Master of Science / Department of Physics / Robert Szoszkiewicz / Nanoscale modifications of polymer surfaces by scratching them with sharp tips with curvature radii of tens of nanometers and at variable temperatures are expected to provide wealth of information characterizing wear response of these polymers. Such studies are important in the light of understanding the nanoscale behavior of matter for future applications in advanced polymer coatings. This thesis describes how Atomic Force Microscopy (AFM) and hot-tip AFM (HT-AFM) methods were used to characterize thermal and mechanical properties of a 30 nm thick film of poly(styrene-block-ethylene oxide), PS-b-PEO, and modify its lamellar surface patterns. Additionally, it is revealed how contact AFM and HT-AFM methods can efficiently characterize the wear response of two popular polymer surfaces, poly(methyl methacrylate), PMMA, and polystyrene, PS. The AFM and HT-AFM studies on PS-b-PEO copolymer were aimed at producing spatial alignment of respective PS and PEO parts. Instead, however, surface ripples were obtained. These measurements are explained using mode I crack propagation model and stick-and-slip behavior of an AFM tip. In addition, HT-AFM studies allowed extraction of several thermo-physical properties of a PS-b-PEO film at local volumes containing about 30 attograms of a polymer. These thermo-physical quantities are: PEO melting enthalpy of, 111 ± 88 J g[superscript]-1, PS-b-PEO local specific heat of 3.6 ± 2.7 J g[superscript]-1K[superscript]-1, and molecular free energy of Helmholtz of 10[superscript]-20 J nm[superscript]-2 for the PEO within PS-b-PEO. Utilizing a spiral scan pattern at constant angular speed and at various temperatures at the AFM tip-polymer interfaces, the wear response of PS and PMMA polymers was characterized. Cross-sections along the obtained spiral wear patterns provided plots of polymer corrugation as a function of scanning speed. From these studies it was found that the corrugation of the modified polymer surface decays exponentially with linear velocity of the scanning tip.

Hot microelectrodes are very small electrodes (usually 1 100 µm in diameter), which have a surface temperature much higher than the temperature in the bulk solution. In this work, the heating is achieved by applying an alternating potential of very high frequency (100 MHz 2 GHz) and of high amplitude (up to 2.8 Vrms) to the microelectrode. As a result, very fast (on the order of milliseconds) changes in the temperature of the electrolyte solution surrounding the electrode can be achieved. Due to the size of the heated microelectrodes, the hot zone in solution is small. Therefore, the solution can be easily overheated and temperatures above the boiling point can be reached.<p> The purpose of this research was to investigate and understand the phenomena occurring at ac polarized microelectrodes and to propose new applications of these electrodes. Using both steady-state and fast-scan (10 V/s) cyclic voltammetry measurements, mass transport of redox species has been studied at ac heated microelectrodes. It has been established that the convection at hot-disk microelectrodes is driven primarily by the electrothermal flow of an electrolyte solution. In addition, other effects such as ac dielectrophoresis and Soret (nonisothermal) diffusion are also observed. Numerical simulations have been employed to predict the distribution of temperature in the hot zone, the direction and magnitude of the electrothermal force and the solution flow rate, as well as the voltammetric response of hot-disk microelectrodes. The results of the simulations agree well with the experimental observations. Theoretical findings of this PhD work are very important for the understanding of the fundamentals of high temperature electrochemistry, particularly mass transport. The proposed explanation of the convection mechanism is most likely applicable not only to ac polarized microelectrodes, but also to the microwave heated microelectrodes, since the only difference between these two heating methods is in the way of delivering electrical energy (wired vs. wireless). The results of the studies of Soret diffusion indicate that it contributes significantly to mass transfer of redox species at hot microelectrodes. Taking into account that the magnitude of the Soret effect has been considered negligible by other electrochemists, the results obtained in this work prove the opposite and show that Soret diffusion affects both the faradaic current and the half-wave potential of the redox reaction. Therefore, the Soret effect can not be ignored if working with hot microelectrodes.<p> Hot microelectrodes can have a number of interesting applications. The results of the initial investigations indicate that these electrodes can be successfully used in the arrangement for Scanning Electrochemical Microscopy (such a novel technique is termed Hot-Tip SECM). In addition, the observed dielectrophoretic and electrothermal convection effects can enhance the performance of the electrochemical sensors based on hot microelectrodes. This can lead to the improvement of the detection limits of many biologically important analytes, such as proteins, bacteria and viruses.

Hot microelectrodes are very small electrodes (usually 1 100 µm in diameter), which have a surface temperature much higher than the temperature in the bulk solution. In this work, the heating is achieved by applying an alternating potential of very high frequency (100 MHz 2 GHz) and of high amplitude (up to 2.8 Vrms) to the microelectrode. As a result, very fast (on the order of milliseconds) changes in the temperature of the electrolyte solution surrounding the electrode can be achieved. Due to the size of the heated microelectrodes, the hot zone in solution is small. Therefore, the solution can be easily overheated and temperatures above the boiling point can be reached.<p> The purpose of this research was to investigate and understand the phenomena occurring at ac polarized microelectrodes and to propose new applications of these electrodes. Using both steady-state and fast-scan (10 V/s) cyclic voltammetry measurements, mass transport of redox species has been studied at ac heated microelectrodes. It has been established that the convection at hot-disk microelectrodes is driven primarily by the electrothermal flow of an electrolyte solution. In addition, other effects such as ac dielectrophoresis and Soret (nonisothermal) diffusion are also observed. Numerical simulations have been employed to predict the distribution of temperature in the hot zone, the direction and magnitude of the electrothermal force and the solution flow rate, as well as the voltammetric response of hot-disk microelectrodes. The results of the simulations agree well with the experimental observations. Theoretical findings of this PhD work are very important for the understanding of the fundamentals of high temperature electrochemistry, particularly mass transport. The proposed explanation of the convection mechanism is most likely applicable not only to ac polarized microelectrodes, but also to the microwave heated microelectrodes, since the only difference between these two heating methods is in the way of delivering electrical energy (wired vs. wireless). The results of the studies of Soret diffusion indicate that it contributes significantly to mass transfer of redox species at hot microelectrodes. Taking into account that the magnitude of the Soret effect has been considered negligible by other electrochemists, the results obtained in this work prove the opposite and show that Soret diffusion affects both the faradaic current and the half-wave potential of the redox reaction. Therefore, the Soret effect can not be ignored if working with hot microelectrodes.<p> Hot microelectrodes can have a number of interesting applications. The results of the initial investigations indicate that these electrodes can be successfully used in the arrangement for Scanning Electrochemical Microscopy (such a novel technique is termed Hot-Tip SECM). In addition, the observed dielectrophoretic and electrothermal convection effects can enhance the performance of the electrochemical sensors based on hot microelectrodes. This can lead to the improvement of the detection limits of many biologically important analytes, such as proteins, bacteria and viruses.