Thesis (Ph. D.)--University of Washington, 2004. / Vita. Includes bibliographical references (p. 305-324).

Thesis (M.S. - Geology and Mineralogy)--University of Arizona. / Bibliography: leaves 69-70.

Thesis (M.S.)--University of Wisconsin--Madison, 1967. / eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references.

Thesis (Ph. D.)--University of Wisconsin--Madison, 1980. / Typescript. Vita. Description based on print version record. Includes bibliographical references (leaves 142-149).

Thesis (M.S.)--University of Missouri-Columbia, 2006. / The entire dissertation/thesis text is included in the research.pdf file; the official abstract appears in the short.pdf file (which also appears in the research.pdf); a non-technical general description, or public abstract, appears in the public.pdf file. Title from title screen of research.pdf file viewed on (February 7, 2007) Includes bibliographical references.

No description available.

Thesis (Ph.D.)--University of Delaware, 2009. / Principal faculty advisor: James E. Pizzuto, Dept. of Geological Sciences. Includes bibliographical references.

Abstract This study was aimed at introducing multistage filtration (MSF) (a combination of slow-sand filtration (SSF) and pretreatment system - horizontal flow roughing filter (HRF)) as an alternative water treatment technology to the conventional one. A pilot- plant study was undertaken to achieve this goal. Evaluating the MSF performance vs. the existing conventional system in removing selected physical and chemical drinking water quality parameters together with the biological water quality improvement by the MSF without chemical use was done. Evaluation of the effectiveness of the MSF system utilizing locally available material, i.e. gravel, improved agricultural waste (charcoal maize cobs) and broken burnt bricks as pretreatment filter material was also done The benchmark was the Kenya Bureau of Standards (KEBS) values for the selected parameters. Results showed that with proper design specifications, MSF systems perform better than conventional systems under similar conditions of raw water quality and environmental conditions. The tested locally available materials can also be effectively used as pretreatment media with each allowing a filter run greater than 82 d and therefore could serve as alternatives where natural gravel is not readily available. With special reference to the bacteriological quality improvement, the MSF greatly improved the bacteriological quality of the water recording removal efficiencies of over 99% and 98% respectively for E. coli and total coliforms. Despite the observed performance, MSF should be complemented with chlorination as a final buffer against water-borne diseases. However, in this case, the dosing will be greatly reduced when compared to the conventional system.

The Standard Penetration Test (SPT) is the most widely used in-situ soil test in the world. "Large Penetration Test" (LPT) is a term used to describe any scaled up version of the SPT. Several types of LPT have been developed around the world for the purpose of characterizing gravel deposits, as SPT blow counts are less reliable in gravels than in sands. Both tests suffer from the lack of a reliable means of determining transferred energy. Further, the use of LPT blow counts is generally limited to calculation of equivalent SPT blow counts using correlation factors measured in sands. Variation of LPT blow counts with grain size is assumed to be negligible. This research shows that safety hammer energies can be reliably estimated from measurements of hammer impact velocity for both SPT and LPT. This approach to determining transferred energy is relatively simple, and avoids the primary limitation of existing methods, which is the inability to calibrate the instrumentation. Transferred energies and hammer impact velocities are collected from various sources. These data are used to determine the ratio between the hammer kinetic energy and the transferred energy (energy transfer ratio, ETR), which is found to follow a roughly Normal distribution for the various hammers represented. An assessment of uncertainty is used to demonstrate that an ETR based approach could be superior to existing energy measurement methods. SPT grain size effects have primarily been characterized as the variation of an empirical relative density correlation factor, (CD)SPT, with mean grain size. In this thesis, equivalent (CD)LPT data are back-calculated from measured SPT-LPT correlation factors (CS/L). Results of a numerical study suggest that SPT and LPT grain size effects should be similar and related to the ratio of the sample size to the mean grain size. Based on this observation, trend-lines with the same shape as the (CD)SPT trend-line are established for the back-calculated (CD)LPT data. A method for generating the grain size effect trend-line for LPT is then proposed. These trend lines provide a rational approach to direct interpretation of LPT data, or to improved prediction of equivalent SPT blow counts.

Graduation date: 1986