Thesis (M.S.)--Missouri University of Science and Technology, 2008. / Vita. The entire thesis text is included in file. Title from title screen of thesis/dissertation PDF file (viewed April 25, 2008) Includes bibliographical references (p. 57).

Thesis (Ph. D.)--University of Missouri-Columbia, 1996. / Typescript. Vita. Includes bibliographical references (leaves 254-260). Also available on the Internet.

Thesis (Ph. D.)--University of Missouri-Columbia, 1996. / Typescript. Vita. Includes bibliographical references (leaves 254-260). Also available on the Internet.

M.S.

A cantilever beam type, capacitive sensing, skin friction gage has been developed. A prototype along with supporting electronics has been constructed. The cantilever beam gage is a change of area variable capacitive transducer. It is designed to measure the wall shear stress in a short duration, supersonic flow. The supporting electronics consists of an electrical oscillator for frequency modulation, and a frequency demodulator. The change in capacitance due to the shear stress in the flow modulates the output signal of the oscillator, which is then demodulated to extract a voltage signal which corresponds to the change in capacitance of the gage. The gage and the electronics were constructed from simple, inexpensive components for the purpose of proving the concept of a capacitive sensing transducer. static calibrations have been completed and statistical analysis has been done to test the performance of the gage. A 0.12 mV response due to the expected 98.1 g m/s2 force input of the skin friction of the Mach 2.9 design flow, over the 0.49 in2 (316.1 mm) area of the gage's sensing head, was measured as the average output of the skin friction gage instrumented with stainless steel strips. / Master of Science

This work uses computational fluid dynamics to study the flowfield around a hypersonic missile with two lateral jets to provide control in place of control surfaces. The jets exhaust an H2-O2 mixture at Mach number of 2.9 with a jet pressure ratio of roughly 10,500. The jets are staggered axially and circumferentially in such a way to produce pitch and yaw. The flowfield of such a jet configuration is characterized at several angles of attack and the corresponding force coefficients and amplification factors are provided. The freestream air and H2-O2 plume is treated as inert for the majority of the calculations. Special cases are treated with finite rate chemical kinetics and compared to the inert flowfield to ascertain the effects that chemical reactions have on the force coefficients. It was found that the flowfield was only slightly altered from the familiar one jet flowfield when the second jet is active. The flow topology and vortex structures tend to shift towards the second jet but the overall structure remains the same. The normal force amplification factors are close to unity over the range of angle of attack due to the thrust being so high with the two jet configuration having a lower amplification factor compared to firing a single jet. Treating the flowfield as chemically reacting did not affect the force values much: the difference being 0.3% for an angle of attack of 0°. / Includes bibliography. / Dissertation (Ph.D.)--Florida Atlantic University, 2017. / FAU Electronic Theses and Dissertations Collection

With the age of hypersonic flight imminent just beyond the horizon, researchers are working hard at designing work-arounds for all the major problems as well as the minor quirks associated with it. One such issue, seemingly innocuous but one that could be potentially deadly, is the problem of interference heating due to surface protuberances. Although an ideal design of the external surfaces of a high-speed aircraft dictates complete smoothness to reduce drag, this is not always possible in reality. Control surfaces, sheet joints, cable protection pads etc. generate surface discontinuities of varying geometries, in the form of both protrusions as well as cavities. These discontinuities are most often small in dimension, comparable to the local boundary layer thickness at that location. Such protuberances always experience high rates of heat transfer, and therefore should be appropriately shielded. However, thermal shielding of the protrusions alone is not a full solution to the problem at hand. The interference caused to the boundary layer by the flow causes the generation of local hot spots in the vicinity of the protuberances, which should be properly mapped and adequately addressed. The work presented in this thesis aims at locating and measuring the heat flux values at these hot spots near the protrusions, and possibly formulating empirical correlations to predict the hot spot heat flux for a given set of flow conditions and protrusion geometry. Experimental investigations were conducted on a flat plate model and a cone model, with interchangeable sharp and blunt nose tips, with attached 3D protuberances. Platinum thin-film sensors were placed around the protrusion so that the heat fluxes could be measured in its vicinity and the hottest spot located. These experiments were carried out at five different hypersonic free stream flow conditions generated using two shock tunnels, one of the conventional type, and the other of the free-piston driven type. The geometry of the protrusions, i.e., the height and the deflection angle, was also parametrically varied to study its effect on the hot spot heat flux. The results thus obtained for the flat plate case were compared to existing correlations in the open literature from a similar previous study at a much higher Reynolds number range. Since a mismatch was observed between the results of the current experiments and the existing correlations, a new empirical correlation has been developed to predict the hot spot heat flux, that is valid within the range of flow conditions studied here. A similar attempt was made for the case of the cone model, for which no previous correlations exist in the open literature. However, a global correlation covering the entire range of flow conditions used here could not be formed. A correlation that is valid for just one out of the five flow conditions used here is presented for the cones with sharp and blunt nose tips separately. Schlieren flow visualization was carried out to obtain a better understanding of the shock structures near the protuberances on both models. For most cases, where the protrusion height and deflection angle were large enough to cause flow separation immediately upstream of the protuberance, a separation shock was manifested which deflected some part of the boundary layer above the protuberance, while the rest of the fluid in the boundary layer entered a recirculating region in the separated zone before escaping to the side. Some preliminary computational analysis was conducted which confirmed this qualitatively. However, the quantitative match of surface heat flux between the simulations and experiments were not encouraging. Schlieren visualization revealed that for the flat plate case, the foot of the separation shock was located at a distance of 10.5 to 12 times the protrusion height ahead of it, whereas in the case of the sharp cone, it was at a distance of 9 to 10.5 times the protrusion height. The unsteady nature of the separation shock was also captured and addressed. Some preliminary experiments on boundary layer tripping were also conducted, the results of which have been presented here. From this analysis, it has become evident that a single global correlation cannot be formed which could be used for a wide range of flow conditions to predict the hot spot heat flux in interference interactions. The entire range of conditions that may be encountered during hypersonic flight has to be broken down into sections, and the interference heating pattern should be studied in each of these sections individually. By doing so, a series of different correlations can be formed at the varying flow conditions which will then be available for high-speed aircraft designers.

One of the current goals of research in hypersonic, airbreathing propulsion is access to higher Mach numbers. A strong driver of this goal is the desire to integrate a scramjet engine into a transatmospheric vehicle airframe in order to improve performance to low Earth orbit (LEO) or the performance of a semi-global transport. An engine concept designed to access hypervelocity speeds in excess of Mach 10 is the shock-induced combustion ramjet (i.e. shcramjet). This dissertation presents numerical studies simulating the physics of a shcramjet vehicle traveling at hypervelocity speeds with the goal of understanding the physics of fuel injection, wall autoignition mitigation, and combustion instability in this flow regime. This research presents several unique contributions to the literature. First, different classes of injection are compared at the same flow conditions to evaluate their suitability for forebody injection. A novel comparison methodology is presented that allows for a technically defensible means of identifying outperforming concepts. Second, potential wall cooling schemes are identified and simulated in a parametric manner in order to identify promising autoignition mitigation methods. Finally, the presence of instabilities in the shock-induced combustion zone of the flowpath are assessed and the analysis of fundamental physics of blunt-body premixed, shock-induced combustion is accelerated through the reformulation of the Navier Stokes equations into a rapid analysis framework. The usefulness of such a framework for conducting parametric studies is demonstrated.