The production of multi-component cement from clinker and two additives such as trass and blast furnace slag has now spread throughout the world. These additives are generally interground with clinker to produce a composite cement of specified surface area. The grinding stage is of great importance as it accounts for a major portion of the total energy consumed in cement production and also as it affects the quality of composite cements by the particle size distribution of the individual additives produced during grinding. This thesis study was undertaken to characterize the breakage properties of clinker and the additives trass and slag with the intention of delineating their grinding properties in separate and intergrinding modes. Single particle breakage tests were conducted by means of a drop weight tester in order to define an inherent grindability for the clinker and trass samples in terms of the median product size ( ). In addition, a back-calculation procedure was applied to obtain the breakage rate parameters ( ) of perfect mixing ball mill model using industrial data from a cement plant. Kinetic and locked-cycle grinding tests were performed in a standard Bond mill to determine breakage rates and distribution functions for clinker, trass and slag. Bond work indices of these cement components and of their binary and ternary mixtures were determined and compared. Attempts were made to use back-calculated grinding rate parameters to simulate the Bond grindability test. The self-similarity law was proved to be true for clinker and trass that their shapes of the self-similarity curves are unique to the feed material and independent of the grinding energy expended and overall fineness attained. The self-similar behaviour of tested materials will enable process engineers to get useful information about inherent grindability and energy consumption in any stage of the comminution process. The parameters, and indicating the degree of size reduction were defined with different theoretical approaches as a function of energy consumption by using single particle breakage test data of clinker and trass. The breakage distribution functions were found to be non-normalizable. On the other hand, the breakage rate functions were found to be constant with respect to time but variable with respect to changing composition in the Bond ball mill. These variations are critical in computer simulation of any test aiming to minimize the experimental efforts of the standard procedure. As a result of the back calculation of breakage rate parameters for clinker and trass samples in the Bond mill, no common pattern was seen for the variation of the rate parameters. Therefore, computer simulation of the Bond grindability test did not result in an accurate estimation of the Bond work index.

Aitik is a large copper porphyry type deposit located in northern Sweden, currently exploited at an annual rate of approximately 45Mt. The ore's exceptionally low head grade of 0.22 % Cu and varying degrees of hardness across the entire deposit pose challenges to the two fully autogenous grinding lines, each of which comprises a 22.5 MW primary autogenous mill in series with a pebble mill. The variability in ore grindability frequently leads to fluctuations in mill throughput.  Within the framework of a geometallurgical approach, the present study investigated the relationships between ore grindability and modal mineralogy. For this purpose, drill core samples from different lithologies were subjected to Boliden AB's in-house grindability tests. This laboratory-scale autogenous grinding test generates a grindability index Ks mainly related to abrasion breakage, which is a significant breakage mechanism within autogenous mills. The test results suggested divergent degrees of grindability within and across the selected rock types. Furthermore, subsequent sieve analyses identified a relationship between the grindability index, PSD, and the proportions of fines generated by abrasive grinding. A combination of scanning electron microscopy, X-ray powder diffraction, and X-ray fluorescence analyses was performed for the grinding products and bulk mineral samples. The resulting mineralogical and elemental properties were correlated to the parameters from the grindability tests. It was shown that the main mineral phases, such as plagioclase, quartz, and micas, correlate well with the grindability indices. Similar correlations were found regarding the sample's chemical composition, attributable to the main mineral phases. Derived from the previous findings, two exemplary linear empirical models for the calculation of grindability based on either mineral contents or chemical composition were presented. Careful examination of the mineralogical data revealed that the prevalent abrasion breakage mechanism leads to constant and continuous removal of mineral particles from the sample's surface. No indications for a preferential abrasion of any mineral phases were found.  A further inverse correlation between the sample's calculated average weighted Mohs hardness based on modal mineralogy and the grindability index Ks was established. Hence, it was proposed that a higher Mohs hardness results in a finer grinding product, oppositional to the Ks-values. Since Ks can be interpreted as a measure of abrasiveness, it can be stated that abrasiveness decreases with an increasing average sample hardness and vice versa.  Moreover, mineral liberation information provided by scanning electron microscopy was associated with the parameters mentioned earlier. It was determined that different degrees of mineral liberation were reached within specific particle size classes. The identified relationships between grindability, modal mineralogy, and element grades may help Boliden develop a predictive throughput model for Aitik to be integrated into the mine's block model. Based on this information, a strategy for smart blending could be developed, where run of mine material from ore blocks of varying grindabilities could be blended to attain the target plant throughput.

Efficient measurement methods for comminution properties are an important prerequisite for testing the variability of an ore deposit within the geometallurgical context. This involves the investigation of effects of mineralogy and mineral texture on the breakage of mineral particles. Breakage properties of mineral particles are crucial for the liberations of minerals and the energy required for that. For process optimization and control purposes, comminution indices are often used to map the variation of processing properties of an entire ore body (e.g. Bond work index). Within the geometallurgical approach this information is then taken up when modelling the process with varying feed properties. The main focus of this thesis work has been to develop a comprehensive geometallurgical testing framework, the Geometallurgical Comminution Test (GCT), which allows the time and cost efficient measurement of grinding indices and their linkage to mineralogical parameters (e.g. modal mineralogy or mineral texture, mineral liberation). In this context a small-scale grindability test has been developed that allows estimating the Bond work index from single pass grinding tests using small amounts of sample material. Verification of the evaluation method and validation was done with different mineral systems. For selected samples the mineral liberation distribution was investigated using automated mineralogy. By transferring the energy-size reduction relation to energy – liberation relation new term liberability has been established. As part of the experimental investigations, mineralogical parameters and mineral texture information were used for predicting breakage and liberation properties. Patterns for describing the breakage phenomena were established for a set of iron oxide ore samples. The determined breakage patterns indicated that the specific rate of mineral breakage slows down when reaching the grain size of mineral particles, thus allowing maximizing mineral liberation significantly without wasting mechanical energy. / CAMM

The aim of this thesis was to summarize and assess the possibility of using recycled glass in the manufacture of blended portland cements. Work was focused on examining the possibilities to improve pozzolanic properties of recycled glass with new milling processes. The formation of agglomerates material during the course of grinding and their subsequent effect on the hydration process of binders has been also examining. Part of the thesis was also focused on grindability of materials and determination of using separate or inters grinding.