A functionally-graded Al(subscript)2TiO(subscript)5/ZrO(subscript)2-Al(subscript)2O(subscript)3 (AT/zirconia-alumina) composite has been successfully synthesized by an infiltration process involving an alpha-Al(subscript)2O(subscript)3-ZrO(subscript)2 (90:10 by weight) green body and a solution containing titanium chloride. The mass gain after infiltration has been used to estimate the amount of new phase introduced into the system. The phase composition character of the functionally-graded material (FGM) has been determined by x-ray diffraction. The Rietveld "whole pattern" refinement method was applied to diffraction patterns of the sample which were collected from the surface and at several depths which were made by polishing away the material. Absolute weight fraction determination using the Rietveld external standard method showed that the concentration of AT reduces linearly from the surface to the core. In contrast, the alpha-alumina content increases with depth in a complementary manner. Low level amorphous phase was also observed. Other functionally-graded microstructural profiles examined were x-ray characteristic line intensity of Ti, Ti dot-mapping, and alpha-alumina grain size. The FGM also exhibits graded character in both thermal and mechanical properties, i.e. thermal expansion, microhardness, and Young's modulus. The thermal expansion coefficient (TEC) of the FGM increased with polishing-depth and approached that of the zirconia-alumina reference sample at a depth of 0.5 mm. / Relatively lower thermal expansion and softer surface layer in comparison to those of the core (TEC value of 5.9 x 10(subscript)-6 degrees celsius(subscript)-1 and microhardness of 6 GPa compared to 7.4 x 10(subscript)-6 degrees celsius(subscript)-1 and 12 GPa, respectively) render possibilities to implement the material to which thermal shock resistance surface but hard core, such as a metal melting crucible, are required. Load-dependent microhardness was obviously observed on the surface of the material but only slight dependence was observed in the core. This observation indicated that the material exhibit "quasi-ductile" surface but brittle core. In comparison to the reference specimen, the FGM displayed damage-tolerance and remarkable machinability.

Propagation of cracks in functionally graded materials (FGMs) under cyclic loading was investigated via experiments and finite element (FE) analysis. Alumina-epoxy composites with an interpenetrating-network structure and tailored spatial variation in composition were produced via a multi-step infiltration technique. Compressed polyurethane foam was infiltrated with alumina slip. After foam burn-out and sintering, epoxy was infiltrated into the porous alumina body. Non-graded specimens with a range of compositions were produced, and elastic properties and fatigue behaviour were characterised. An increase in crack propagation resistance under cyclic loading was quantified via a novel analytical approach. A simulation platform was developed with the commercial FE package ANSYS. Material gradient was applied via nodal temperature definitions. Stress intensity factors were calculated from nodal displacements near the crack-tip. Deflection criteria were compared and the local symmetry criterion provided the most accurate and efficient predictions. An automated mesh-redefinition algorithm enabled incremental simulation of crack propagation. Effects of gradient and crack-geometry parameters on crack-tip stresses were investigated, along with influences of crack-shape, crack-bridging, residual stresses and plasticity. The model provided predictions and data analysis for experimental specimens. Fatigue cracks in graded specimens deflected due to elastic property mismatch, concordant with FE predictions. In other FGMs, thermal or plastic properties may dominate deflection behaviour. Weaker step-interfaces influenced crack paths in some specimens; otherwise effects of toughness variation and gradient steps on crack path were negligible. Crack shape has an influence, but this is secondary to that of elastic gradient. Cracks in FGM specimens initially experienced increase in fatigue resistance with crack-extension followed by sudden decreases at step-interfaces. Bridging had a notable effect on crack propagation resistance but not on crack path. Similarly, crack paths did not differ between monotonic and cyclic loading, although crack-extension effects did. Recommendations for analysis and optimisation strategies for other FGM systems are given. Experimental characterization of FGMs is important, rather than relying on theoretical models. Opportunities for optimization of graded structures are limited by the properties of the constituent materials and resultant general crack deflection behaviour.

The main aim of this study is to utilize a Jk-integral based computational method in order to calculate crack tip parameters for orthotropic functionally graded materials (FGMs). The crack is subjected to mixed mode thermal loading. Mixed mode thermal fracture analysis requires the calculation of mode-I and mode-II stress intensity factors (KI ,KII ). In addition to stress intensity factors, energy release rate and T-stress are calculated by means of Jk-integral. Jk-integral is defined as a line integral over a vanishingly small curve. Since it is difficult to deal with a line integral on a vanishing curve , Jk-integral is converted to a domain independent form containing area and line integrals by the help of plane thermoelasticity constitutive relations. Steady-state temperature distribution profiles in FGMs and the components of the Jk-integral are computed by means of the finite element method. In both thermal and structural analyses, finite element models that possess graded isoparametric elements are created in the general purpose finite element analysis software ANSYS. In the formulation of Jk-integral, all required engineering material properties are assumed to possess continuous spatial variations through the functionally graded medium. The numerical results are compared to the results obtained from Displacement Correlation Technique (DCT). The domain independence of Jk-integral is also demonstrated. The results obtained in this study show the effects of crack location and material property gradation profiles on stress intensity factors, energy release rate and T-stress.

Functionally graded materials (FGMs) are composites that have continuously varying material properties, which eliminate undesirable stress concentrations that might otherwise occur in layered composites. The concept of inhomogeneously varying properties is observed in nature; examples include bones, teeth, shells and timber. Modern engineering applications of FGMs include thermal barrier coatings, wear-resistant coatings, biomedical implants and MEMS devices. Syntactic foams, particle filled nano-composites are examples of inhomogeneous materials of current interest. Analyses and experiments available in the literature have focused on characterizing the inhomogeneous material modulus and density variations. Common techniques employed are nano-indentation and wave propagation studies. There are a few fracture mechanics analyses and experiments available in the literature; most of which are devoted to measuring the fracture toughness of graded materials. A few fracture analyses of graded materials are devoted to deriving asymptotic stress, strain and displacement fields around stationary and steadily growing cracks in inhomogeneous materials. Only a few studies exist that deal with understanding the effect of material property inhomogeneity on the spontaneous crack propagation. In the present thesis the effect of material property inhomogeneity on the dynamic fracture mechanics of cracks in FGMs is described. Numerical analysis of the elastodynamic initial boundary value problem is performed using a spectral scheme. Spectral scheme is a special numerical technique developed to simulate spontaneous, planar crack propagation in a variety of materials. The method is numerically efficient as it can be implemented on parallel machines with ease. The numerical scheme is versatile and can handle any state-and rate-dependent traction-separation laws (cohesive zone models) or frictional laws. Spectral scheme has successfully been used in simulating intersonic crack propagation, earthquake slip dynamics and also direct silicon wafer bonding process used in realizing 3D MEMS structures. In the present work, the spectral formulation accounts for the inhomogeneous variation in the material wave speeds in the medium. The effect of inhomogeneity on spontaneous crack propagation due to in-plane mixed-mode loading is also addressed here. A parametric study has been performed by varying the inhomogeneity length scales independently in the top and bottom half-spaces. The effect of inhomogeneity in shear wave speed on the dynamic stress intensity factors (SIFs) of a crack propagating in a quasi-steady-state along the interface between the two functionally graded half-spaces is studied. A symmetric hardening FGM offers the maximum fracture resistance, while the fracture resistance is minimum for a symmetric softening FGM. Our simulation shows that increasing the inhomogeneity in the wave speed leads to eliminate the overshoot in the dynamic stress intensity factor. The magnitude of the steady-state (long-time) SIF increases indicating an increase in the fracture resistance. The effect of the inhomogeneous wave speed on the mode-3 crack propagation characteristics is demonstrated by taking snapshots of the crack opening at a time interval. The magnitude of the crack sliding displacement is found to increase with increase in the inhomogeneity. The effect of the material property inhomogeneity on the mode-1 crack propagation is simulated to track the crack opening displacements. The inhomogeneity is assumed to be symmetric about the weak-plane. Our spectral scheme developed here for functionally graded material with exponential variation in the material properties is capable of simulating independent bimaterial combinations. When the graded material becomes progressively stiffer and denser (hardening), the crack opening displacement in reduced, indicating an increase in the fracture resistance. On the other hand, for the softening FGMs the crack opening displacement increases indicating a reduction in fracture toughness. It is noted that the cohesive fracture resistance on the weak-plane remains same in all the FGMs.