Spelling suggestions: "subject:"heat exchanger -- ingesting"" "subject:"heat exchanger -- andtesting""
1 |
An investigation of the performance of cross-flow heat exchangers used in air conditioningKane, Eneas Dillon January 2011 (has links)
Typescript, etc. / Digitized by Kansas State University Libraries
|
2 |
Single phase heat transfer enhancement by doubly augmented tubesKaushik, Nanda. January 1985 (has links)
Call number: LD2668 .T4 1985 K38 / Master of Science
|
3 |
Measurement of Finned-Tube Heat Exchanger PerformanceTaylor, Creed 01 December 2004 (has links)
Finned-tube heat exchangers are predominantly used in space conditioning systems, as well as other applications requiring heat exchange between two fluids. One important widespread use is in residential air conditioning systems. These residential cooling systems influence the peak demand on the U.S. national electrical system, which occurs on the hot summer afternoons, and thereby sets the requirement for the expensive infrastructure requirement of the nations power plant and electrical distribution system. In addition to this peak demand, these residential air conditioners are major energy users that dominate residential electrical costs and environmental impact.
The design of finned-tube heat exchangers requires the selection of over a dozen design parameters by the designer. The refrigerant side flow and heat transfer characteristics inside the tubes have been thoroughly studied. However, the air side flow around the tube bundle and through the fin gaps is much more complex and depends on over a dozen design parameters. Therefore, experimental measurement of the air side performance is needed.
First this study built an experimental system and developed methodology for measuring the air side heat transfer and pressure drop characteristics of fin tube heat exchangers. This capability was then used to continue the goal of expanding and clarifying the present knowledge and understanding of air side performance to enable the air conditioner system designer in verifying an optimum fin tube condenser design.
In this study eight fin tube heat exchangers were tested over an air flow face velocity range of 5 ?? ft/s (675-1600cfm). The raw data were reduced to the desired heat transfer and friction data, j and f factors. This reduced heat transfer and friction data was plotted versus Reynolds number and compared. The effect of fin spacing, the number of rows and fin enhancement were all investigated. The heat transfer and friction data were also plotted and compared with various correlations available from open literature. The overall accuracy of each correlation to predict experimental data was calculated. Correlations by C.C. Wang (1998b, 1999) showed the best agreement with the data. Wangs correlations (1998b, 1999) were modified to fit the current studys data.
|
4 |
The geometric characterization and thermal performance of a microchannel heat exchanger for diesel engine waste heat recoveryYih, James S. 29 November 2011 (has links)
Rising energy demands and the continual push to find more energy efficient technologies have been the impetus for the investigation of waste heat recovery techniques. Diesel engine exhaust heat utilization has the potential to significantly reduce the consumption of fossil fuels and reduce the release of greenhouse gases, because diesel engines are ubiquitous in industry and transportation. The exhaust energy can used to provide refrigeration by implementing an organic Rankine cycle coupled with a vapor-compression cycle. A critical component in this system, and in any waste heat recovery system, is the heat exchanger that extracts the heat from the exhaust.
In this study, a cross-flow microchannel heat exchanger was geometrically examined and thermally tested under laboratory conditions. The heat exchanger, referred to as the Heat Recovery Unit (HRU), was designed to transfer diesel exhaust energy to a heat transfer oil. Two methods were developed to measure the geometry of the microchannels. The first was based on image processing of microscope photographs, and the second involved an analysis of profilometer measurements. Both methods revealed that the exhaust channels (air channels) were, on average, smaller in cross-sectional area by 11% when compared to the design. The
cross-sectional area of the oil channels were 8% smaller than their design. The hydraulic diameters for both channel geometries were close to their design.
Hot air was used to simulate diesel engine exhaust. Thermal testing of the heat exchanger included measurements of heat transfer, effectiveness, air pressure drop, and oil pressure drop. The experimental results for the heat transfer and effectiveness agreed well with the model predictions. However, the measured air pressure drop and oil pressure drop were significantly higher than the model. The discrepancy was attributed to the model's ideal representation of the channel areas. Additionally, since the model did not account for the complex flow path of the oil stream, the measured oil pressure drop was much higher than the predicted pressure drop. The highest duty of the Heat Recovery Unit observed during the experimental tests was 12.3 kW and the highest effectiveness was 97.8%.
To examine the flow distribution through the air channels, velocity measurements were collected at the outlet of the Heat Recovery Unit using a hot film anemometer. For unheated air flow, the profile measurements indicated that there was flow maldistribution. A temperature profile was measured and analyzed for a thermally loaded condition. / Graduation date: 2012
|
Page generated in 0.2153 seconds