CSC usually has low dynamic response speed and low efficiency. To achieve high power rating, fast dynamic response speed and low harmonics, an advanced semiconductor device and topology are needed for the CSC. Based on symmetrical GTO and power MOSFET technologies, a symmetrical emitter turn-off (ETO) thyristor is developed that shows superior switching performance, high power rating and reverse voltage blocking capability. The on-state characteristics, forced turn-on characteristics, forced turn-off characteristics and the load-commutated characteristics are studied. Test results show that although the load-commutation loss is high, the developed symmetrical ETO is suitable for use in high power CSC due to its low conduction loss, fast switching speed and reverse voltage blocking capability. The snubberless turn-on capability is preferred for a semiconductor device in a power conversion system, and can be achieved for devices with forward biased safe operation area (FBSOA). The FBSOA of the ETO is investigated and experimentally demonstrated. The ETO device has excellent FBSOA due to the negative feedback provided by the emitter switch. However, the FBSOA for a large area ETO is poor. A new ETO concept is therefore proposed for future development in order to demonstrate the FBSOA over a large area device. To improve the turn-on performance of the large area ETO, a novel concept, named the transistor-mode turn-on, is proposed and studied. During the transistor-mode turn-on process, the ETO behaves like a transistor instead of a thyristor. Without a snubber, the transistor-mode turn-on for the ETO is hard to achieve. Through the selection of a proper gate drive and di/dt snubber, the transistor-mode turn-on can be implemented, and the turn-on performance for the ETO can be dramatically improved. To increase the power rating of the CSC without degrading the utilization of power semiconductor devices, a novel multilevel CSC, named the parallel-cell multilevel CSC, is proposed. Based on a six-switch CSC cell, the parallel-cell multilevel CSC has the advantages of high power rating, low harmonics, fast dynamic response and modularity. Therefore, it is very suitable for high power applications. The power stage design, modeling, control and switching modulation scheme for a parallel-cell multilevel CSC based static var compensator (STATCOM) are analyzed and verified through simulation. / Ph. D.

Advancements in the power electronics systems have been directly related to the availability of improved power semiconductor devices. The device performance greatly determines the efficiency, reliability, volume, and cost of the power electronics system. This dissertation is dedicated to develop an advanced high power semiconductor device, the emitter turn-off (ETO) thyristor, which is targeted to improve the limitations of the present high power devices. Major improvements in electrical and mechanical designs of the ETO for high power and high frequency operation are proposed which result in improved snubberless turn-off capability, low conduction loss, and low gate drive power consumption of the new generation ETO. A revolutionary self-power generation method of the ETO is proposed. Different from the conventional high power devices which require the external power input for their gate drivers, ETO achieves complete optically controlled turn-on and turn-off and all the internal power required is self-generated. This advancement will have a major impact to high power converter designs. A novel integrated method to eliminate the dead-time requirement is proposed for ETO. This method not only improves the output waveform quality but also increases the reliability and reduces the cost of the high power PWM voltage source converters. With this unique function, the upper and the lower ETO's within a converter phase leg can receive the ideal complementary (without dead-time) PWM signals and solve shoot-through problems. Method to measure the ETO current and transfer the current information to a PWM signal is proposed. Based on the ETO's built-in current sensor, the over-current protection function of the ETO is designed as well. The experimental results show that the built-in current sensor has a very high precision, and the over-current protection function can effectively protect the ETO during the short circuit faults. In order to improve ETO's turn-off capability, a comprehensive investigation of the turn-off failure mechanism of the ETO was performed. A series of simulations and experiments are carried out to study the ETO turn-off operation. The detail turn-off failure mechanisms are presented. The conditions to cause the ETO failure are addressed. The approaches to improve the ETO's turn-off capability are discussed. / Ph. D.

This dissertation presents a systematic design and demonstration of a novel solid-state DC circuit breaker. The mechanical circuit breaker is widely used in power systems to protect industrial equipment during fault or abnormal conditions. Compared with the slow and high-maintenance mechanical circuit breaker, the solid-state circuit breaker is capable of high-speed interruption of high currents without generating an arc, hence it is maintenance-free. Both the switch and the tripping unit are solid-state, which meet the requirements of precise protection and high reliability. The major challenge in developing and adopting a solid-state circuit breaker has been the lack of power semiconductor switches that have adequate current-carrying capability and interruption capability. The high-speed, high-current solid-state DC circuit breaker proposed and demonstrated here uses a newly-emerging power semiconductor switch, the emitter turn-off (ETO) thyristor as the main interruption switch. In order to meet the requirement of being a high-current circuit breaker, ETO parallel operation is needed. Therefore the major effort of this dissertation is dedicated to the development of a high-current (5000A) DC switch module that utilizes multiple ETOs in parallel. This work can also be used to develop an AC switch module by changing the asymmetrical ETOs used to symmetrical ETOs. An accurate device model of the ETO is needed for the development of the high-current DC switch module. In this dissertation a novel physics-base lumped charge model is developed for the ETO thyristor for the first time. This model is verified experimentally and used for the research and development of the emitter turn-off (ETO) thyristor as well as the DC switch module discussed in this dissertation. With the aid of the developed device model, the device current sharing between paralleled multiple ETO thyristors is investigated. Current sharing is difficult to achieve for a thyristor-type device due to the large device parameter variations and strong positive feedback mechanism in a latched thyristor. The author proposes the "DirectETO" concept that directly benefits from the high-speed capability of the ETO and strong thermal couplings among ETOs. A high-current DC switch module based on the DirectETO can be realized by directly connecting ETOs in parallel without the bulky current sharing inductors used in other current-sharing solutions. In order to achieve voltage stress suppression under high current conditions, the parasitic parameters, especially parasitic inductance in a high-current ETO switch module are studied. The Partial Element Equivalent Circuit (PEEC) method is used to extract the parasitics. Combined with the developed device model, the electrical interactions among multiple ETOs are investigated which results in structural modification for the solid-state DC switch module. The electro-thermal model of the DC switch module and the heatsink subsystem is used to identify the "thermal runaway" phenomenon in the module that is caused by the negative temperature coefficient of the ETO's conduction drop. The comparative study of the electro-thermal coupling identifies a strongly-coupled thermal network that increases the stability of the thermal subsystem. The electro-thermal model is also used to calculate the DC and transient thermal limit of the DC switch module. The high-current (5000A) DC switch module coupled with a solid state tripping unit is successfully applied as a high-speed, high-current solid-state DC circuit breaker. The experimental demonstration of a 5000A current interruption shows an interruption time of about 5 microseconds. This high-speed, high-current DC switch module can therefore be used in DC circuit breaker applications as well as other types of application, such as AC circuit breakers, transfer switches and fault current limiters. Since the novel solid-state DC circuit breaker is able to extinguish the fault current even before it reaches an uncontrollable level, this feature provides a fast-acting, current-limiting protection scheme for power systems that is not possible with traditional circuit breakers. The potential impact on the power system is also discussed in this dissertation. / Ph. D.