A nanoparticle (NP) doping technique was used for making erbium-doped fibers (EDFs) for high energy lasers. The nanoparticles were doped into the silica soot of preforms, which were drawn into fibers. The Er luminescence lifetimes of the NP-doped cores are longer than those of corresponding solution-doped silica, and substantially less Al is incorporated into the NP-doped cores. Optical-to-optical slope efficiencies of greater than 71% have been measured. Initial investigations of stimulated Brillouin scattering (SBS) have indicated that SBS suppression is achieved by NP doping, where we observed a low intrinsic Brillouin gain coefficient, of similar to 1x 10(-11) m/W and the Brillouin bandwidth was increased by 2.5x compared to fused silica.

A tunable erbium-doped fiber ring laser using an intra-cavity Fabry-Perot filter as the tuning element is investigated. Tuning is achieved by varying the applied voltage which controls the FP cavity length. The laser's wavelength is monitored using an optical spectrum analyzer to determine the laser's spectral characteristics under static conditions at different wavelengths over its tuning range of approximately 50nm. When the laser is tuned rapidly, the frequency versus time characteristic is determined using a fiber Fabry-Perot interferometer with a photodetector to convert the optical signal to an electrical signal. The core of the research is to determine the degree of spectral broadening of the laser as a function of the spectral tuning rate. The fringe contrast of fiber Fabry-Perot interferometer transmittance curves decreases with increase in the tuning frequency. The gain at a certain wavelength becomes a function of time putting an upper limit on the tuning frequency of the system. The carrier lifetime of erbium ions dictates the maximum achievable tuning speed.

No description available.

This thesis presents a novel technique named "Core Suction" for fabricating optical fiber preforms for manufacturing highly doped fibers (HDFs) for optical amplification (Raman effect based or Erbium fiber based). The technique involves drawing the molten non-conventional core glass material into the silica cladding tube to form the preform. The developed technique is simple, inexpensive and shows great potential for fabricating preforms of highly nonlinear non-conventional multi-component glasses as the core material. Preforms were made with various core glasses such as Schott SF6, Lead-Tellurium-Germanate, Lead-Tellurium-Germanate- Neodymium -Erbium and MM2 in silica cladding tubes and then pulled into fibers. The fabricated fibers were measured for refractive index profile, loss spectrum and spontaneous Raman spectra. Elemental analysis of the fiber samples was also performed using an electron microprobe. Erbium doped fiber amplifiers (EDFAs) were setup using 30 cm, 5cm and 1 cm lengths of fabricated erbium doped fibers and their gain spectra measured. The distributed gain spectrum for an EDFA was also measured using an optical frequency domain reflectometery (OFDR) technique. Commercial dispersion compensated fiber (DCF) with very high GeO2 doping was used to setup a Raman amplifier and the gain spectrum measured. One of the needs of Raman amplification in optical fibers is to predict an accurate Raman gain, based on the fiber's refractive index profile. A method of predicting Raman gain in GeO2 doped fibers is presented and the predicted Raman gain values are compared with the measured ones in the same fibers. Raman gain issues like the dependence of the Raman gain on the GeO2 concentration, polarization dependence were taken into account for the gain calculations. An experimental setup for Raman gain measurements was made and measurement issues addressed. Polarization dependence of the Raman gain in one kilometer of polarization maintaining fiber was also measured. / Ph. D.

In recent years laser technology has increasingly developed with the use of fiber lasers and this has provided the possibility to implement different techniques in the defense industry. LADAR is at the forefront of these techniques. Fiber lasers constitute a perfect source for LADAR systems due to their excellent robustness, compact size and high-power generation capability. In this study we will explore the development of a pulsed fiber laser source for a LADAR system that can obtain high resolution 3D images in eye-safe region. A high power, all fiber integrated erbium system with strictly single mode operation in eye-safe region based on MOPA (master oscillator power amplifier) configuration with seed source and amplifier part was developed. Both the use of an actively mode locked laser with erbium doped fiber and fiber coupled modulated distributed feedback diode laser were investigated as seed sources for the amplifier part. Both erbium doped single clad fiber and erbium-ytterbium doped double clad gain fiber were used in this amplifier system. After amplification of the actively mode locked laser, 12 W of average optical power was obtained through single mode fiber with 1ns pulse duration at 10 MHz which corresponds to 1.2 kW peak power. For the fiber coupled DFB diode laser, 9.5W average power was obtained with around 8 ns duration pulses at 100 kHz and about 9.2 W average power was also obtained with around 700 ps duration pulses at 1 MHz through strictly single mode fiber at the output of the same amplifier system as was used in the actively mode locked seed source. In both cases calculated peak power was around 10 kW v which is estimated as the highest peak power for an all fiber integrated system with single mode operation. The development of such a fiber system with high power capability, compact size and free of misalignment is expected to be useful for LADAR application as well as other areas such as eye surgery, 3D silicon processing or any other material processing applications.

Master of Science / Department of Physics / Brian R. Washburn / This thesis reports our attempt towards achieving a phase stabilized free-space nonlinear polarization rotation (NPR) mode locked erbium doped fiber laser frequency comb system. Optical frequency combs generated by mode-locked femtosecond fiber lasers are vital tools for ultra-precision frequency metrology and molecular spectroscopy. However, the comb bandwidth and average output power become the two main limiting elements in the application of femtosecond optical frequency combs. We have specifically investigated the free-space mode locking dynamics of erbium-doped fiber (EDF) mode-locked ultrafast lasers via nonlinear polarization rotation (NPR) in the normal dispersion regime. To do so, we built a passively mode-locked fiber laser based on NPR with a repetition rate of 89 MHz producing an octave-spanning spectrum due to supercontinuum (SC) generation in highly nonlinear fiber (HNLF). Most significantly, we have achieved highly stable self-starting NPR mode-locked femtosecond fiber laser based frequency comb which has been running mode locked for the past one year without any need to redo the mode locking. By using the free-space NPR comb scheme, we have not only shortened the cavity length, but also have obtained 5 to 10 times higher output power (more than 30 mW at central wavelength of 1570 nm) and much broader spectral comb bandwidth (about 54 nm) compared to conventional all-fiber cavity structure with less than 1 mW average output power and only 10 nm spectral bandwidth. The pulse output from the NPR comb is amplified through a 1 m long EDF, then compressed by a length of anomalous dispersion fiber to a near transform limited pulse duration. The amplified transform limited pulse, with an average power of 180 mW and pulse duration of 70 fs, is used to generate a supercontinuum of 140 mW. SC generation via propagation in HNLF is optimized for specific polling period and heating temperature of PPLN crystal for SHG around 1030 nm. At last, we will also discuss the attempt of second harmonic generation (SHG) by quasi phase matching in the periodically polled lithium niobate (PPLN) crystal due to nonlinear effect corresponding to different polling period and heating temperature.

Os sistemas ópticos atuais, baseados em fibras monomodo, operam próximos ao limite teórico da capacidade. Sistemas ópticos baseados em multiplexação modal (Mode Division Multiplexing – MDM) possibilitam o aumento da capacidade do sistema por meio do uso de fibras de poucos modos. Nestes sistemas, a propriedade de ortogonalidade entre os modos propagantes permite que cada modo espacial carregue um sinal óptico específico. O amplificador à fibra dopada com érbio (Erbium-Doped Fiber Amplifier – EDFA) segue fundamental para assegurar a transmissão em longas distâncias. No entanto, devido às distintas distribuições de intensidade dos modos que compõem o sinal de entrada, cada modo experimenta diferentes valores de ganho. Desta forma, o objetivo principal no projeto de EDFAs de poucos modos (Few-Mode Erbium-Doped Fiber Amplifier – FM-EDFA) é determinar os melhores parâmetros opto-geométricos da fibra para produzir uma amplificação eficiente. A metodologia normalmente empregada é baseada na resolução das equações de taxa e de propagação. Nesta tese, é proposta uma metodologia alternativa de projeto de FM-EDFA, baseada em uma nova figura de mérito. Este parâmetro quantifica o nível de inversão da população dos íons na fibra a partir da integral de superposição (overlap integral), considerando tanto o perfil de dopagem da fibra dopada com érbio para poucos modos (Few-Mode Erbium-Doped Fiber – FM-EDF) quanto as distribuições de intensidade dos sinais de entrada e de bombeio. A aplicação desta metodologia permite reduzir, em cerca de 25-40 vezes, o número de resoluções das equações de taxa e de propagação e, consequentemente, diminuir o tempo de processamento e reduzir o esforço computacional. Como consequência da maior velocidade de processamento, torna-se possível a aplicação de métodos de otimização mais rigorosos, permitindo uma busca em um espaço irrestrito de soluções. Especificamente, a partir de uma metodologia baseada em algoritmos genéticos, obteve-se um perfil de dopagem otimizado. É também demonstrado que os perfis com geometria circular exibem melhores características, como excelente desempenho do FM-EDFA e maior facilidade de fabricação. Por meio da análise da figura de mérito, é mostrado que o desempenho do FM-EDFA é afetado pelas características do modo de bombeio. Finalmente, o desempenho de um sistema óptico MDM é avaliado, simulado por meio da integração entre as ferramentas MatLab® e VPItransmissionMakerTM, comprovando a necessidade do projeto de um amplificador específico para sistemas MDM. / Modern optical systems based on single-mode fiber, operate close to the theoretical capacity limit. By using few-mode fibers, optical systems based on modal division multiplexing (MDM) allows increased system capacity. In these systems, orthogonality between the propagating modes allows each spatial mode to carry a specific optical signal. The erbium doped fiber amplifier (EDFA) remains essential to ensure long distance transmission. However, due to the distinct intensity profile distributions of the modes which comprise the input signal, each mode experiences a different value of optical gain. Thus, the main objective in the few-mode EDFA design (FM-EDFA) is to determine the best opto-geometrical fiber parameters in order to produce an efficient amplification. The methodology normally used is based on the simultaneous resolution of the rate and propagation equations. In this thesis, we propose an alternative methodology for the FM-EDFA design, based on a new figure of merit which quantifies the level of population inversion for the Er ions in the fiber, by means of a overlap integral considering both the doping profile of the few-mode erbium doped fiber (FM-EDF) as well as the intensity distributions of the optical signals and pump beams. This methodology reduces, by a factor of 25-40, the number of resolutions of the rate and propagation equations, thereby decreasing processing time and computational effort. As a consequence of the improved processing speed, it becomes possible to apply more rigorous optimization methods in an unrestricted solution space. Specifically, by using a genetic algorithm technique, we obtained an optimized doping profile. It is also shown that profiles with circular geometry exhibit improved features, such as excellent FM-EDFA performance and ease of manufacturing. By analyzing the figure of merit, it is shown that the FM-EDFA performance is affected by the characteristics of the pump mode. Finally, the performance of an MDM optical system is evaluated, by integrating Matlab and VPI simulation tools, to demonstrate the need for specific amplifier designs in MDM systems.

Made available in DSpace on 2016-12-12T20:15:48Z (GMT). No. of bitstreams: 1 elementos pre-textuais.pdf: 162361 bytes, checksum: 82f1f3cdfd0bb7d2b36c65252dee4600 (MD5) Previous issue date: 2012-02-24 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / The erbium-doped fiber dual-ring laser is a four-dimensional continuous-time dynamical system, modeled by a set of four autonomous, first-order ordinary differential equations, and has been investigated in the last years due to several applications, as an example, chaos control, chaos synchronization and telecommunications systems. In this work we study the nonlinear dynamics of an erbium-doped fiber dual-ring laser from two points of view, analytical and numerical. The analytical investigation consists in to analyse the stability of an equilibrium point, using the Routh-Hurwitz criterion and some eigenvalues of the Jacobian matrix. The numerical investigation was performed in a the two-dimensional parameter-space of a set autonomous, seven-parameter, four-dimensional first-order ordinary differential equation system, tuning two parameters that control the dynamics. By using the Lyapunov exponents spectrum as a measure of chaotic and periodic behaviors, we construct parameter-space diagrams to characterize the dynamics of the model. We study the self-organized periodic structures embedded in a chaotic region by means of bifurcation diagrams, showing that there are directions in two-dimensional parameter-spaces in which the periodic structures are arranged in period-adding bifurcation cascades. / O laser de fibra de dois anéis dopado a érbio é um sistema dinâmico quadridimensional a tempo contínuo, modelado por um conjunto de quatro equações diferenciais ordinárias de primeira ordem autônomas, e tem sido investigado nos últimos anos devido as diversas aplicações, como por exemplo, controle de caos, sincronização de caos e sistemas de telecomunicações. Neste trabalho estudamos a dinâmica não linear do laser de fibra de dois anéis dopado a érbio a partir de dois pontos de vista, analítico e numérico. A investigação analítica consiste em analisar a estabilidade de um ponto de equilíbrio do sistema, usando o critério de Routh-Hurwitz e alguns autovalores da matriz Jacobiana. A investigação numérica foi realizada em um espaço de parâmetros bidimensional de um conjunto de quatro equações diferencias ordinárias de primeira ordem autônomas com sete parâmetros, variando dois parâmetros que controlam a dinâmica. Usando o maior Expoente de Lyapunov como uma medida dos comportamentos caótico e periódico construímos diagramas do espaço de parâmetros para caracterizar a dinâmica do modelo. Estudamos as auto-organizações de estruturas periódicas imersas em uma região caótica usando diagramas de bifurcação, mostrando que existem direções específicas no espaço de parâmetros bidimensional em que tais estruturas periódicas são arranjadas em cascatas de bifurcação por adição de período.

Os sistemas ópticos atuais, baseados em fibras monomodo, operam próximos ao limite teórico da capacidade. Sistemas ópticos baseados em multiplexação modal (Mode Division Multiplexing – MDM) possibilitam o aumento da capacidade do sistema por meio do uso de fibras de poucos modos. Nestes sistemas, a propriedade de ortogonalidade entre os modos propagantes permite que cada modo espacial carregue um sinal óptico específico. O amplificador à fibra dopada com érbio (Erbium-Doped Fiber Amplifier – EDFA) segue fundamental para assegurar a transmissão em longas distâncias. No entanto, devido às distintas distribuições de intensidade dos modos que compõem o sinal de entrada, cada modo experimenta diferentes valores de ganho. Desta forma, o objetivo principal no projeto de EDFAs de poucos modos (Few-Mode Erbium-Doped Fiber Amplifier – FM-EDFA) é determinar os melhores parâmetros opto-geométricos da fibra para produzir uma amplificação eficiente. A metodologia normalmente empregada é baseada na resolução das equações de taxa e de propagação. Nesta tese, é proposta uma metodologia alternativa de projeto de FM-EDFA, baseada em uma nova figura de mérito. Este parâmetro quantifica o nível de inversão da população dos íons na fibra a partir da integral de superposição (overlap integral), considerando tanto o perfil de dopagem da fibra dopada com érbio para poucos modos (Few-Mode Erbium-Doped Fiber – FM-EDF) quanto as distribuições de intensidade dos sinais de entrada e de bombeio. A aplicação desta metodologia permite reduzir, em cerca de 25-40 vezes, o número de resoluções das equações de taxa e de propagação e, consequentemente, diminuir o tempo de processamento e reduzir o esforço computacional. Como consequência da maior velocidade de processamento, torna-se possível a aplicação de métodos de otimização mais rigorosos, permitindo uma busca em um espaço irrestrito de soluções. Especificamente, a partir de uma metodologia baseada em algoritmos genéticos, obteve-se um perfil de dopagem otimizado. É também demonstrado que os perfis com geometria circular exibem melhores características, como excelente desempenho do FM-EDFA e maior facilidade de fabricação. Por meio da análise da figura de mérito, é mostrado que o desempenho do FM-EDFA é afetado pelas características do modo de bombeio. Finalmente, o desempenho de um sistema óptico MDM é avaliado, simulado por meio da integração entre as ferramentas MatLab® e VPItransmissionMakerTM, comprovando a necessidade do projeto de um amplificador específico para sistemas MDM. / Modern optical systems based on single-mode fiber, operate close to the theoretical capacity limit. By using few-mode fibers, optical systems based on modal division multiplexing (MDM) allows increased system capacity. In these systems, orthogonality between the propagating modes allows each spatial mode to carry a specific optical signal. The erbium doped fiber amplifier (EDFA) remains essential to ensure long distance transmission. However, due to the distinct intensity profile distributions of the modes which comprise the input signal, each mode experiences a different value of optical gain. Thus, the main objective in the few-mode EDFA design (FM-EDFA) is to determine the best opto-geometrical fiber parameters in order to produce an efficient amplification. The methodology normally used is based on the simultaneous resolution of the rate and propagation equations. In this thesis, we propose an alternative methodology for the FM-EDFA design, based on a new figure of merit which quantifies the level of population inversion for the Er ions in the fiber, by means of a overlap integral considering both the doping profile of the few-mode erbium doped fiber (FM-EDF) as well as the intensity distributions of the optical signals and pump beams. This methodology reduces, by a factor of 25-40, the number of resolutions of the rate and propagation equations, thereby decreasing processing time and computational effort. As a consequence of the improved processing speed, it becomes possible to apply more rigorous optimization methods in an unrestricted solution space. Specifically, by using a genetic algorithm technique, we obtained an optimized doping profile. It is also shown that profiles with circular geometry exhibit improved features, such as excellent FM-EDFA performance and ease of manufacturing. By analyzing the figure of merit, it is shown that the FM-EDFA performance is affected by the characteristics of the pump mode. Finally, the performance of an MDM optical system is evaluated, by integrating Matlab and VPI simulation tools, to demonstrate the need for specific amplifier designs in MDM systems.

Made available in DSpace on 2016-03-15T19:37:34Z (GMT). No. of bitstreams: 1 Claudia Barros dos Santos.pdf: 3294972 bytes, checksum: b848d69d9c6a8c824e5142a4e3659d37 (MD5) Previous issue date: 2011-01-21 / In this work, we inserted two Arrayed Waveguide Gratings (AWGs), in an Erbium doped fiber ring cavity laser, where a single gain medium at room temperature can emit laser in multiples wavelengths, simultaneous and individualy controlled. The setup allowed us to check different functions in the ring cavity. Here we show emission in CW regime, Passive Mode-Locking, using Carbon Nanotubes as saturable absorbers and finally Active mode-locking at 7GHz, simultaneously. / Neste trabalho, fez-se a inserção de duas grades de difração matriciais com guias de onda, ou AWGs (Arrayed Waveguide Gratings) em uma cavidade laser de fibra dopada com Érbio, onde um único meio de ganho em temperatura ambiente pode gerar ação laser em múltiplos comprimentos de onda, com emissões simultâneas e controladas individualmente. A configuração utilizada permitiu o teste com diferentes regimes de operação simultâneos dentro da cavidade. Mostramos a possibilidade de emissão laser em regime CW, em regime de mode-locking passivo, com o uso de nanotubos de carbono como absorvedor saturável e, por último, em regime de modelocking ativo com uma freqüência de modulação de 7 GHz.