Orientador: Prof. Dr. Alfeu Joãozinho Sguarezi Filho / Dissertação (mestrado) - Universidade Federal do ABC, Programa de Pós-Graduação em Engenharia Elétrica, 2015. / This research project presents the active and reactive power control of the Doubly Fed Induction Generator (DFIG) employing fuzzy logic for a wind power generation system, the proposed controller is a Fuzzy Logic Controller Takagi Sugeno type (TS FLC) which determines the rotor voltage by the rules base dened by a linear combination of the membership sets of the rotor current error, that reduces the complexity of the structure and consequently a lower computational cost and its easy to implement on a experimental set compared to other controllers such as Fuzzy Mamdani type. System control is accomplished using Stator Flux Field Oriented Control with Space Vector Modulation and computer simulation using mathematical models implemented in Matlab/Simulink. The results indicates that the FLC TS could be an interesting alternative to conventional controllers in the power control of the DFIG during normal operation conditions and under balanced voltage sags conditions.

Orientador: Dr. Alfeu J. Sguarezi Filho / Dissertação (mestrado) - Universidade Federal do ABC, Programa de Pós-Graduação em Engenharia Elétrica, 2014. / Devido as preocupações com a redu¸c¿ao do uso dos recursos f'osseis e das emiss¿oes de CO2 ocasionadas pelos mesmos, o interesse no uso de energias renov 'aveis aumentou, sendo uma destas fontes a energia e'olica. O Gerador de Indu¸c¿ao de Rotor Bobinado (GIRB) tem demonstrado ser uma ferramenta capaz de otimizar o uso da energia e'olica, dada a sua alta efici¿encia, rentabilidade e robustez mec¿anica, ainda assim 'e necess'ario superar os numerosos desafios que est¿ao presentes nesta tecnologia, tais como qualidade da pot¿encia, estabilidade da rede, entre outros. O objetivo desta pesquisa se concentra no estudo de t'ecnicas de controle de pot¿encia fornecida pelo GIRB aplicado a sistemas de gera¸c¿ao e'olica. No presente caso, o sistema de gera¸c¿ao 'e composto por um GIRB com seu estator conectado diretamente 'a rede e seu rotor 'e conectado 'a rede atrav'es de um conversor bidirecional. Prop¿oe-se estudar o m'etodo de controle direto de torque (CDT) com emprego de controladores PI e por modos deslizantes (SMC) mais PI. O controle direto de torque 'e uma t'ecnica de alto desempenho din¿amico e possibilita o controle independente do torque e fluxo do gerador o que possibilitar'a o controle das pot¿encias ativa e reativa do GIRB. Da mesma forma, 'e estudado o conversor para o processamento da energia gerada. As simula¸c¿oes baseadas em modelos matem'aticos destes m'etodos de controle foram revistos, analisados e comparados com as simula¸c¿oes de textos de refer¿encia. Resultados experimentais obtidos em uma bancada validaram o prot'otipo proposto. / Due to concerns about reducing the use of fossil resources and the CO2 emissions caused by them, interest in the use of renewable energy increased, one of these sources is wind energy. The Wound Rotor Induction Generator (WRIG) has been proved to be a tool to optimize the use of wind energy, given its high efficiency, profitability and mechanical robustness, it is still necessary to overcome the many challenges that are present in this technology, such as power quality, grid stability, among others. This research focuses on the study of control techniques for power supply by WRIG applied to wind generation systems. In this case, the generation system consists of a stator WRIG is connected directly to the electrical network and its rotor too, but via a bidirectional converter. It is proposed to study the method of direct torque control (DTC) with the use of PI and sliding mode controllers (SMC) more PI. The direct torque control is a technique of high dynamic performance and enables independent control of torque and flux generator, which will enable the control of active and reactive power ofWRIG. Likewise, it is studied the converter for processing the generated power. The simulations based on mathematical models of these control methods were reviewed , analyzed and compared with simulations of reference texts . Experimental results obtained on a bench validated the proposed prototype.