Master of Science / Department of Electrical and Computer Engineering / William B. Kuhn / An important concern for high speed circuit designs is that of crosstalk and electromagnetic interference. In PCB board-level designs, crosstalk at microwave frequencies may result from imperfections in shielding of PCB interconnects or more generally transmission lines. Several studies have been done to characterize and improve the isolation between PCB transmission lines for both digital and RF circuits. For example, previous studies in the microwave region have examined the effect that line type, line length, and separation have on crosstalk and suggest that without full shielding, the upper limit of isolation is on the order of 60dB for traditional board-level lines [1]. In order to more fully characterize crosstalk and improve isolation above 60 dB, this thesis studies signal-to-ground-plane separation, considers advanced line types, and examines the effect of 3D shielding. Results are presented from 100MHz to 30GHz for the traditional transmission line structures of microstrip, CPW, differential pair and CPW differential pair. This study shows that with a halving of distance between signal and ground planes, isolation between transmission lines can be reduced by as much as 20dB, making this one of the best ways to improve performance. Advanced methods of shielding are then presented. Direct launch stripline and single-sided CPW improve upon existing crosstalk reduction techniques, while split shielding and ablation of dielectric PCB material are also proposed. The data and additional crosstalk reduction techniques discussed in this thesis serve two purposes. One: with a more complete understanding of the effects that transmission line types and parameters have on crosstalk, engineers can quickly identify potential crosstalk issues and resolve them before manufacturing. Second, this thesis presents the engineer with four new additional techniques that may become available in advanced manufacturing environments. Such techniques can further reduce crosstalk and may allow for isolation values to approach 100 dB at the PC board level.

This diploma thesis focuses on G.fast and VDSL2 technologies and their comparison. G.fast has the prerequisites for replacing VDSL2 for short distances. This work describes in detail the modulation techniques of both DSL technologies - DMT modulation used by both technologies. The aim of this work is to create a software for comparing the transfer rates of all profiles of both technologies, including the effects of far-end crosstalk. This is performed in the Matlab environment. This work describes how the program works and how to run the simulations. The results of selected simulations and their charts are enclosed in this work.

Thesis deals with the analysis of the sliding contact in the ring mill. It focuses on the assessment of the effect of the current load on the sliding contact, the assessment of the signal transmission quality from the static to the rotara part of the ring contact slide contact.

The master thesis deals with G.fast and G.mgfast transmission technologies, including their parameters. The work deals with the principle of vector DMT modulation and the possibility of time duplex TDD and full-duplex FDX in two-way communication used in these technologies. The following is a description of the line using the KHM model, which is suitable for simulations in the transmission band using G.fast and G.mgfast technologies. Subsequently, the disturbing effects of crosstalk at the near end of NEXT and the far end of FEXT and their elimination with these technologies are discussing. Part of the work explains supporting calculations to determine the SNR and bit allocation to calculate the baud rate. The work describes the methods of compensation of crosstalk FEXT and NEXT, which affect the resulting baud rate. The work also includes an application for simulation of transmission speed as a function of distance for G.fast and G.mgfast technologies, allowing changing input parameters and adjusting the transmission bandwidth based on G.9700 and G.9701 standards. Also, in work, an application is created to display the compensation of the influence of the transmitted signal crosstalk FEXT and NEXT, which allow the import of measured crosstalk between individual participants. The issue of influencing crosstalk for accurate measurements in the laboratory is also discussing. An application in the MATLAB environment is creating to display the measured characteristics.

This work is focused on the subject of the interference modelling for xDSL technologies. First, the xDSL technologies are explained. Following is the presentation and description of the different kinds of the xDSL technologies. The next part deals with the basic parameters of metallic cable lines – especially the primary and secondary parameters. Nowadays wider bandwidths are used for the achievement of higher data transmission rates. During a higher frequency signal transmission a more intensive line attenuation appears. To identify the transfer characteristics of the lines while using an xDSL system, mathematic models of transmission lines are applied. That is why these mathematic models are dealt with in the next chapter. At the end of this section the mathematic models are compared using the modular and phase characteristics. The main aim of the work is to describe the different impacts which influence the efficiency of the xDSL systems. First, the causes interfering from the inside of the cable are deeply explained: Near End Crosstalk (NEXT), Far End Crosstalk (FEXT), Additive White Gaussian Noise (AWGN). Following is the explanation of the external interfering impacts: Radio Frequency Interference (RFI) and Impulse Noise. The next goal of this thesis is a design of a workstation for the tests of spectral features and the efficiency of the xDSL systems. The work also presents a designed GUI application and its description. The GUI application is an instrument for the choice or data entry of the final interference. The last chapter describes a realization of a measurement and shows the measured characteristics which were recorded on the ADSL tester and oscilloscope.

The thesis concerns the problem of interference modelling for xDSL technologies and Ethernet. The introduction describes the origin of crosstalk, that arise during the operation of the systems and the physical properties of the lines, therefore, the next section describes the properties of the primary and secondary parameters of the homogenous line and their modelling. In order to achieve higher data rates on the metallic line, systems with larger frequency spectrum are applied, resulting in a greater attenuation of the line. This issue and the characteristics determination of the transmission systems are subjects of the mathematical models, which are divided according to the modelling of primary or secondary parameters. The main goal of this work is to describe the effects which influence the performance of data transfer via xDSL and Ethernet technology focusing on internal and external disturbances acting on the cable lines. This is the crosstalk at the near and far end, adaptive white noise, radio frequency interference RFI and impulse noise. Following part of the thesis deals with the properties of xDSL technologies, specifically ADSL2+ and VDSL2 and Ethernet. Another aim is to design applications which enable to test the performance of xDSL and Ethernet transmission systems with its own award simulations interference. The conclusion describes the design and implementation of laboratory experiments for measuring of the efficiency and spectral properties of xDSL. The proposed laboratory protocols are annexed to this thesis, including the measured waveforms.

The master's thesis deals with one of the specifics of the cultural history of the Czech lands in the Early Modern period - i. e. the general perception of the afterlife (approximately between 1500 and 1800) and revenant issues. A revenant is meant originally a human being, who, after his death, for various reasons returns to the light of the living world, with exhibits of material (revived corpses, zombies, vampires, fexts) and immaterial (spirits, white ladies, wild hunting). In this respect, the main source are Czech demonological legends. One part of the study is to evaluate the social, religious and cultural aspects that had effect on what was said above in the specific historical period. The main emphasis is placed on the individual cases of revenants in the Czech lands, preserved in historical sources, as well as comparison with the same case in other European countries. The study will also focus on the description of biographies of historical personalities, drawing conclusions about what may have caused the conviction of being revenant.