Ces travaux de thèse portent principalement sur la génération de signal d'horloge haute fréquence. Dans un premier temps, la faisabilité d'un oscillateur à base de BAW y est démontrée par la conception d'un circuit en technologie CMOS 65 nm. Les deux principales innovations sont les performances en terme de stabilité (bruit de phase de -128dBc/Hz à 100kHz de la porteuse) et en précision (implémentation d'une banque de capacités ayant un pas de 0.4ppm) de l'oscillateur. Sa consommation est optimisée (0.9mW). Il est suivi d'un diviseur faible bruit (-140dBc/Hz à 100kHz de la porteuse) délivrant un signal à 500MHz. Dans un second temps, les imperfections des résonateurs BAW sont analysées. Une procédure de calibration comprenant une calibration initiale et une calibration en boucle ouverte est alors proposée. Cette dernière repose sur l'identification et l'utilisation d'un modèle comportemental du dispositif, régulièrement mis à jour grâce à un filtre de Kalman. Une précision de 0.4 ppm est atteinte / This thesis deals with the gigahertz range reference frequency generation. In a first part, this document presents the design of a 500 MHz oscillator in a 65 nm CMOS process using a 2 GHz Bulk Acoustic Wave resonator. A digital frequency control is implemented using a switched capacitor bank in parallel to the resonator. The tuning range is up to 500 kHz with a minimum step of 200 Hz. The oscillator core uses a differential topology and is designed for low phase noise (-128 dBc/Hz at 100 kHz offset) at low power consumption (0.9 mW). It is followed by a low noise divider which provides a 500 MHz output with a phase noise of -139 dBc/Hz at 100 kHz offset from the carrier. In a second part, we consider a method for the calibration of a BAW based frequency reference. In fact, the frequency variations of a BAW oscillator against process, supply, temperature and aging effects make difficult its use as a frequency reference. We propose here a method based on Kalman filtering to identify with high precision a behavioral model of this BAW reference, thus enabling its use in an open loop frequency tuning. A precision of 0.4 ppm is achieved

No description available.

No description available.

Call number: LD2668 .T4 1958 R47

ITC/USA 2007 Conference Proceedings / The Forty-Third Annual International Telemetering Conference and Technical Exhibition / October 22-25, 2007 / Riviera Hotel & Convention Center, Las Vegas, Nevada / This paper introduced a fast scanning and waiting acquisition method for a DS/FH receiver used in the telemetry field. Mathematic model of the hybrid DS/FH system’s acquisition process is given and discussed. The average acquisition time expression using this method and generalized average acquisition time formula is derived also. The validity of the proposed algorithm is verified after simulation. In the circumstances of Additive Gauss White Noise for the channel, simulation result at Ec/N0= -15dB shows that the average acquisition time is decreased almost 4 times than that of waiting and searching method.

Reliable timing and frequency synchronization is a major requirement in orthogonal frequency division multiple-access (OFDMA) systems as synchronization errors can result in inter-symbol-interference (ISI) and inter-carrier-interference (ICI) in the received signal, which severely degrade system performance. Thus, the objective of the proposed research is to develop, analyze, and prototype timing and frequency synchronization techniques for downlink (DL) and uplink (UL) OFDMA transmissions. For synchronization in DL OFDMA transmissions, we have developed conditions to select appropriate Zadoff-Chu sequences as training symbols that allow timing synchronization in the presence of large carrier frequency offsets (CFO). Using the proposed training block, we have designed training signal detection, timing synchronization, and integer CFO estimation algorithms. We have further proposed the training signal design for frequency synchronization in DL coordinated multi-point (COMP) transmissions, in which a user has to synchronize to multiple base-stations at the same time. In this respect, a frequency synchronization algorithm for DL COMP receiver has been designed using the proposed training signal along with its hardware implementation to analyze real-time performance. For frequency synchronization in UL OFDMA transmissions, we have proposed a null sub-carrier-based CFO estimation algorithm, and carried out its identifiability and acquisition range analysis. The proposed algorithm supports both sub-band and generalized sub-carrier allocations. We have also designed a CFO estimation and compensation algorithm for UL single-carrier frequency division multiple-access (SC-FDMA) transmissions. The proposed algorithm is based on parallel factor analysis and supports interleaved sub-carrier allocation. In addition, it guarantees the identifiability of CFO estimation and allows the system to operate on full load. Detailed simulations results have been provided along with discussions on computational requirements, which reveal that the proposed algorithms provide significant improvements in performance and efficiency compared to state of the art schemes in the literature.

International Telemetering Conference Proceedings / October 27-30, 1997 / Riviera Hotel and Convention Center, Las Vegas, Nevada / This paper describes the two main causes of fading encountered at test ranges. The first cause of fading results from nulls in the transmit antenna gain pattern. Variations in the received signal level are a result of changes in the gain pattern as the spatial relationship between transmitter and receiver change. The second cause of fading is due to multipath interference. This occurs when multiple copies of the transmitted signal with different delays arrive at the receiver and are phased relative to each other so that destructive interference occurs.

Today’s thin-film passive components such as capacitors and inductors are limited to low volumetric density and large form-factors that pose as major roadblock to miniaturization of the power modules. These components are also placed far away from the IC’s leading to large interconnect parasitics and lower operating frequencies. Novel thin-film technologies with high densities and small form-factors are, therefore, required to enable miniaturization and performance at high frequencies. Glass- and silicon- based interposer technologies that utilize vertical through-via interconnections have shown way to improve power distribution network (PDN) performance with thin power-ground planes. However, integration of ultra-high density capacitors in such substrates has not yet been demonstrated. This thesis addresses these challenges with tantalum-based, silicon-integrated, ultrathin, high-density capacitors at higher operating frequencies with lower leakage properties (<0.01µA/µF). The anodization kinetics of tantalum pentoxide and the underlying leakage current mechanisms are investigated to provide optimal process guidelines. The thin-film Ta capacitors demonstrated capacitance density of 0.1 µF/mm2 at 1-10 MHz in form-factors of 50 µm, which corresponds to 6X higher volumetric density relative to commercial tantalum capacitors. An innovative approach to address incompatibility of tantalum electrodes with substrates is pursued by prefabricating the electrodes on a free-standing foil, which are then transferred onto the active wafer to form the capacitors on Si. The integration approach is designed to embed these thin tantalum capacitors on alternative substrates such as organic, glass or silicon, with copper via interconnections for lower parasitics. The thesis also explores titanium-based high-density capacitors with high-permittivity titania dielectric as a potential alternate high-density capacitor technology.

This thesis reports the methods, the deployment strategies and the resulting system performance improvement of in-building environmental modification. With the increasing use of mobile computing devices such as PDAs, laptops, and the expansion of wireless local area networks (WLANs), there is growing interest in increasing productivity and efficiency through enhancing received signal power. This thesis proposes the deployment of waveguides consisting of frequency selective surfaces (FSSs) in indoor wireless environments and investigates their effect on radio wave propagation. The received power of the obstructed (OBS) path is attenuated significantly as compared with that of the line of sight (LOS) path, thereby requiring an additional link budget margin as well as increased battery power drain. In this thesis, the use of an innovative model is also presented to selectively enhance radio propagation in indoor areas under OBS conditions by reflecting the channel radio signals into areas of interest in order to avoid significant propagation loss. An FSS is a surface which exhibits reflection and/or transmission properties as a function of frequency. An FSS with a pass band frequency response was applied to an ordinary or modified wall as a wallpaper to transform the wall into a frequency selective (FS) wall (FS-WALL) or frequency selective modified wall (FS-MWALL). Measurements have shown that the innovative model prototype can enhance 2.4GHz (IEEE 802.11b/g/n) transmissions in addition to the unmodified wall, whereas other radio services, such as cellular telephony at 1.8GHz, have other routes to penetrate or escape. The FSS performance has been examined intensely by both equivalent circuit modelling, simulation, and practical measurements. Factors that influence FSS performance such as the FSS element dimensions, element conductivities, dielectric substrates adjacent to the FSS, and signal incident angles, were investigated. By keeping the elements small and densely packed, a largely angle-insensitive FSS was developed as a promising prototype for FSS wallpaper. Accordingly, the resultant can be modelled by cascading the effects of the FSS wallpaper and the ordinary wall (FSWALL) or modified wall (FS-MWALL). Good agreement between the modelled, simulated, and the measured results was observed. Finally, a small-scale indoor environment has been constructed and measured in a half-wave chamber and free space measurements in order to practically verify this approach and through the usage of the deterministic ray tracing technique. An initial investigation showing that the use of an innovative model can increase capacity in MIMO systems. This can be explained by the presence of strong multipath components which give rise to a low correlated Rayleigh Channel. This research work has linked the fields of antenna design, communication systems, and building architecture.

The dynamics of spin and mechanical displacement in ionic materials are independently well understood. This abstract work aims to investigate the spin and the displacement dynamics of two ions, while including coupled interactions between the ions’ spin and displacement. I have found that the dynamics depend on the speed of both the spin and the displacement. / Joners spinn- respektive förflyttningsdynamik har väl etablerade teoretiska grunder. Med syftet att utöka den teoretiska kunskapen undersöker jag hur spinn- och förflyttningsdynamiken hos två joner påverkas av kopplade interaktioner mellan deras spinn och förflyttning. Resultatet visar att dynamiken beror på spinnets och förflyttningens farter.