Spelling suggestions: "subject:"eulerianlagrangian approach"" "subject:"eulerianlagrangian approach""
1 |
A Numerical Study of the Gas-Particle Flow in Pipework and Flow Splitting Devices of Coal-Fired Power PlantSchneider, Helfried, Frank, Thomas, Pachler, Klaus, Bernert, Klaus 17 April 2002 (has links) (PDF)
In power plants using large utility coal-fired boilers for generation of electricity the coal is pulverised in coal mills and then it has to be pneumatically transported and distributed to a larger number of burners (e.g. 30-40) circumferentially arranged in several rows around the burning chamber of the boiler. Besides the large pipework flow splitting devices are necessary for distribution of an equal amount of pulverised fuel (PF) to each of the burners. So called trifurcators (without inner fittings or guiding vanes) and ''riffle'' type bifurcators are commonly used to split the gas-coal particle flow into two or three pipes/channels with an equal amount of PF mass flow rate in each outflow cross section of the flow splitting device. These PF flow splitting devices are subject of a number of problems. First of all an uneven distribution of PF over the burners of a large utility boiler leads to operational and maintenance problems, increased level of unburned carbon and higher rates of NOX emissions. Maldistribution of fuel between burners caused by non uniform concentration of the PF (particle roping) in pipe and channel bends prior to flow splitting devices leads to uncontrolled differences in the fuel to air ratio between burners. This results in localised regions in the furnace which are fuel rich, where insufficient air causes incomplete combustion of the fuel. Other regions in the furnace become fuel lean, forming high local concentrations of NOX due to the high local concentrations of O2. Otherwise PF maldistribution can impact on power plant maintenance in terms of uneven wear on PF pipework, flow splitters as well as the effects on boiler panels (PF deposition, corrosion, slagging).
In order to address these problems in establishing uniform PF distribution over the outlet cross sections of flow splitting devices in the pipework of coal-fired power plants the present paper deals with numerical prediction and analysis of the complex gas and coal particle (PF) flow through trifurcators and ''riffle'' type bifurcators. The numerical investigation is based on a 3-dimensional Eulerian- Lagrangian approach (MISTRAL/PartFlow-3D) developed by Frank et al. The numerical method is capable to predict isothermal, incompressible, steady gas- particle flows in 3-dimensional, geometrically complex flow geometries using boundary fitted, block-structured, numerical grids. Due to the very high numerical effort of the investigated gas-particle flows the numerical approach has been developed with special emphasis on efficient parallel computing on clusters of workstations or other high performance computing architectures. Besides the aerodynamically interaction between the carrier fluid phase and the PF particles the gas-particle flow is mainly influenced by particle-wall interactions with the outer wall boundaries and the inner fittings and guiding vanes of the investigated flow splitting devices. In order to allow accurate quantitative prediction of the motion of the disperse phase the numerical model requires detailed information about the particle-wall collision process. In commonly used physical models of the particle-wall interaction this is the knowledge or experimental prediction of the restitution coefficients (dynamic friction coefficient, coefficient of restitution) for the used combination of particle and wall material, e.g. PF particles on steel.
In the present investigation these parameters of the particle-wall interaction model have been obtained from special experiments in two test facilities. Basic experiments to clarify the details of the particle-wall interaction process were made in a test facility with a spherical disk accelerator. This test facility furthermore provides the opportunity to investigate the bouncing process under normal pressure as well as under vacuum conditions, thus excluding aerodynamically influences on the motion of small particles in the near vicinity of solid wall surfaces (especially under small angles of attack). In this experiments spherical glass beads were used as particle material. In a second test facility we have investigated the real impact of non-spherical pulverised fuel particles on a steel/ceramic target. In this experiments PF particles were accelerated by an injector using inert gas like e.g. CO2 or N2 as the carrier phase in order to avoid dust explosion hazards. The obtained data for the particle-wall collision models were compared to those obtained for glass spheres, where bouncing models are proofed to be valid. Furthermore the second test facility was used to obtain particle erosion rates for PF particles on steel targets as a function of impact angles and velocities.
The results of experimental investigations has been incorporated into the numerical model. Hereafter the numerical approach MISTRAL/PartFlow-3D has been applied to the PF flow through a ''riffle'' type bifurcator. Using ICEM/CFD-Hexa as grid generator a numerical mesh with approximately 4 million grid cells has been designed for approximation of the complex geometry of the flow splitting device with all its interior fittings and guiding vanes. Based on a predicted gas flow field a large number of PF particles are tracked throughout the flow geometry of the flow-splitter. Besides mean quantities of the particle flow field like e.g. local particle concentrations, mean particle velocities, distribution of mean particle diameter, etc. it is now possible to obtain information about particle erosion on riffle plates and guiding vanes of the flow splitting device. Furthermore the influence of different roping patterns in front of the flow splitter on the uniformness of PF mass flow rate splitting after the bifurcator has been investigated numerically.
Results show the efficient operation of the investigated bifurcator in absence of particle roping, this means under conditions of an uniform PF particle concentration distribution in the inflow cross section of the bifurcator. If particle roping occurs and particle concentration differs over the pipe cross section in front of the bifurcator the equal PF particle mass flow rate splitting can be strongly deteriorated in dependence on the location and intensity of the particle rope or particle concentration irregularities. The presented results show the importance of further development of efficient rope splitting devices for applications in coal-fired power plants. Numerical analysis can be used as an efficient tool for their investigation and further optimisation under various operating and flow conditions.
|
2 |
Simulation of Unsteady Gas-Particle Flows including Two-way and Four-way Coupling on a MIMD Computer ArchitecturPachler, Klaus, Frank, Thomas, Bernert, Klaus 17 April 2002 (has links) (PDF)
The transport or the separation of solid particles or droplets suspended in a fluid flow is a common task in mechanical and process engineering. To improve machinery and physical processes (e.g. for coal combustion, reduction of NO_x and soot) an optimization of complex phenomena by simulation applying the fundamental conservation equations is required. Fluid-particle flows are characterized by the ratio of density of the two phases gamma=rho_P/rho_F, by the Stokes number St=tau_P/tau_F and by the loading in terms of void and mass fraction.
Those numbers (Stokes number, gamma) define the flow regime and which relevant forces are acting on the particle. Dependent on the geometrical configuration the particle-wall interaction might have a heavy impact on the mean flow structure. The occurrence of particle-particle collisions becomes also more and more important with the increase of the local void fraction of the particulate phase. With increase of the particle loading the interaction with the fluid phase can not been neglected and 2-way or even 4-way coupling between the continous and disperse phases has to be taken into account.
For dilute to moderate dense particle flows the Euler-Lagrange method is capable to resolve the main flow mechanism. An accurate computation needs unfortunately a high number of numerical particles (1,...,10^7) to get the reliable statistics for the underlying modelling correlations. Due to the fact that a Lagrangian algorithm cannot be vectorized for complex meshes the only way to finish those simulations in a reasonable time is the parallization applying the message passing paradigma.
Frank et al. describes the basic ideas for a parallel Eulererian-Lagrangian solver, which uses multigrid for acceleration of the flow equations. The performance figures are quite good, though only steady problems are tackled. The presented paper is aimed to the numerical prediction of time-dependend fluid-particle flows using the simultanous particle tracking approach based on the Eulerian-Lagrangian and the particle-source-in-cell (PSI-Cell) approach. It is shown in the paper that for the unsteady flow prediction efficiency and load balancing of the parallel numerical simulation is an even more pronounced problem in comparison with the steady flow calculations, because the time steps for the time integration along one particle trajectory are very small per one time step of fluid flow integration and so the floating point workload on a single processor node is usualy rather low.
Much time is spent for communication and waiting time of the processors, because for cold flow particle convection not very extensive calculations are necessary. One remedy might be a highspeed switch like Myrinet or Dolphin PCI/SCI (500 MByte/s), which could balance the relative high floating point performance of INTEL PIII processors and the weak capacity of the Fast-Ethernet communication network (100 Mbit/s) of the Chemnitz Linux Cluster (CLIC) used for the presented calculations. Corresponding to the discussed examples calculation times and parallel performance will be presented. Another point is the communication of many small packages, which should be summed up to bigger messages, because each message requires a startup time independently of its size. Summarising the potential of such a parallel algorithm, it will be shown that a Beowulf-type cluster computer is a highly competitve alternative to the classical main frame computer for the investigated Eulerian-Lagrangian simultanous particle tracking approach.
|
3 |
A Numerical Study of the Gas-Particle Flow in Pipework and Flow Splitting Devices of Coal-Fired Power PlantSchneider, Helfried, Frank, Thomas, Pachler, Klaus, Bernert, Klaus 17 April 2002 (has links)
In power plants using large utility coal-fired boilers for generation of electricity the coal is pulverised in coal mills and then it has to be pneumatically transported and distributed to a larger number of burners (e.g. 30-40) circumferentially arranged in several rows around the burning chamber of the boiler. Besides the large pipework flow splitting devices are necessary for distribution of an equal amount of pulverised fuel (PF) to each of the burners. So called trifurcators (without inner fittings or guiding vanes) and ''riffle'' type bifurcators are commonly used to split the gas-coal particle flow into two or three pipes/channels with an equal amount of PF mass flow rate in each outflow cross section of the flow splitting device. These PF flow splitting devices are subject of a number of problems. First of all an uneven distribution of PF over the burners of a large utility boiler leads to operational and maintenance problems, increased level of unburned carbon and higher rates of NOX emissions. Maldistribution of fuel between burners caused by non uniform concentration of the PF (particle roping) in pipe and channel bends prior to flow splitting devices leads to uncontrolled differences in the fuel to air ratio between burners. This results in localised regions in the furnace which are fuel rich, where insufficient air causes incomplete combustion of the fuel. Other regions in the furnace become fuel lean, forming high local concentrations of NOX due to the high local concentrations of O2. Otherwise PF maldistribution can impact on power plant maintenance in terms of uneven wear on PF pipework, flow splitters as well as the effects on boiler panels (PF deposition, corrosion, slagging).
In order to address these problems in establishing uniform PF distribution over the outlet cross sections of flow splitting devices in the pipework of coal-fired power plants the present paper deals with numerical prediction and analysis of the complex gas and coal particle (PF) flow through trifurcators and ''riffle'' type bifurcators. The numerical investigation is based on a 3-dimensional Eulerian- Lagrangian approach (MISTRAL/PartFlow-3D) developed by Frank et al. The numerical method is capable to predict isothermal, incompressible, steady gas- particle flows in 3-dimensional, geometrically complex flow geometries using boundary fitted, block-structured, numerical grids. Due to the very high numerical effort of the investigated gas-particle flows the numerical approach has been developed with special emphasis on efficient parallel computing on clusters of workstations or other high performance computing architectures. Besides the aerodynamically interaction between the carrier fluid phase and the PF particles the gas-particle flow is mainly influenced by particle-wall interactions with the outer wall boundaries and the inner fittings and guiding vanes of the investigated flow splitting devices. In order to allow accurate quantitative prediction of the motion of the disperse phase the numerical model requires detailed information about the particle-wall collision process. In commonly used physical models of the particle-wall interaction this is the knowledge or experimental prediction of the restitution coefficients (dynamic friction coefficient, coefficient of restitution) for the used combination of particle and wall material, e.g. PF particles on steel.
In the present investigation these parameters of the particle-wall interaction model have been obtained from special experiments in two test facilities. Basic experiments to clarify the details of the particle-wall interaction process were made in a test facility with a spherical disk accelerator. This test facility furthermore provides the opportunity to investigate the bouncing process under normal pressure as well as under vacuum conditions, thus excluding aerodynamically influences on the motion of small particles in the near vicinity of solid wall surfaces (especially under small angles of attack). In this experiments spherical glass beads were used as particle material. In a second test facility we have investigated the real impact of non-spherical pulverised fuel particles on a steel/ceramic target. In this experiments PF particles were accelerated by an injector using inert gas like e.g. CO2 or N2 as the carrier phase in order to avoid dust explosion hazards. The obtained data for the particle-wall collision models were compared to those obtained for glass spheres, where bouncing models are proofed to be valid. Furthermore the second test facility was used to obtain particle erosion rates for PF particles on steel targets as a function of impact angles and velocities.
The results of experimental investigations has been incorporated into the numerical model. Hereafter the numerical approach MISTRAL/PartFlow-3D has been applied to the PF flow through a ''riffle'' type bifurcator. Using ICEM/CFD-Hexa as grid generator a numerical mesh with approximately 4 million grid cells has been designed for approximation of the complex geometry of the flow splitting device with all its interior fittings and guiding vanes. Based on a predicted gas flow field a large number of PF particles are tracked throughout the flow geometry of the flow-splitter. Besides mean quantities of the particle flow field like e.g. local particle concentrations, mean particle velocities, distribution of mean particle diameter, etc. it is now possible to obtain information about particle erosion on riffle plates and guiding vanes of the flow splitting device. Furthermore the influence of different roping patterns in front of the flow splitter on the uniformness of PF mass flow rate splitting after the bifurcator has been investigated numerically.
Results show the efficient operation of the investigated bifurcator in absence of particle roping, this means under conditions of an uniform PF particle concentration distribution in the inflow cross section of the bifurcator. If particle roping occurs and particle concentration differs over the pipe cross section in front of the bifurcator the equal PF particle mass flow rate splitting can be strongly deteriorated in dependence on the location and intensity of the particle rope or particle concentration irregularities. The presented results show the importance of further development of efficient rope splitting devices for applications in coal-fired power plants. Numerical analysis can be used as an efficient tool for their investigation and further optimisation under various operating and flow conditions.
|
4 |
Simulation of Unsteady Gas-Particle Flows including Two-way and Four-way Coupling on a MIMD Computer ArchitecturPachler, Klaus, Frank, Thomas, Bernert, Klaus 17 April 2002 (has links)
The transport or the separation of solid particles or droplets suspended in a fluid flow is a common task in mechanical and process engineering. To improve machinery and physical processes (e.g. for coal combustion, reduction of NO_x and soot) an optimization of complex phenomena by simulation applying the fundamental conservation equations is required. Fluid-particle flows are characterized by the ratio of density of the two phases gamma=rho_P/rho_F, by the Stokes number St=tau_P/tau_F and by the loading in terms of void and mass fraction.
Those numbers (Stokes number, gamma) define the flow regime and which relevant forces are acting on the particle. Dependent on the geometrical configuration the particle-wall interaction might have a heavy impact on the mean flow structure. The occurrence of particle-particle collisions becomes also more and more important with the increase of the local void fraction of the particulate phase. With increase of the particle loading the interaction with the fluid phase can not been neglected and 2-way or even 4-way coupling between the continous and disperse phases has to be taken into account.
For dilute to moderate dense particle flows the Euler-Lagrange method is capable to resolve the main flow mechanism. An accurate computation needs unfortunately a high number of numerical particles (1,...,10^7) to get the reliable statistics for the underlying modelling correlations. Due to the fact that a Lagrangian algorithm cannot be vectorized for complex meshes the only way to finish those simulations in a reasonable time is the parallization applying the message passing paradigma.
Frank et al. describes the basic ideas for a parallel Eulererian-Lagrangian solver, which uses multigrid for acceleration of the flow equations. The performance figures are quite good, though only steady problems are tackled. The presented paper is aimed to the numerical prediction of time-dependend fluid-particle flows using the simultanous particle tracking approach based on the Eulerian-Lagrangian and the particle-source-in-cell (PSI-Cell) approach. It is shown in the paper that for the unsteady flow prediction efficiency and load balancing of the parallel numerical simulation is an even more pronounced problem in comparison with the steady flow calculations, because the time steps for the time integration along one particle trajectory are very small per one time step of fluid flow integration and so the floating point workload on a single processor node is usualy rather low.
Much time is spent for communication and waiting time of the processors, because for cold flow particle convection not very extensive calculations are necessary. One remedy might be a highspeed switch like Myrinet or Dolphin PCI/SCI (500 MByte/s), which could balance the relative high floating point performance of INTEL PIII processors and the weak capacity of the Fast-Ethernet communication network (100 Mbit/s) of the Chemnitz Linux Cluster (CLIC) used for the presented calculations. Corresponding to the discussed examples calculation times and parallel performance will be presented. Another point is the communication of many small packages, which should be summed up to bigger messages, because each message requires a startup time independently of its size. Summarising the potential of such a parallel algorithm, it will be shown that a Beowulf-type cluster computer is a highly competitve alternative to the classical main frame computer for the investigated Eulerian-Lagrangian simultanous particle tracking approach.
|
Page generated in 0.074 seconds