Adhesively bonded joints have been investigated for several decades. In most analytical studies, the Bernoulli-Euler beam theory is employed to describe the behaviour of adherends. In the current work, three analytical models are developed for adhesively bonded joints using the Timoshenko beam theory for elastic material and a Bernoulli-Euler beam model for viscoelastic materials. One model is for the peeling test of an adhesively bonded joint, which is described using a Timoshenko beam on an elastic foundation. The adherend is considered as a Timoshenko beam, while the adhesive is taken to be a linearly elastic foundation. Three cases are considered: (1) only the normal stress is acting (mode I); (2) only the transverse shear stress is present (mode II); and (3) the normal and shear stresses co-exist (mode III) in the adhesive. The governing equations are derived in terms of the displacement and rotational angle of the adherend in each case. Analytical solutions are obtained for the displacements, rotational angle, and stresses. Numerical results are presented to show the trends of the displacements and rotational angle changing with geometrical and loading conditions. In the second model, the peeling test of an adhesively bonded joint is represented using a viscoelastic Bernoulli-Euler beam on an elastic foundation. The adherend is considered as a viscoelastic Bernoulli-Euler beam, while the adhesive is taken to be a linearly elastic foundation. Two cases under different stress history are considered: (1) only the normal stress is acting (mode I); and (2) only the transverse shear stress is present (mode II). The governing equations are derived in terms of the displacements. Analytical solutions are obtained for the displacements. The numerical results show that the deflection increases as time and temperature increase. The third model is developed using a symmetric composite adhesively bonded joint. The constitutive and kinematic relations of the adherends are derived based on the Timoshenko beam theory, and the governing equations are obtained for the normal and shear stresses in the adhesive layer. The numerical results are presented to reveal the normal and shear stresses in the adhesive.

Sandwich constructions are the most commonly used structures in aircraft and navy industries, traditionally. These structures are made up of the face sheets and the core, where the face sheets will be taking the load and is connected to other structural members, while the soft core material, will be used to absorb energy during impact like situation. Thus, sandwich constructions are mainly employed in light weight structures where the high energy absorption capability is required. Generally the face sheets will be thin, made up of either metallic or composite material with high stiffness and strength, while the core is light in weight, made up of soft material. Cores generally play very crucial role in achieving the desired properties of sandwich structures, either through geometric arrangement or material properties or both. Foams are in extensive use nowadays as core material due to the ease in manufacturing and their low cost. They are extensively used in automotive and industrial field applications as the desired foam density can be fabricated by adjusting the mixing, curing and heat sink processes. Modeling of sandwich beams play a crucial role in their design with suitable finite elements for face sheets and core, to ensure the compatibility between degrees of freedom at the interfaces. Unless the mathematical model simulates the physics of the model in terms of kinematics, boundary and loading conditions, results predicted will not be accurate. Accurate models helps in obtaining an efficient design of sandwich beams. In Structural Health Monitoring studies, the responses under the impact loading will be captured by carrying out the wave propagation analysis. The loads applied will be for a shorter duration (in the orders of micro seconds), where higher frequency modes will be excited. Wavelengths at such high frequencies are very small and hence, in such cases, very fine mesh generally is employed matching the wavelength requirement of the propagating wave. Traditional Finite element softwares takes enormous time and computational e ort to provide the solution. Various possible models and modeling aspects using the existing Finite element tools for wave propagation analysis are studied in the present work. There exists a huge demand for an accurate, efficient and rapidly convergent finite elements for the analysis of sandwich beams. E orts are made in the present work to address these issues and provide a solution to the sandwich user community. Super convergent and Spectral Finite sandwich Beam Elements with metallic or composite face sheets and soft core are developed. As a philosophy, the sandwich beam finite element is constructed with the combination of two beams representing the face sheets (top and bottom) at their neutral axis. The core effects are captured at the interface boundaries in terms of shear stress and normal transverse stress. In the case of wave propagation analysis, the equations are coupled in time domain and spatial domain and solving them directly is a difficult task. In Spectral Finite Element Method(SFEM), the displacement functions are derived by solving the transformed governing equations in the frequency domain. By transforming them and forces from time domain to frequency domain, the coupled partial differential equations will become coupled ordinary differential equations. These equations in frequency domain, can be solved exactly as they are normally ordinary differential equation with constant coefficients with frequency entering as a parameter. These solutions will be used as interpolating functions for spectral element formulation and in this respect it differs from conventional FE method wherein mostly polynomials are used as interpolating functions. In addition, SFEM solutions are expressed in terms of forward and backward moving waves for all the degrees of freedom involved in the formulations and hence, SFEM provides faster and efficient solutions for wave propagation analysis. In the present work, strong form of the governing differential equations are derived for a given system using Hamilton's principle. Super Convergent elements are developed by solving the static part of the governing differential equations exactly and hence the stiffness matrix derived is exact for point static loads. For wave propagation analysis, as the mass is not exactly represented, these elements are required in the optimal numbers for getting good results. The number of these elements required are generally much lesser than the number of elements required using traditional finite elements since the stiffness distribution is exact. Spectral elements are developed by solving the governing equations exactly in the frequency domain and hence the dynamic stiffness matrix derived is exact for the dynamic loads. Hence, one element between any two joints is enough to solve the whole system under impact loads for simple structures. Developing FE for sandwich beams is quiet challenging. Due to small thickness, the face sheets can be modeled using 1D idealization, while modeling of large core requires 2-D idealization. Hence, most finite or spectral elements requires stitching of these two idealizations into 1-D idealization, which can be accomplished in a variety of ways, some of which are highlighted in this thesis. Variety of finite and spectral finite elements are developed considering Euler and Timoshenko beam theories for modeling the sandwich beams. Simple element models are built with rigid core in both the theories. Models are also developed considering the flexible core with the variation of transverse displacements across depth of the core. This has direct influence on shear stress variation and also transverse normal stress in the core. Simple to higher order models are developed considering different variations in shear stress and transverse normal stress across depth of the core. Development of super convergent finite Euler Bernoulli beam elements Eul4d (4 dof element), Eul10d (10 dof element) are explained along with their results in Chapter 2. Development of different super convergent finite Timoshenko beam elements namely Tim4d (4 dof), Tim7d (7 dof), Tim10d (10 dof) are explained in Chapter 3. Validation of Euler Bernoulli and Timoshenko elements developed in the present work is carried out with test cases available in the open literature for displacements and free vibration frequencies are presented in Chapter 2 and Chapter 3. The results indicates that all developed elements are performing exceedingly well for static loads and free vibration. Super convergence performance for the elements developed is demonstrated with related examples. Spectral elements based on Timoshenko theory STim7d, STim6d, STim6dF are developed and the wave propagation characteristics studies are presented in Chapter 4. Euler spectral elements are derived from Timoshenko spectral elements by enforcing in finite shear rigidity, designated as SEul7d, SEul6d, SEul6dF and are presented. E orts were made in this present work to model the horizontal cracks in top or bottom face sheets using the spectral elements and the methodology is presented in Chapter 4. Wave propagation analysis using general purpose software N AST RAN and the super convergent as well as spectral elements developed in this work, are discussed in detail in Chapter 5. Modeling aspects of sandwich beam in N AST RAN using various combination of elements available and the performance of four possible models simulated were studied. Validation of all four models in N AST RAN, Super convergent Euler, Timoshenko and Spectral Timoshenko finite elements was carried out by simulating a homogenous I beam by comparing the longitudinal and transverse responses. Studies were carried out to find out the response predictions of a sandwich beam with soft core and all the predictions were compared and discussed. The responses in case of cracks in top or bottom face sheets under the longitudinal and transverse loading were studied in this chapter. In Chapter 6, Parametric studies were carried out for bringing out the sensitiveness of the important specific parameters in overall behaviour and performance of a sandwich beam, using Super convergent and Spectral elements developed. This chapter clearly brings out the various aspects of design of sandwich beam such as material selection of core, geometrical configuration of overall beam and core. Effects of shear modulus, mass density on wave propagation characteristics, effects of thick or thin cores with reference to the face sheets and dynamic effects of core are highlighted. Wave propagation characteristics studies includes the study of wave numbers, group speeds, cut off frequencies for a given configuration and identification of frequency zone of operations. The recommendations for improvement in design of sandwich beams based on the parametric studies are made at the end of chapter. The entire thesis, written in seven Chapters, presents a unified treatment of sandwich beam analysis that will be very useful for designers working in the area.

A control metric, the weighted sum of spatial gradients (WSSG), has been developed for use in active structural acoustic control (ASAC). Previous development of WSSG [1] showed that it was an effective control metric on simply supported plates, while being simpler to measure than other control metrics, such as volume velocity. The purpose of the current work is to demonstrate that the previous research can be generalized to plates with a wider variety of boundary conditions and on less ideal plates. Two classes of plates have been considered: clamped flat plates, and ribbed plates. On clamped flat plates an analytical model has been developed for use in WSSG that assumes the mode shapes are the product of clamped-clamped beam mode shapes. The boundary condition specific weights for use in WSSG have been derived from this formulation and provide a relatively uniform measurement field, as in the case of the simply supported plate. Using this control metric, control of radiated sound power has been simulated. The results show that WSSG provides comparable control to volume velocity on the clamped plate. Results also show, through random placement of the sensors on the plate, that similar control can be achieved regardless of sensor location. This demonstrates that WSSG is an effective control metric on a variety of boundary conditions. Ribbed plates were considered because of their wide use in aircraft and ships. In this case, a finite-element model of the plate has been used to obtain the displacement field on the plate under a variety of boundary conditions. Due to the discretized model involved, a numerical, as opposed to analytical, formulation for WSSG has been developed. Simulations using this model show that ASAC can be performed effectively on ribbed plates. In particular WSSG was found to perform comparable to or better than volume velocity on all boundary conditions examined. The sensor insensitivity property was found to hold within each section (divided by the ribs) of the plate, a slightly modified form of the flat plate insensitivity property where the plates have been shown to be relatively insensitive to sensor location over the entire surface of the plate. Improved control at natural frequencies can be achieved by applying a second control force. This confirms that ASAC is a viable option for the control of radiated sound power on non-ideal physical systems similar to ribbed plates.