Spelling suggestions: "subject:"bainite Element analyses"" "subject:"bainite Element enalyses""
1 |
On the geometrically nonlinear constant moment triangle (with a note on drilling rotations)Providas, Efthimios January 1990 (has links)
No description available.
|
2 |
Simulation of the deformation of a stope support design / Abraham Johannes LaubscherLaubscher, Abraham Johannes January 2014 (has links)
Supported stope mining is one of the most common types of mining in the modern day gold
mining industry. The excavated regions, where ore is extracted, are supported with a
combination of roof-bolting, timber packs, backfill, timber props and mechanical prop
technologies. In order to install a support system that will be able to absorb the energy
released by the elastic movement of the surrounding rock mass and support the unstable
hanging wall, it is necessary for the rock engineer to know how the individual types of
support will react to different load conditions in order to design a safe support system.
Current support systems are developed using knowledge from past experience and trial and
error processes. These are expensive and time consuming methods that can possibly be
improved and made more cost effective by using modern design techniques.
A study was conducted to determine the feasibility of the application of Finite Element
Modelling (FEM) to the deformation of a modern support unit under specified quasi-static
and dynamic stope load conditions with the view to assist in the prediction of the
operational performance of support units that cannot be experimentally tested due to a lack
of test equipment, capabilities and facilities. The study was extended by investigating the
theoretical possibility of buckling due to an impact load on the prop and the performance of
the prop. To achieve this, a simulation was carried out using ANSYS™ transient structural
software to determine whether it is possible to simulate the performance curve of a prop.
Computerised methods were used to determine the possibility of failure due to buckling and
the implications of buckling, if it occurs, on the performance of a specific support prop
design.
In summary this study proved that it is possible to simulate the performance curve of a
friction prop design in order to compare the result obtained with the required performance,
provided that the correct friction coefficients between prop mating surfaces are known. It
also presents a methodology to investigate the theoretical effect of high velocity impact
load on the buckling potential of a friction prop design and slender columns in general,
which is highly applicable to these types of support.
The methodologies used in this study can be applied to different designs of friction props,
and possibly reduce the development costs and implementation time of these types of
support units. / MIng (Mechanical Engineering), North-West University, Potchefstroom Campus, 2014
|
3 |
Simulation of the deformation of a stope support design / Abraham Johannes LaubscherLaubscher, Abraham Johannes January 2014 (has links)
Supported stope mining is one of the most common types of mining in the modern day gold
mining industry. The excavated regions, where ore is extracted, are supported with a
combination of roof-bolting, timber packs, backfill, timber props and mechanical prop
technologies. In order to install a support system that will be able to absorb the energy
released by the elastic movement of the surrounding rock mass and support the unstable
hanging wall, it is necessary for the rock engineer to know how the individual types of
support will react to different load conditions in order to design a safe support system.
Current support systems are developed using knowledge from past experience and trial and
error processes. These are expensive and time consuming methods that can possibly be
improved and made more cost effective by using modern design techniques.
A study was conducted to determine the feasibility of the application of Finite Element
Modelling (FEM) to the deformation of a modern support unit under specified quasi-static
and dynamic stope load conditions with the view to assist in the prediction of the
operational performance of support units that cannot be experimentally tested due to a lack
of test equipment, capabilities and facilities. The study was extended by investigating the
theoretical possibility of buckling due to an impact load on the prop and the performance of
the prop. To achieve this, a simulation was carried out using ANSYS™ transient structural
software to determine whether it is possible to simulate the performance curve of a prop.
Computerised methods were used to determine the possibility of failure due to buckling and
the implications of buckling, if it occurs, on the performance of a specific support prop
design.
In summary this study proved that it is possible to simulate the performance curve of a
friction prop design in order to compare the result obtained with the required performance,
provided that the correct friction coefficients between prop mating surfaces are known. It
also presents a methodology to investigate the theoretical effect of high velocity impact
load on the buckling potential of a friction prop design and slender columns in general,
which is highly applicable to these types of support.
The methodologies used in this study can be applied to different designs of friction props,
and possibly reduce the development costs and implementation time of these types of
support units. / MIng (Mechanical Engineering), North-West University, Potchefstroom Campus, 2014
|
4 |
Evaluation of time varying stresses in a Howden fanvan Mierlo, Tim, Żywalewski, Rafal January 2015 (has links)
In this work, the time varying stresses in a Howden axial flow fan are obtained by finite element analyses. Dynamic substructuring is used to obtain accurate values of the stresses in the threads of the blade shaft, the component which connects the blade with the hub. Three different global models are used to compare the influence of neglecting the fan shaft and the stiffness influence of the centrifugal force. The relative displacements, which are obtained from the global models, have been used as boundary condition in the detailed models. The detailed models are used to obtain the Von Mises stresses in the root of the threads of the blade shaft. Finally the results of the three global models are compared with experimental measured data provided by Howden. The experimental data results in the highest Von Mises stresses. The model with the fan shaft and the stiffness influence of the centrifugal force gives values for the Von Mises stresses which are approximately twenty percent lower. The model without the fan shaft results in the lowest stresses which are approximately forty percent lower than the stresses obtained using the measured data.
|
5 |
Estudo comparativo de diferentes mini-implantes utilizados para mesialização de segundo molar inferior: análise por elementos finitos 3d / Study of different mini-implants used for lower molar mesialização: Analysis by finite elements 3dLisboa, Juliana da Costa 13 July 2018 (has links)
Submitted by Juliana da Costa Lisbôa (julianalisboa86@hotmail.com) on 2018-09-10T11:26:11Z
No. of bitstreams: 1
Juliana C Lisboa.pdf: 1704367 bytes, checksum: 0a852a606d663babe8ff1cd313f64b57 (MD5) / Approved for entry into archive by Silvana Alvarez null (silvana@ict.unesp.br) on 2018-09-10T19:21:58Z (GMT) No. of bitstreams: 1
lisboa_jc_me_sjc.pdf: 1704367 bytes, checksum: 0a852a606d663babe8ff1cd313f64b57 (MD5) / Made available in DSpace on 2018-09-10T19:21:59Z (GMT). No. of bitstreams: 1
lisboa_jc_me_sjc.pdf: 1704367 bytes, checksum: 0a852a606d663babe8ff1cd313f64b57 (MD5)
Previous issue date: 2018-07-13 / A perda do primeiro molar é uma situação comum na rotina do consultório e com isso surgem alternativas de tratamento para reabilitação, sendo uma delas, o fechamento de espaço através da mesialização do segundo molar. O uso de mini- implante proporciona ancoragem máxima, costuma ser bem tolerado pelo paciente e se destaca pela facilidade de instalação e remoção, apresentando dessa maneira desempenho clínico bastante favorável. O objetivo desse estudo foi analisar a distribuição de tensões em modelo que simula a mesialização de molar inferior utilizando diferentes tipos de mini-implantes. Embasado no método dos elementos finitos foi obtido modelo ósseo de mandíbula por recomposição de uma tomografia computadorizada realizada pelo software Invesalius (CTI, São Paulo, Brasil). O desenho do segundo molar foi obtido por técnica de recomposição tomográfica. Elementos de ancoragem auto-perfurantes da marca Neodent e também auto-rosqueantes da marca Titanium Fix foram desenhados e modelados por ferramenta de revolução do perfil desenhado no software Rhinoceros 3D, inseridos ao bloco ósseo e então submetidos a cargas de 200 cN. Os resultados foram calculados e analisados pelo programa Ansys 17.0 para verificação por meio da análise de mapas de deslocamento e tensões máximas principais, principalmente do osso cortical e indicaram que, dentro do modelo experimental, o ligamento periodontal apresentou valores baixos de tensão máxima principal, porém dentro dos valores fisiológicos para prover a movimentação, com visualização de áreas de compressão e de tração com escala entre 0,1 a -0,1 MPa. Concluiu-se que a carga testada permite a deslocamento dentário porém com tendência a giroversão. / The loss of the first molar is a common situation in the routine of the dentist and with this treatment alternatives for rehabilitation arises, one of them being the closure of space through the mesialization of the second molar. The use of mini-implants provides maximum anchorage, is well tolerated by the patient and stands out for ease installation and removal, thus presenting a very favorable clinical performance. The objective of this study was to analyze the stress distribution in a model that simulates the inferior molar mesialization using different types of mini- implants. Based on the finite element method, a mandible bone model was obtained by recomposing a computerized tomography performed by invesalius software (CTI, São Paulo, Brazil). The second molar design was obtained by a technique similar to the tomographic recomposition. Neodent self-piercing anchoring elements and also Titanium Fix self-piercing anchors were designed and modeled by a revolution tool in the Rhinoceros 3D software, inserted into the bone block and then subjected to loads of up to 200 cN. The results were calculated and analyzed by the Ansys 17.0 program for verification by means of the analysis of displacement maps and main maximum stresses, mainly of the cortical bone and indicated that, within the experimental model, the periodontal ligament presented low values of main maximum tension, however within the physiological values to provide the movement, with visualization of areas of compression and traction with scale between 0.1 and -0.1 MPa. It was concluded that the load tested allows dental displacement but with a tendency to gyroversion.
|
6 |
The optimal placement of geogrid reinforcement in landfill clay linersMarx, David Hercules January 2017 (has links)
Continued population growth is placing strain on the waste disposal facilities available in South Africa. However, limited air space suitable for landfilling drives the need for alternative solutions such as piggyback landfills to expand the waste disposal capacity. This method entails building a new, fully lined, landfill on top of existing waste. However, the old underlying waste is prone settlement that can result in the cracking of new landfill clay liner.
Geogrid reinforcement have been successfully used in clay liners to mitigate cracking induced by waste settlement. This research focused on investigating of the optimal reinforcement strategy (ORS) of such a liner subject to settlement. The ORS entails the optimal position for geogrid reinforcement in a liner, and the stiffness to be used at that position, given a total reinforcement cost.
Firstly, the fracture behaviour of unreinforced clay liners was investigated by means of four point bending tests on clay beams. It was found that the fracture of this clay occurred in three stages: linear behaviour, followed by non-linear behaviour when micro-cracks forms and finally macro-cracks that opened once the peak load was reached.
Thereafter, the behaviour of geogrid-reinforced clay liners, subjected to differential settlement, was investigated with finite element analyses in ABAQUS. A number of key factors were varied and the resulting change in behaviour of the liners was observed. These were: the overburden stress applied, clay liner thickness, magnitude of central settlement and the width and shape of the settlement trough developing in the underlying waste body.
Based on the numerical results, a series of plane-strain centrifuge tests of reinforced clay liners subject to differential settlement were designed. An unreinforced liner, a liner reinforced at the bottom quarter, a liner reinforced at the top quarter and a liner reinforced at both the bottom and top quarters were tested. Laser scanner scans of the surface and strains calculated from digital image velocimetry results were used to compare the behaviour of the liners. Based on these results it is recommended that for optimal performance the available reinforcement should be divided between the top and bottom quarters of the liner to mitigate the effect of settlement. / Volgehoude bevolkingsgroei in Suid-Afrika plaas bestaande rommelstortingsfasiliteite onder druk. ’n
Tekort aan grond geskik vir die bou van stortingsterreine moedig die soektog na alternatiewe oplossings
soos abba-stortingsterreine aan. Hierdie metode behels ’n splinternuwe stortingsterrein wat bo-op
bestaande rommel gebou word. Versakking van die bestaande rommel kan egter veroorsaak dat krake
vorm in die nuwe stortingsterrein se kleivoering wat daarop lê.
Vorige navorsing het die vorming van krake in die kleivoerings al welgeslaagd verhoed deur van
georoosters as versterking gebruik te maak. Die huidige studie het op daardie navorsing gebou deur die
optimale versterkings strategie (OVS) te bepaal vir so ’n kleivoering wat vervorm onder versakking van
die onderliggende rommel. Die OVS definieer beide die optimale versterkings posisie in ’n kleivoering,
en die styfheid van die georooster wat in daardie posisie geplaas moet word, gegewe ’n sekere totale
versterkingskoste.
Eerstens was daar ondersoek ingestel na die kraakgedrag van onversterkte kleivoerings. Vierpuntbuigtoetse
van kleibalkies was hiervoor gebruik. Die krake het oor drie fases gevorm: eerstens was
daar lineêre gedrag tot en met mikro-krake gevorm het. Dit is gevolg deur nie-lineêre gedrag wat gelei het tot makro-krake. Sodra die makro-krake gevorm het, is die maksimum las bereik wat die klei kon
ondersteun.
Na afloop van die balkbuigtoetse was eindige element analises in ABAQUS uitgevoer om die gedrag
van versterkte kleivoerings wat bo-op versakkende afval lê te ondersoek. Die spanning toegepas op die
oppervlak van die kleivoerings, die dikte van die kleivoerings en die versakkingstrogwydte, -vorm en
-diepte was gevarieer om die effek daarvan op die gedrag van die kleivoerings te ondersoek.
Na aanleiding van die resultate van die numeriese analise is ’n reeks sentrifuge toetse van kleivoerings
wat aan versakking onderwerp word uitgevoer. ’n Onversterkte kleivoering, kleivoerings versterk in
die boonste en onderste kwarte, en een versterk in beide die boonste en onderste kwart was getoets.
Die gedrag van die verskillende kleivoerings was vergelyk deur die oppervlaktekrake op te meet met
’n laserskandeerder. Verder is die vervorming van die kleivoerings bepaal vanaf die verplasing van
die grondpartikels tussen opeenvolgende digitale foto’s. Na aanleiding van hierdie resultate word
dit aanbeveel dat die beskikbare georooster versterking opgedeel moet word tussen die boonste en
onderste kwart van die kleivoerings ten einde optimale gedrag te verseker indien versakking sou
plaasvind. / Dissertation (MEng)--University of Pretoria, 2017. / Deutscher Akademischer Austausch Dienst (DAAD) / Geosynthetics Interest Group of South Africa (GIGSA) / National Research Foundation of South Africa (NRF) / Civil Engineering / MEng / Unrestricted
|
7 |
Biomechanics of Spine Following the Long Segment Fusions and various Surgical Techniques to reduce the Occurrence of Proximal Junction Kyphosis (PJK)Shah, Anoli Alaybhai January 2021 (has links)
No description available.
|
8 |
Experimental and Analytical Investigations of Piles and Abutments of Integral BridgesArsoy, Sami 05 January 2001 (has links)
Bridges without expansion joints are called "integral bridges." Eliminating joints from bridges crates concerns for the piles and the abutments of integral bridges because the abutments and the piles are subjected to temperature-induced cyclic lateral loads. As temperatures change daily and seasonally, the lengths of integral bridges increase and decrease, pushing the abutment against the approach fill and pulling it away. As a result the bridge superstructure, the abutment, the approach fill, the foundation piles and the foundation soil are all subjected to cyclic loading, and understanding their interactions is important for effective design and satisfactory performance of integral bridges.
The ability of piles to accommodate lateral displacements is a significant factor in determining the maximum possible length of integral bridges. In order to build longer integral bridges, pile stresses should be kept low.
This research project investigated the complex interactions that take place between the structural components of the integral bridge and the soil through experimental and analytical studies. A literature review was conducted to gain insight into the integral bridge/soil interactions, and to synthesize the information available about the cyclic loading damage to piles of integral bridges. The ability of the piles and the abutments to withstand cyclic loads was investigated by conducting large-scale cyclic load tests. Three pile types and three semi-integral abutments were tested in the laboratory. Experiments simulated 75 years of bridge life for each specimen by applying over 27,000 displacement cycles. Numerical analyses were conducted to investigate the interactions among the abutment, the approach fill, the foundation soil, and the piles.
The original VDOT semi-integral abutment hinge experienced shear key failure as observed in two large-scale laboratory tests. The revised hinge detail did not exhibit any sign of damage. Both abutments tolerated 75-year worth of displacement cycles without any appreciable change in their behavior. Semi-integral abutments are recommended for longer integral bridges because they can reduce pile stresses. As the need to build longer integral bridges grows, the role of the semi-integral abutments is expected to become more important.
The data from the experimental program indicates that steel H-piles are the best pile type for support of integral abutment bridges. Concrete piles are not recommended because under repeated lateral loads, tension cracks progressively worsen and significantly reduce vertical load carrying capacity of these piles. Pipe piles have high flexural stiffness, which results in an undesired condition for the shear stresses in the abutment. For this reason, stiff pipe piles are not recommended for support of integral bridges.
Numerical analyses indicate that the interactions between the approach fill and the foundation soils create favorable conditions for stresses in piles supporting integral bridges. Because of these interactions, the foundation soil acts as if it were softer, resulting in reduction in pile stresses compared to a single pile in the same soil without the approach fill above it. / Ph. D.
|
9 |
The effect of prism orientation and loading direction on contact stresses in prismatic enamel: implications for interpreting wear patternsMacho, Gabriele A., Shimizu, D., Spears, I.R. January 2005 (has links)
No / The ability of prisms to effectively dissipate contact stress at the surface will influence wear rates in teeth. The aim of this investigation was to begin to quantify the effect of prism orientation on surface stresses. Seven finite element models of enamel microstructure were created, each model differing in the angulation of prism orientation with regard to the wear surface. For validation purposes, the mechanical behavior of the model was compared with published experimental data. In order to test the enamel under lateral loads, a compressed food particle was dragged across the surface from the dentino-enamel junction (DEJ) towards the outer enamel surface (OES). Under these conditions, tensile stresses in the enamel model increased with increases in the coefficient of friction. More importantly, stresses were found to be lowest in models in which the prisms approach the surface at lower angles (i.e., more obliquely cut prisms), and highest when the prisms approached the surface at 60° (i.e., less obliquely cut). Finally, the direction of travel of the simulated food particle was reversed, allowing comparison of the difference in behavior between trailing and leading edge enamels (i.e., when the food particle was dragged either towards or away from the DEJ). Stresses at the trailing edge were usually lower than stresses at the leading edge. Taken together with what is known about prism orientation in primate teeth, such findings imply greater wear resistance at the intercuspal region and less wear resistance at the lateral enamel at midcrown. Such findings appear to be supported by archeological evidence.
|
10 |
Behaviour and Design of Profiled Steel Cladding Systems Subject to Pull-through FailuresMahaarachchi, Dhammika January 2003 (has links)
The common profiled steel cladding systems used in Australia and its neighboring countries are made of very thin (0.42 mm) high strength steel (G550 with a minimum yield stress of 550 MPa) and are crest-fixed. However, these claddings often suffer from local pull-through failures at their screw connections during high wind events such as storms and cyclones. Past experience and researches have shown that the loss of steel roofs has often occurred due to local pull-through failures of their screw connections under uplift or suction loading. Loss of claddings always led to a progressive collapse of the entire building. This situation is continuing because of the lower priority given to the design of roof and wall cladding systems. At present, steel design codes do not provide guidelines for the design of crest-fixed steel roof or wall claddings. Past research has shown that European and American recommendations for steel claddings cannot be used for Australian crest-fixed cladding systems as they were developed mainly for valley-fixed claddings subjected to gravity loading instead of crest-fixed claddings subjected to wind uplift/suction loading. Therefore at present the design of thin steel cladding systems is based on laboratory tests and is expensive. These situations inhibit the innovative design and advances in the steel cladding industry. Since the local pull-through failures in the less ductile G550 steel claddings are initiated by transverse splitting at the fastener hole, analytical studies have not been able to determine the pull-through failure loads accurately. Therefore in the first stage of this research an appropriate fracture/splitting criterion was developed using a series of large scale and small scale experiments of crest-fixed steel claddings. A shell finite element model of crest-fixed steel cladding was then developed that included the new fracture/splitting criterion and advanced features such as hyperelastic material modelling, contact simulations, residual stresses and geometric imperfections. The improved finite element analyses were able to model the pull-through failures associated with splitting as evident from the comparison of their results with the corresponding full-scale experimental results. An extensive series of parametric studies considering the effects of material properties and geometric parameters of the two commonly used trapezoidal cladding profiles was undertaken using finite element analysis. Appropriate design formulae for the pull-through and dimpling failure load of trapezoidal profiles were then derived for optimization purposes and to simplify the current design method. This will then lead to modification and optimisation of cladding profiles to satisfy the requirements of both strength (safety during cyclones and storms) and economy. This thesis presents the details of large scale experimental studies undertaken and the results including the criterion for the splitting/fracture failure of high strength steel cladding systems. It describes the many advances made in the finite element modelling of crest-fixed steel cladding systems including the effects of localised pull-through and dimpling failures. Finally, it presents a simple design method for trapezoidal steel cladding systems under wind uplift or suction loading.
|
Page generated in 0.0979 seconds