Spelling suggestions: "subject:"fenton method"" "subject:"denton method""
1 |
Study on the Treatment of Electroplating Wastewater by Ferrite Process Combined with Fenton¡¦s MethodHu, Wei-hsien 30 June 2008 (has links)
The electroplating wastewater is usually treated by chemical precipitation, and the generated sludge has loose structure to cause the difficulties in sedimentation and filtration. Moreover, the sludge is unstable and the contained heavy metals are easily leached. Solidification is one method to deal with this kind of sludge; however it cause another problem, land requirement.
In this study, the contents of electroplating wastewater are divided into two parts organic matters and heavy metals; organic matters are treated by Fenton method and heavy metals are by Ferrite process. The purpose of this study is that through the serial Fenton-Ferrite Process treatment the effluent water and the sludge generated from the procedure could meet the standards in Taiwan.
It was well-know that the primary operation factors of Ferrite Process are pH, reaction temperature, ferrous ion concentration, time and aeration. The results showed that the proper factors of FP were pH=10, temperature= 90¢J, Fe/M molar ratio= 7,reaction time=80 min and aeration rate=1.0 L air / min / L solution. However, in Fenton method, the parameters of pH, hydrogen peroxide, ferrous ion concentration, and reaction time were discussed. I had greatest efficiency under the data showed that Fenton method pH = 3, ferrous ion concentration=3000 mg/L, hydrogen peroxide = 13000 mg/L, and reaction time=2 hr.
The wastewater measured COD =1162 mg/L, Cr=70 mg/L, Zn=400 mg/L. The treatment efficiency of the procedure combining Fenton method and Ferrite Process were that COD=88.5 mg/L, Cr=1.06 mg/L, and Zn=0.98 mg/Lin effluent water and the TCLP test results of sludge were Cr=3.37 mg/L, Zn=2.46 mg/L. All the data showed that the combination of the two process can significantly treat wastewater to meet the standards. Furthermore, the sludge can be recycled as magnetic materials or other purposes due to it¡¦s specific properties.
|
2 |
The Application of Ferrite Process on Industrial Wastewater Treatment and the Catalysis of FerrospinelsHuang, Yu-jen 17 July 2009 (has links)
In industrial wastewater, there are usually many kinds of organics and heavy metals and can cause damage on human health and environment without well treatment. Printed Circuit Board (PCB) industrial wastewater is a typical example due to the complicated manufacture processes and the use of specific chemicals. In this study, the PCB industrial wastewater is collected and then treated by the combination of Fenton method and Ferrite Process (or called Fenton-Ferrite Process, FFP). Moreover, the recycling possibility of sludge generated from FFP is also studied. Through this study, the treatment procedure of wastewater containing organics heavy metals is established and the direction of sludge reuse is also provided.
To realize the characteristic of PCB industrial wastewater, the wastewater from some PCB factory in southern Taiwan was firstly collected and analyzed to identify the pollution concentrations and then treated by FFP. The experimental results showed that the optimum parameters of Fenton method in FFP were pH = 2, [Fe2+]= 500 mg/L, [H2O2]= 3000 mg/L, reaction time= 60 min and batch dosing, and the residual COD and TOC were 84.9 mg/L and 58.3 mg/L under the COD regulation standard 120 mg/L. Meanwhile, the proper conditions of Ferrite Process in FFP were pH= 10, reaction temperature= 80¢J, reaction time= 40 min, aeration rate= 3 L/min/L wastewater, Fe/Cu molar ratio= 10 and three-stage reaction. Under that circumstance, the residual [Cu2+] in wastewater was 0.18 mg/L and the Toxicity Characteristic Leaching Procedure (TCLP) test of sludge from FFP was 4.58 far below the effluent standard 3 mg/L and TCLP standard 15 mg/L.
The properties of sludge were further investigated by X-Ray Diffractometer (XRD), Scanning Electron Microscope (SEM) and Superconducting Quantum Interference Device (SQUID). The pattern of XRD indicated that the major structures were Fe3O4 and CuFe2O4; the figure of SEM showed that the surface of sludge was composed of many round particles and the distribution of particle size was from 50 nm-100 nm; the magnetic property analyzed by SQUID showed that the saturation moment was 62.85 emu/g.
In the research of sludge applied in catalytic incineration, the o-xylene conversion was 97 % by sludge but only 31 % by quartz sand at 400 ¢J. Moreover, in the 72 hr-decay test of catalyst, the results clearly indicated that the performance did not obviously decline and there were no any byproducts but CO2. Therefore, the investigation revealed that the sludge had great potential in catalytic reaction.
The catalytic performance of various ferrospinels generated from different manufactured conditions was also studied. Through the screening of catalysts, the order of various ferrospinels activity was Cu-ferrite > Mn-ferrite > ferrite ¡Ü Zn-ferrite and the most effective Cu-ferrite was manufactured at pH= 9 and T= 90 ¢J. After 72 hr test, the decay of catalyst was not also found. In the examination of Cu-ferrite physical property, the XRD pattern showed that the structure was CuFe2O4; the figure of SEM illustrated that there was no difference between the surface of fresh and used catalyst; the magnetic property measured by SQUID showed that the saturation moment was 30.89 emu/g.
|
3 |
Padan 95 SP treatment by electrochemical process and its combination with other techniquesNguyen Tien, Hoang 06 November 2019 (has links)
This dissertation describes electrochemical oxidation of Padan 95 SP on Boron-doped diamond (BDD) electrode mainly by •OH radicals (which was measured by indirect method, i.e: the formation of 2-Hydroxylterephthalic acid (2-HTA)), Electro-Fenton and the combination with adsorption technology for increasing total organic carbon (TOC) removal efficiency. In this study, the formation of 2-HTA on BDD electrode via the reaction between terephthalic acid (TA) and •OH as a method to quantify hydroxyl radical formation was investigated. The degradation of Cartap in Padan 95SP (95 % Cartap) on BDD was investigated. Operating parameters such as applied current density, types of electrolyte and initial concentration of Padan 95SP were varied in order to determine their effect on the degradation efficiency of Cartap. The concentration of Cartap was determined by UV-Vis spectroscopy according to 5,5-Dithiobis-(2-nitrobenzoic acid) (DTNB) procedure. High Performance Liquid Chromatography (HPLC) and Gas Chromatography/Mass Spectrometry (GC-MS) were used to characterize the commercial Padan 95SP and the formation of by-products. The optimal conditions for Cartap degradation by electrochemical process have been established: concentration of electrolyte: 0.05 M Na2SO4, initial concentration of Padan 95SP: 300 mg·L-1, pH = 3, current density: j = 20 mA·cm-2. At this condition, Cartap decreases to 41 %, TOC decay reaches 8 %. To increase TOC decay at higher Padan 95 SP concentration in aqueous solution, the combination technique of electrochemical process with other techniques was proposed, e.g.: Electro-Fenton technique, pre-oxidizing by NaOCl or the Electro-Adsorption combination.
In the Electro-Fenton technique, we investigated the influence of factors such as the presence of NaOCl in pretreatment of process, affects of H2O2 concentration, Fe2+ dosage, co-catalysts metals ion and pH. The efficiency shows approximately 80 % of TOC removed at 700 mg·L-1 Padan 95 SP.
The combination of electrochemical with adsorption method shows the efficient removals of TOC and Padan 95SP (95 % Cartap) based on reagents oxidation in electrochemical process and adsorption of granular activated carbon (GAC), respectively. The influence of factors such as supporting electrolytes, flow rate, bed height, recycling number as well as initial concentration were investigated in order to determine their effects on TOC removal. The efficiency of this combination shows approximately 75 % of TOC and more than 90 % of Cartap removed at 700 mg·L-1 Padan 95 SP. Fourier Transform Infrared (FT-IR) and (Brunauer–Emmett–Teller) BET surface analysis were applied to investigate GAC before and after usage. The results have shown that the application of electrochemical technique with other methods can be the potential option for treatment of wastewater containing Padan 95 SP. / Diese Dissertation befasst sich mit der Reduktion des gesamten organischen Kohlenstoffs (TOC) aus wässriger Lösung, die Padan 95 SP enthält. Als Methoden zur Minimierung von TOC wurden die elektrochemische Oxidation von Padan 95 SP auf Bor-dotierter Diamant (BDD) Elektroden durch •OH Radikale, Elektro-Fenton und die Kombination mit Adsorptionstechnologien verwendet. Die •OH Radikale wurden dabei durch indirekte Methoden, z. B. die Bildung von 2-HTA gemessen. Zur Quantifizierung der Hydroxylradikalbildung wurde in dieser Studie die Bildung von 2-Hydroxylterephthalsäure (2-HTA) an BDD-Elektroden über die Reaktion zwischen Terephthalsäure (TA) und •OH untersucht. Weiterhin befasst sich die Arbeit mit dem Abbau von Cartap in Padan 95SP (95% Cartap) auf BDD über die Reaktion zwischen Cartap und Hydroxylradikalen. Betriebsparameter wie die angewandte Stromdichte, die Elektrolytarten und die Anfangskonzentration von Padan 95SP wurden variiert, um ihre Wirkung auf die Abbaueffizienz von Cartap zu bestimmen. Die Konzentration von Cartap wurde mittels UV-Vis-Spektroskopie mit dem 5,5-Dithiobis-(2-Nitrobenzoesäure) (DTNB) Verfahren bestimmt. Hochleistungs-Flüssigkeitschromatographie (HPLC) und Gaschromatographie/Massenspektrometrie (GC-MS) wurden verwendet, um das kommerziell erhältliche Padan 95SP und die Bildung von Nebenprodukten beim Abbau von Cartap zu charakterisieren. Die optimalen Bedingungen für die Cartap-Degradation durch den elektrochemischen Prozess wurden festgelegt: Konzentration des Elektrolyten: 0.05 M Na2SO4, Padan 95SP Anfangskonzentration: 300 mg·L-1, pH = 3, Stromdichte: j = 20 mA·cm-2. Unter diesen Bedingungen sinkt Cartap auf 41% und der TOC erreicht 8 % des jeweiligen Ausgangswertes. Um den TOC-Zerfall bei höher Padan 95 SP Konzentration in Wasser zu erhöhen, wurde die Kombination des elektrochemischen Prozesses mit anderen Techniken vorgeschlagen, z.B.: Elektro-Fenton-Technik, Oxidation mit NaOCl, oder die Kombination des elektrochemischen Prozesses mit einem Adsorptionsprozess.
Bei der Elektro-Fenton-Technik wurde der Einfluss von Faktoren wieder Anwesenheit von NaOCl in der Prozessvorbehandlung, Auswirkungen der H2O2-Konzentration, Fe2+-Dosierung, Metallionen als Cokatalysatoren und der pH-Wert der Lösung untersucht, um die Wirkung auf die Abbau-Effizienz für Cartap zu bestimmen. Es konnten mit dieser Methode rund 80 % TOC, ausgehend von 700 mg·L-1Padan 95SP, entfernt werden.
Die Kombination des elektrochemischen Prozesses mit einer Adsorptionsmethode ermöglicht eine effiziente Entfernung von TOC und Padan 95SP (95% Cartap). Dies basiert auf der Oxidation und anschließender Adsorption auf granularer Aktivkohle (GAC). Der Einfluss von Faktoren wie Leitelektrolyten, Flussrate, Betthöhe, Recyclingzahl sowie die Anfangskonzentration von Padan 95 SP wurde untersucht, um deren Auswirkungen auf die TOC Entfernung zu bestimmen. Durch die Kombination konnten so 75% desTOC und mehr als 90% Cartap bei 700 mg·L-1Padan 95 SP entfernt werden. Fourier-Transformations-Infrarot (FT-IR) und BET-Oberflächenanalyse wurden angewendet, um GAC vor und nach der Verwendung zu untersuchen. Die Ergebnisse haben gezeigt, dass die Kombination des elektrochemischen Prozesses mit anderen Methoden eine potentielle Option für die Behandlung von Abwasser, das Padan 95 SP enthält, sein kann.
|
Page generated in 0.0386 seconds