Thesis (Ph. D. in Interdisciplinary Studies: Environmental Management)--Vanderbilt University, May 2005. / Title from title screen. Includes bibliographical references.

Thesis (Ph. D.)--University of Maryland at College Park, 1995. / Vita. Includes bibliographical references (leaves 141-147).

Thesis (Ph. D.)--Oregon State University, 2010. / Printout. Includes bibliographical references (leaves 276-302). Also available on the World Wide Web.

Thesis (Ph. D.)--Dept. of Psychology. University of Missouri--Kansas City, 2004. / "A dissertation in community psychology." Advisor: Joseph B. Hughey. Typescript. Vita. Title from "catalog record" of the print edition Description based on contents viewed Frb. 23, 2006. Includes bibliographical references (leaves 355-370). Online version of the print edition.

The response of several plant species to heavy metal contaminated soils was evaluated using plant bioassays with a soil substrate. A natural soil was collected from Dinwiddie County, Virginia and soil analysis was performed. The plant species, Lolium multiflorum, setaria italica and Trifolium rep ens latum, Robinia pseudoacacia, Andropogon gerardi, Asclepias syriaca, Echinacea purpurea, Rudbeckia hirta and Festuca rubra were grown in to determine the response to cupric and cadmium chloride in soils (mg Cu/kg soil). A few plant species were grown in small pots in a plant growth chamber for 28 days using control, 10, 30, 100 and 300mg Cu or Cd/kg soil. Germination proved to be less sensitive than root length. S. italica had highest ECSOs. In eu 20.7 and 15.3 in Cd. All plant species were grown for 7 days in 0.3, 1.0, 3.0 10.0, and 30.0mg Cu/kg soil and in control. Germination was not effected by metal concentrations in most species (p=0.07-0.6), except T.repens latum, R. hirta and F. rubra at 30mg/kg (p=0.0007). Root length was significantly effected by Cu concentrations for almost all species (p=0.0001-0.0112). Setaria italica had the highest EC50 at 10.86mg/kg. Robinia pseudoacacia root length was not significantly affected by CU concentrations. The other species had EC50s ranging from 3.74-7.51mg/kg. Both inhibition and stimulation of root growth were observed. Preliminary studies regarding germination rates, fungicides and rangefinding are included. / Master of Science

The objective of this study is to identify and examine potential mechanisms of radionuclide transport as vapor at a high-level radioactive waste repository located in unsaturated fractured rock. Transport mechanisms and processes have been investigated near the repository and at larger distances. Transport mechanisms potentially important at larger distances include ordinary diffusion, viscous flow and free convection. Ordinary diffusion includes self and binary diffusion, Knudsen flow and surface diffusion. Pressure flow and slip flow comprise viscous flow. Free convective flow results from a gas density contrast. Transport mechanisms or processes dominant near the repository include ordinary diffusion, viscous flow plus several mechanisms whose driving forces arise from the non-isothermal, radioactive nature of high-level waste. The additional mechanisms include forced diffusion, aerosol transport, thermal diffusion and thermophoresis. Near a repository vapor transport mechanisms and processes can provide a significant means of transport from a failed canister to the geologic medium from which other processes can transport radionuclides to the accessible environment. These issues are believed to be important factors that must be addressed in the assessment of specfic engineering designs and site selection of any proposed HLW repository.

Methodologies for estimating hydraulic and solute transport properties of unsaturated, fractured rock are developed. The methodologies are applied to networks of discrete fractures for the purpose of estimating steady fluid flow rates and breakthrough curves of entrained solutes. The formulations employ the boundary integral method to discretize the outer rim of each fracture and to solve a two dimensional flow equation within fracture planes. A three dimensional variant of the two dimensional boundary integral method is used to calculate flow through a permeable matrix with embedded permeable fractures. Exterior and interior surfaces are discretized using boundary elements to account for flow between fractures and the matrix, and between the matrix and fractures and the exterior boundaries. Synthetic fracture networks are created using planar fractures of finite areal extent embedded within a three dimensional rock matrix for the purpose of performing sensitivity studies of network hydraulic conductivity with respect to geometric parameters, such as fracture orientation and density. Results of the sensitivity studies show that: (1) The global hydraulic conductivity is linearly dependent on the product of fracture transmissivity and density for fractures of which fully penetrate the rock volume; (2) The effect of correlation between fracture length and transmissivity is to increase the global hydraulic conductivity; and (3) Results using a three dimensional coupled fracture— matrix flow regime compare favorably with analytic results. Flow through variably saturated fracture networks is modeled by assuming a constant capillary head within individual fractures. A free surface is found using an iterative procedure which locates nodal points at the intersection of constant total head and pressure head contours. The simulated free surface compares favorably with an approximate analytic solution and with laboratory results. Simulations indicate the presence of zones of water under both positive and negative pressure, as well as regions of air—filled voids. Travel times and breakthrough curves are determined by integrating the inverse velocity over a streamline, and then summing over all streamlines. For the fracture network examined, travel times decrease with decreasing fracture saturation. The effects of retardation and matrix diffusion are also examined.

An analysis was performed of a Texas gulf coast hazardous waste injection well disposal system. The system was complicated by the presence of a fault which transected the injection interval. The existence of the fault presented the potential for enhanced vertical migration of the injected solutes via a tortuous path of interconnected, highly permeable sand units. Evaluation of this potential necessitated a fully three dimensional model which incorporated the arrangement of the alternating shales and sands and their associated discontinuities. Computer run time and memory limitations compelled a dissection of the problem into components, as well as the utilization of a specific mixture of conservative and realistic assumptions. The analysis indicated that within 10,000 years, the waste would advance vertically no further than one hundred feet into the overlying stratigraphy, and laterally no further than 24,000 feet from the point of injection.

Aromatic hydrocarbons are a prevalent constituent of crude oil. The refined products of crude oil such as petroleum and diesel can find their way into groundwater though oil-spillages and are also present in the oil and gas industry’s produced water. These aromatics are biorecalcitrant, however upon ingestion with water, may be metabolised to toxic intermediates that are carcinogenic or mutagenic in nature. Although some treatment technologies are available most of these are under development and are yet to be proven in the field. This illustrates the need for novel, economical and environmentally friendly technologies to be developed with a view to remediating aqueous systems that have been polluted with aromatics hydrocarbons. The supramolecular cyclodextrin molecule, with its hydrophobic interior and hydrophobic exterior seems to be an excellent molecule for the trapping of the pollutant molecules, however the inclusion complexes with this cyclic sugar are water-soluble therefore there is a need for the cyclodextrin to be rendered waterinsoluble. A study of the aqueous solubilities of some aromatic hydrocarbons that may be present in crude oil has been carried out and shows that the majority of these molecules have a degree of water solubility that may increase upon environmental weathering. The successful reaction between a solid-phase resin and the β-cyclodextrin molecule has been achieved, with the total dryness of the system being required including Soxhlet extraction of the resin with anhydrous acetone before the reaction. The reaction between β-cyclodextrin and a range of isocyanates proved unsuccessful, but a range of symmetrical aryl ureas were synthesised from their isocyanates with the influence that different activating or deactivating groups on the ring have on the propensity to form the ureas being shown. The successful alkylation between β-cyclodextrin and a series of haloalkanes has shown the effect of increasing chain length on the degree of alkylation. This reaction involved the deprotonation of the cyclodextrin by sodium hydride in anhydrous dimethyl sulphoxide followed by reaction with the alkyl iodide. Increasing the equivalents of hydride or iodide, or the reaction time did not have a noticeable effect on the degree of reaction indicating that steric constraints were limiting the degree of reaction. Testing several of these alkyl iodides gave an indication as to their tendency to uptake and remove several model pollutants that had been dissolved in water with the propylated β-cyclodextrin displaying potential for the remediation of aqueous systems that had been polluted. Several of these results were very promising leading to the conclusion that further derivatives of these alkylated sugars may be even more suitable for future research into the remediation of organically polluted aqueous systems.

Several biomarkers (cell viability and phagocytosis) based on earthworm (Lumbricus terrestris) immune cells (coelomocytes), together with whole-worm mortality (LC/LD50's), were used to assess a bioremediation attempt to reduce pentachlorophenol (PCP) toxicity in a former wood processing hazardous waste site (HWS).