Water polluted by metals and phosphates can be hazardous to both the environment and human health. The aim of this study was used to improve understanding of the adsorption properties of low-cost, green adsorbents for removal of pollutants from aqueous solution. Biochar was used as an adsorbent, which was produced from the gasification of pine wood waste and the fast pyrolysis of Douglas fir. Biochar is a bio-renewable product that can easily be modified, and the cost is lower compared to other adsorbents like activated carbon. The gasifier produced biochar was modified by coating the biochar surface with chitosan. Douglas fir biochar, produced by pyrolysis, was used in Mg/Al-layered double hydroxides (LDHs) and magnetization modifications. The Mg/Al-LDHs were prepared by co-precipitation using solutions of Mg and Al salts and NaOH treatment. The magnetization modification of the biochar was prepared by magnetite (Fe3O4) precipitation onto the biochar’s surface from Fe2+/Fe3+ solution upon NaOH treatment. Chapter I provides an introduction into biochar production, uses, and modification methods. Chapter II is a study of the aqueous adsorption Cu2+ and Cd2+ metals using chitosan coated and uncoated gasifier biochars. Chapter III focused on the removal of phosphate from aqueous solutions. Different ratios of Mg:Al in the LDHs were used to test the ratio’s affect on the adsorption properties of the modified adsorbents. Chapter IV describes the removal of phosphate from water using LDH modified biochars that are magnetized. This study looks at how the order in which the modifications were done influences the biochars adsorption ability. The surface chemistry and composition of each biochar in chapters II-IV were examined by SEM, SEM-EDX, TEM, PZC, XRD, elemental analysis, and surface area measurements. Each biochar’s adsorption ability was studied by pH effects, kinetics, and maximum capacity for the analyte.

The reversible and topotactic insertion of guest species within layered host lattices, known as intercalation is a widely studied phenomena. The Layered Double Hydroxides (LDHs) or Anionic Alloys are important class of layered solids with its own distinct ion-exchange host-Guest Chemistry. The LDH structure may be derived from that of Brucite, Mg(OH)2, by random isomorphous substitution of Mg2+ ions by trivalent cations like Al3+, Ga3+ etc. This substitution leaves an excess positive charge on the layers, which is compensated by interlamellar anions. These ions are exchangeable and thus new functionalities can be introduced to ion exchange reactions. Insertion of neutral, non-polar or poorly water-soluble guest molecules remains a challenge. In the present study, two methodologies were adopted to extend the host-guest chemistry of LDHs to neutral and non-polar species, first by using Hydrophobic interaction and second, charge transfer (CT) interaction as driving force. Hlydrophobic interaction as driving force involves functionalization of the Mg-Al-LDH galleries as bilayers, thus covering the essentially hydrophilic interlamellar space of the LDH to one that is hydrophobic and able to solubilize neutral molecules like Anthracene. CT interaction as driving force, involves pre-functionalization of the galleries of the LDH with a donor species e.g. 4-aminobenzoic acid by conventional ion exchange methods to form a LDH-donor intercalated compound. This compound can selectively adsorb acceptor species like Chloranil, Tetracyanoquinodimethane etc. into the interlamellar space of the solid by forming donor-acceptor complexes. The confined donor-acceptor complexes have been characterized by X-Ray Diffraction, UV-Visible, Fourier Transformed Infra-Red and Raman Spectroscopy, Molecular Dynamics Simulations were able to reproduce the experimental results. One dimensional gold nanostructure like nanorods (AuNRs) have received great attention due to their size dependent optical properties, Extending these applications requires assembling the AuNRs into one-, two- and if possible three-dimensional architectures. Several approaches have been developed to assemble AuNRs in two-orientation modes namely end-to-end and side-to-side. The present study self-assembly of the AuNRs has been achieved by anchoring β-cyclodextrin (β-CD) cavities to the nanorods surface. The host-guest chemistry of β-CD has been exploited to assemble the AuNRs. Our strategy was to use a guest molecule that is capable to link β-CD into 1:2 host-guest fashions to link up two β-CD capped nanorods. The guest molecule chosen for the present study was 1,10-phenanthroline. Linkage between the ends of rods leading to V-shaped rods dimmer assembly and side-to-side assembly was achieved by varying the extent of cyclodextrin capping of the AuNRs followed by the addition of linker, 1,10-phenanthroline. The formation of the assembly was characterized using UV-Visible-Near-IR Spectoscopy and Transmission Electron Microscopy.

The interconversion of α- and β-Ni(OH)₂ was studied using cyclic voltammetry and dynamic electrochemical impedance (dEIS). Holding experiments were done at 0.5 V, 0.6 V, 0.8 V and 1.0 V while subsequent cathodic holds were applied in selected experiments at -0.1, -0.2, -0.25 V. The number of thickness of Ni(OH)₂ formed increased with increasing anodic potential. After α-Ni(OH)₂ was formed (< 0.5 V), it was easily reduced by sweeping down to -0.15 V. However, sweeping further (> 0.5 V) resulted in its "irreversible" conversion to β-Ni(OH)₂. Since β-Ni(OH)₂ was not reduced by sweeping to -0.15 V, the current, capacitance and the conductance at the α-Ni(OH)₂ peak (at 0.2 V) decreased as a result. However, β-Ni(OH)₂ was shown to be reducible during potential holds at -0.2 V or lower. In contrast, holding at -0.1 V only resulted in partial reduction. Eventually, a link was established between the reduction of β-Ni(OH)₂ and hydrogen evolution. The relatively slow reduction of the β-Ni(OH)₂ to metallic nickel appears to inhibit the capacitance increase at -0.15 V which occurs when the potential is kept under 0.5 V. The retention of a low capacitance while β-Ni(OH)₂ persists suggests a blocking mechanism. A concerted adsorption-desorption step which generates adsorbed hydrogen prior to hydrogen evolution was proposed. An exponential increase in current and capacitance occurred during the potential hold at -0.2 V. The capacitance increase suggests a reversal of the blocking (low capacitance at -0.15 V) caused by the persistence of β-Ni(OH)₂. Additionally, the exponential current decay during the hold at -0.2 V was significantly slower than the conversion of α- to β-Ni(OH)₂ at 0.8 V. This further demonstrates the possibility of a slow step involving surface blocking during the reduction of β-Ni(OH)₂. These observations provide new information on the mechanism and kinetics of the interconversion of α-Ni(OH)₂ into β-Ni(OH)₂ and the interaction of the latter in the hydrogen evolution reaction. / Graduate

Lignin is one of the most abundant and underutilized biopolymers on earth. Primarily composed on three monolignol units (sinapyl, coniferyl, and p-coumaryl alcohol), lignin is formed through a radical pathway resulting in an assortment of linkages, of which the β-O-4 linkage is the most prevalent (up to 60% in some hardwood species). In planta, lignin plays an important role in water transport and in protecting plants from chemical and biological attack. Traditional attempts to depolymerize lignin have focused on the cleavage of β-O-4 linkages via thermal or reductive routes. However these pathways lead to low-value, unstable product mixtures. Moreover, typical product yields are low and the highly corrosive reaction medium results in added expense. More recently, catalytic oxidations have been studied as a viable means to lignin utilization. The present work will review the state-of-the-art of lignin oxidations, and focus on stoichiometric and catalytic attempts to oxidize lignin and lignin model compounds in order achieve selective stepwise depolymerization of lignin. Specifically, activated dimethyl sulfoxides and LDH catalysts were evaluated for lignin and/or lignin model compound oxidations leading, in some cases, to unexpected products.

A brief introduction to the current state of research in the Origins of Life field is given in Part I of this work. Part II covers original research performed by the author and co-workers. Layered Double Hydroxide (LDH) systems are anion-exchanging clays that have the general formula M(II)xM(III)(OH)(2x+2)Y, where M(II) and M(III) are any divalent and trivalent metals, respectively. Y can be nearly any anion, although modern naturally occuring LDH systems incorporate carbonate (CO32-), chloride (Cl-), or sulfate (SO42-) anions. Intercalated cobalticyanide anion shows a small yet observable deviation from local Oh symmetry causing small differences between its oriented and non-oriented infrared spectra. Nitroprusside is shown to intercalate into 2:1 Mg:Al LDH with decomposition to form intercalated ferrocyanide and nitrosyl groups of an unidentified nature. The [Ru(CN)6]4- anion is shown to intercalate into layered double hydroxides in the same manner as other hexacyano anions, such as ferrocyanide and cobalticyanide, with its three-fold rotational axis perpendicular to the hydroxide sheets. The square-planar tetracyano-nickelate(II), -palladate(II), and platinate(II) anions were intercalated into both 2:1 and 3:1 Mg:Al layered double hydroxides (LDH). The basal spacings in the 2:1 hosts are approximately 11 Å, indicating that the anions are inclined approximately 75 degrees relative to the hydroxide layers, while in the 3:1 hosts the square-planar anions have enough space to lie more nearly parallel to the LDH cation layers, giving basal spacings of approximately 8 Å. It has been found that the LDH Mg2Al(OH)6Cl catalyzes the self-addition of cyanide, to give in a one-pot reaction at low concentrations an increased yield of diaminomaleonitrile and in addition, at higher ($0.1M) concentrations, a purple-pink material that adheres to the LDH. We are investigating whether this reaction also occurs with hydrotalcite itself, what is the minimum effective concentration of cyanide, and what can be learned about the products and how they compare with those reported at high HCN concentrations in the absence of catalyst.

Os materiais híbridos orgânico-inorgânicos constituem uma classe especial compostos, obtidos pela combinação adequada entre duas ou mais fases (orgânica e inorgânica), que têm recebido muita atenção nos últimos anos. Quando combinados em escala molecular, os nanocompósitos formados promovem o sinergismo entre as propriedades destas fases podendo produzir materiais com características e propriedades únicas e inusitadas que não são encontradas nas partes individuais. As particularidades dos novos materiais podem resultar em aplicações como melhoria de propriedades mecânicas, da estabilidade térmica, permeabilidade de gases, retardadores de chama, polímeros eletrólitos, dentre outras. As siliconas aniônicas são materiais poliméricos utilizados como agentes dispersantes, espumantes, emulsificantes e complexantes promovendo a compatibilidade entre a silicona e outros polímeros, permitindo a formulação de géis estáveis e limpos com aplicações principalmente na indústria de cosméticos. Hidróxidos Duplos Lamelares (HDL) são materiais cuja estrutura lamelar é constituída de camadas de um hidróxido duplo carregadas positivamente, com ânions hidratados no domínio interlamelar. A esfoliação de HDL é um processo que permite a separação em escala nanométrica das contrapartes inorgânica (do hidróxido duplo) do ânion interlamelar (que pode ser orgânico ou não). O foco do presente trabalho é a preparação e a caracterização de materiais híbridos orgânico-inorgânicos através da utilização de siliconas aniônicas funcionalizadas com os grupos fosfato, sulfato, ftalato e succinato como matriz orgânica e as lamelas esfoliadas de um HDL do sistema Zn-Al como aditivo inorgânico. Novos compósitos foram preparados, em blocos e na forma de filmes, a partir da interação entre as siliconas aniônicas e diferentes cargas do HDL esfoliado utilizado como aditivo. Os compósitos apresentaram modificações em suas características como aumento da estabilidade térmica, resistência mecânica e maleabilidade comparada às siliconas puras. Tais características podem ser aproveitadas para aplicações até então inexploradas por estes materiais. / Hybrid composites are a class of materials obtained by the appropriate combination of two or more phases (organic and inorganic), which have nowadays received a lot of attention. When these composites are combined at the molecular scale, the resulting nanocomposites resulting promote the synergism among the properties of the lonely phases and can then produce materials with unique and unusual characteristics and properties not found in individual species. The particularities of the new materials can result in applications such as the improvement of mechanical properties, thermal stability, permeability of gases, flame retarder, polymeric electrolytes, etc. Anionic silicones are polymeric materials used as dispersant, foaming, emulsifiant and complexant agents capable of promoting compatibility among the silicone and the other polymers, thus allowing the formulation of stable and clean gels for applications mainly in the cosmetic industry. Layered double hydroxides (LDH) are lamellar materials constituted of positively charged layers of a double hydroxide, with hydrated anions in the interlayer domain. The exfoliation of LDH is a process that allows to separate the inorganic sheets (of the double hydroxide) from the interlayer anion (which can be organic or not) at nanometric scale. The present work focus on the preparation and the characterization of organic-inorganic hybrid materials by using anionic silicones functionalized with the phosphate, sulfate, ftalato and succinate groups (organic matrix) and the layer of the exfoliated LDH of the Zn-Al system as the inorganic additive. New composites in block and films forms were prepared, starting from the interaction between the anionic silicones and different loads of LDH exfoliated as additive. The composites presented modifications in their characteristics such as the increase of thermal stability, mechanical resistance and malleability compared to pure silicones. Such characteristics can be used for applications in unexplored areas of these materials.

Intermittent renewable energy sources, such as solar and wind, will only be viable if the electrical energy can be stored efficiently. It is possible to store electrical energy cleanly by splitting the water into oxygen (a clean byproduct) and hydrogen (an energy dense fuel) via water electrolysis. The efficiency of hydrogen production is limited, in part, by the high kinetic overpotential of the oxygen evolution reaction (OER). OER catalysts have been extensively studied for the last several decades. However, no new highly active catalyst has been developed in decades. One reason that breakthroughs in this research are limited is because there have been many conflicting activity trends. Without a clear understanding of intrinsic catalyst activity it is difficult to identify what makes catalysts active and design accordingly. To find commercially viable catalysts it is imperative that electrochemical activity studies consider and define the catalyst’s morphology, loading, conductivity, composition, and structure. The research goal of this dissertation is twofold and encompasses 1) fundamentally understanding how catalysis is occurring and 2) designing and developing a highly active, abundant, and stable OER catalyst to increase the efficiency of the OER. Specifically, this dissertation focuses on developing methods to compare catalyst materials (Chapter II), understanding the structure-compositional relationships that make Co-Fe (oxy)hydroxide materials active (Chapter III), re-defining activity trends of first row transition metal (oxy)hydroxide materials (Chapter IV), and studying the role of local geometric structure on active sites in Ni-Fe (oxy)hydroxides (Chapter V). As part of a collaboration with Proton OnSite, the catalysts studied are to be integrated into an anion exchange membrane water electrolyzer in the future. This dissertation includes previously published and unpublished co-authored material. / 10000-01-01

Hidróxidos duplos lamelares (LDHs) são uma classe materiais lamelares com fórmula química [M_(1-x)^II M_x^III (OH)_2 ] [A^(n-)]_(x/n).yH_2 O (onde M^II e M^III são metais di e trivalentes, respectivamente) formados pelo empilhamento de camadas positivamente carregadas de hidróxidos metálicos intercaladas por espécies aniônicas A^(n-). Este trabalho descreve uma estratégia inédita para a produção de nanotubos de LDHs autossuportados (Ø 20 nm e comprimentos >= 100 nm) através da coprecipitação de Zn^(2+), Al^(3+) e Eu^(3+) em pH controlado e sua auto-organização sobre micelas cilíndricas do surfactante Plurônico® P-123. A subsequente extração destes agentes estruturantes através de lavagem com metanol resulta em uma rede de nanotubos cilíndricos, ocos e interconectados, formados pela deposição de multicamadas de hidróxidos duplos intercalados pela molécula sensibilizadora ácido benzeno-1,3,5-tricarboxílico (ácido trimésico, BTC). A combinação de Eu3+ nas camadas de hidróxidos e BTC no meio interlamelar resulta em nanotubos com propriedades luminescentes, demonstrando de maneira notável como modificações químicas e morfológicas nos LDHs podem levar ao remodelamento das suas propriedades físico-químicas e consequentemente direcionar suas aplicações de maneira desejável. / Layered double hydroxides are a class of lamellar compounds with chemical formula [M_(1-x)^II M_x^III (OH)_2 ] [A^(n-)]_(x/n).yH_2 O (with M^II and M^III being di and trivalent metals, respectively) that are formed by the stacking of positively charged mixed-valence metal hydroxide sheets intercalated by anionic species A^(n-). This work describes a new strategy for the synthesis of self-supporting mesoporous LDH nanotubes (Ø 20 nm and length >= 100 nm) by coprecipitation of Zn^(2+), Al^(3+) and Eu^(3+) around non-ionic worm-like micelles of Pluronic® P-123 in controlled pH. Subsequent extraction of the structure-directing agent with methanol results in a network of interconnected, well-defined, multi-walled and hollow cylindrical LDH nanotubes intercalated by the sensitizing ligand BTC (1,3,5-benzenetricarboxilate). The combination of Eu^(3+) in the hydroxide layers and BTC in the interlayers results in nanotubes with luminescence properties in a notable demonstration on how chemical and morphological changes in LDHs can lead to materials with tuned physico chemical properties that can be tailored towards a range of applications.

No description available.

Chan, Mui. / Thesis (M.Phil.)--Chinese University of Hong Kong, 2009. / Includes bibliographical references. / Abstract also in Chinese. / Abstract --- p.i / Abstract (Chinese) --- p.iii / Declaration --- p.v / Acknowledgement --- p.vi / Table of Contents --- p.viii / List of Tables --- p.xiv / List of Figures --- p.xv / Chapter Chapter 1: --- Introduction / Chapter 1.1 --- Overview --- p.1 / Chapter 1.2 --- Soft-Chemistry --- p.7 / Chapter 1.2.1 --- Sol-Gel Method --- p.7 / Chapter 1.2.2 --- Co-precipitation --- p.9 / Chapter 1.2.3 --- Microemulsion --- p.10 / Chapter 1.3 --- Application of Hydrothermal/Solvothermal Methods in Materials Synthesis --- p.12 / Chapter 1.3.1 --- Fundamentals of Hydrothermal and Solvothermal Methods --- p.12 / Chapter 1.3.2 --- Advantages of Hydrothermal/Solvothermal Methods in contrast to Conventional Synthetic Approaches --- p.13 / Chapter 1.3.3 --- Hydrothermal and Solvothermal Preparation of Materials --- p.14 / Chapter 1.4 --- Application of Transition Metal Oxides As Functional Materials --- p.15 / Chapter 1.5 --- Aim and Scope of Work --- p.16 / Chapter 1.6 --- References --- p.17 / Chapter Chapter 2: --- Solvothermal and Hydrothermal Template Free Synthesis of ZnO Microspheres / Chapter 2.1 --- Introduction --- p.23 / Chapter 2.2 --- Experimental Section --- p.25 / Chapter 2.2.1 --- Synthesis of ZnO Microspheres by Solvothermal Method --- p.25 / Chapter 2.2.2 --- Synthesis of ZnO Microspheres by Hydrothermal Method --- p.26 / Chapter 2.2.3 --- Doping ZnO Microspheres with Silver or Gallium by Solvothermal Method --- p.26 / Chapter 2.2.4 --- Characterization --- p.27 / Chapter 2.2.5 --- Measurement of Photocatalytic Activity --- p.29 / Chapter 2.3 --- Results and Discussion --- p.30 / Chapter 2.3.1 --- X-Ray Diffraction Analysis --- p.30 / Chapter 2.3.1.1 --- ZnO-HT and ZnO-ST --- p.30 / Chapter 2.3.1.2 --- ZnO-ST: Effect of Different Concentrations of Zinc Acetate --- p.33 / Chapter 2.3.1.3 --- Doping ZnO-ST with Silver or Gallium --- p.34 / Chapter 2.3.2 --- SEM study --- p.36 / Chapter 2.3.2.1 --- ZnO-HT and ZnO-ST --- p.36 / Chapter 2.3.2.2 --- ZnO-HT-Different Volume Ratios of Ethylene Glycol to Water --- p.37 / Chapter 2.3.2.3 --- ZnO-ST --- p.39 / Chapter 2.3.2.3.1 --- Different Volume Ratios of Benzyl Alcohol to Ethylene Glycol --- p.40 / Chapter 2.3.2.3.2 --- Different Concentrations of Zinc Acetate --- p.41 / Chapter 2.3.2.3.3 --- Different Concentrations of Urea --- p.42 / Chapter 2.3.3 --- TEM Study --- p.44 / Chapter 2.3.3.1 --- TEM and HRTEM of ZnO-HT --- p.44 / Chapter 2.3.3.2 --- TEM and HRTEM of ZnO-ST --- p.45 / Chapter 2.3.3.3 --- TEM Images of Ga-Doped ZnO-ST --- p.47 / Chapter 2.3.3.4 --- TEM Images of Ag-Doped ZnO-ST --- p.49 / Chapter 2.3.4 --- Nitrogen Adsorption and Desorption --- p.50 / Chapter 2.3.5 --- X-Ray Photoelectron Spectroscopy --- p.52 / Chapter 2.3.5.1 --- XPS Study of ZnO-ST --- p.52 / Chapter 2.3.5.2 --- XPS Study of ZnO-HT --- p.54 / Chapter 2.3.5.3 --- XPS Study of Silver Doped ZnO-ST --- p.56 / Chapter 2.3.5.4 --- XPS Study of Gallium Doped ZnO-ST --- p.58 / Chapter 2.3.6 --- FR-IR Spectra --- p.60 / Chapter 2.3.7 --- Photocatalytic Activity on Degradation of Methylene Blue --- p.61 / Chapter 2.3.8 --- Proposed Formation Mechanism for ZnO-ST --- p.64 / Chapter 2.3.9 --- Proposed Formation Mechanism for ZnO-HT --- p.68 / Chapter 2.3.10 --- Optical Property of ZnO Microspheres --- p.69 / Chapter 2.4 --- Conclusion --- p.73 / Chapter 2.5 --- References --- p.74 / Chapter Chapter 3: --- Synthesis of Hierarchical Porous Lithium Niobate Submicrometer Rods / Chapter 3.1 --- Introduction --- p.79 / Chapter 3.2 --- Experimental Section --- p.81 / Chapter 3.2.1 --- Characterization --- p.82 / Chapter 3.3 --- Results and Discussion --- p.83 / Chapter 3.3.1 --- X-Ray Diffraction Analysis --- p.83 / Chapter 3.3.2 --- SEM Study --- p.86 / Chapter 3.3.2.1 --- Surfactants Dependent Morphologies Change --- p.86 / Chapter 3.3.2.2 --- Concentrations of CTAB --- p.87 / Chapter 3.3.2.3 --- Time Dependent Morphologies Change --- p.88 / Chapter 3.3.3 --- TEM Study --- p.91 / Chapter 3.3.5 --- XPS Analysis --- p.93 / Chapter 3.3.6 --- BET Analysis --- p.96 / Chapter 3.3.7 --- Proposed Formation Mechanism --- p.97 / Chapter 3.3.7.1 --- Effect of Microemulsion --- p.97 / Chapter 3.3.7.2 --- Effect of CTAB --- p.98 / Chapter 3.3.7.3 --- Ostwald Ripening --- p.99 / Chapter 3.3.7.4 --- Formation of LiNi3O8 --- p.101 / Chapter 3.4 --- Conclusion --- p.102 / Chapter 3.5 --- References --- p.103 / Chapter Chapter 4: --- Flower-Like α-Nickel Hydroxide synthesized by hydrothermal method / Chapter 4.1 --- Introduction --- p.106 / Chapter 4.2 --- Experimental Section --- p.108 / Chapter 4.2.1 --- Synthesis of Nickel Hydroxide by Hydrothermal Method --- p.108 / Chapter 4.2.2 --- Characterization --- p.109 / Chapter 4.3 --- Results and Discussion --- p.111 / Chapter 4.3.1 --- X-Ray Diffraction Analysis --- p.111 / Chapter 4.3.2 --- SEM Study --- p.115 / Chapter 4.3.3 --- TEM and HRTEM Study --- p.116 / Chapter 4.3.4 --- XPS Analysis --- p.117 / Chapter 4.3.5 --- FT-IR Analysis --- p.119 / Chapter 4.3.6 --- BET analysis --- p.120 / Chapter 4.3.7 --- Proposed Formation Mechanism of the Flower like α-Ni(OH)2 --- p.122 / Chapter 4.4 --- Conclusion --- p.123 / Chapter 4.5 --- References --- p.124 / Chapter Chapter 5: --- Conclusions and Future Work / Chapter 5.1 --- Conclusions --- p.127 / Chapter 5.2 --- Future work --- p.129