The structural properties of the group III-nitrides including AlN, Ga1-xMnxN, GaN:Cu, and InN were investigated by Raman spectroscopy. Absorption and photoluminescence spectroscopy were utilized to study the optical properties in these materials. The analysis of physical vapor transport grown AlN single crystals showed that oxygen, carbon, silicon, and boron are the major impurities in the bulk AlN. The Raman analysis revealed high crystalline quality and well oriented AlN single crystals. The absorption coefficient of AlN single crystals were assessed in the spectral range from deep UV to the FIR. The absorption and photoluminescence analysis indicate that, in addition to oxygen, carbon, boron, and silicon, contribute to the optical properties of bulk AlN crystals. In situ Cu-doped GaN epilayers with Cu concentrations in the range of 2x10^16 cm-3 - 5x1017 cm-3, grown on sapphire substrate by metal organic chemical vapor deposition, were investigated by Raman and PL spectroscopy. The Raman study revealed high crystalline GaN:Cu layers with minimal damage to the hexagonal lattice structure due to the Cu incorporation. A strong Cu related emission band at 2.4 eV was assigned to Cu induced optical transitions between deep Cu states and shallow residual donor states. Compensation of Cu states by residual donors and poor activation probability of deep Cu states are responsible for semi-insulating electrical conductivity. Ferromagnetic Ga1-xMnxN epilayers, grown by MOCVD with Mn concentration from x = 0 to x = 1.5, were optically investigated by Raman, PL, and transmission spectroscopy. The Raman studies revealed Mn-related Raman peaks at 300 cm-1, 609 cm-1, and 669 cm-1. Mn-related absorption and emission bands in Ga1-xMnxN were observed at 1.5 eV and 3.0 eV, respectively. The structural properties of InN layers, grown by high pressure-CVD with different free carrier concentrations, were analyzed by Raman spectroscopy. The Raman results show that the InN layers have high crystalline quality. The free carriers in layers were calculated by using the Lindhard-Mermin dielectric function taking into account finite wave vectors for various scattering processes including forbidden Frohlich, deformational potential associated with allowed electro-optic, and charge density fluctuation, mechanisms. The free carrier concentrations in the layers are below 1x10^20 cm-3.

No description available.

Through the history of mankind, novel materials have played a key role in techno- logical progress. As we approach the limits of scaling it becomes difficult to squeeze out any more extensions to Moore’s law by just reducing device feature sizes. It is important to look for an alternate semiconductor to silicon in order to continue making the progress predicted by Moore’s law. Among the various semiconductor options being explored world-wide, the III-nitride semiconductor material system has certain unique characteristics that make it one of the leading contenders. We explore the III-nitride semiconductor material system for the unique advantages that it offers over the other alternatives available to us. This thesis studies the device applications of epitaxial III-nitride films and nanos- tructures grown using plasma assisted molecular beam epitaxy (PAMBE) The material characterisation of the PAMBE grown epitaxial III-nitrides was car- ried out using techniques like high resolution X-ray diffraction (HR-XRD), field emis- sion scanning electron microscopy (FESEM), room temperature photoluminescence (PL) and transmission electron microscopy (TEM). The epitaxial III-nitrides were then further processed to fabricate devices like Schottky diodes, photodetectors and surface acoustic wave (SAW) devices. The electrical charcterisation of the fabricated devices was carried out using techniques like Hall measurement, IV and CV measure- ments on a DC probe station and S-parameter measurements on a vector network analyser connected to an RF probe station. We begin our work on Schottky diodes by explaining the motivation for adding an interfacial layer in a metal-semiconductor Schottky contact and how high-k di- electrics like HfO2 have been relatively unexplored in this application. We report the work carried out on the Pt/n-GaN metal-semiconductor (MS) Schottky and the Pt/HfO2/n-GaN metal-insulator-semiconductor (MIS) Schottky diode. We report an improvement in the diode parameters like barrier height (0.52 eV to 0.63 eV), ideality factor (2.1 to 1.3) and rectification ratio (35.9 to 98.9 @2V bias) after the introduction of 5 nm of HfO2 as the interfacial layer. Temperature dependent I-V measurements were done to gain a further understanding of the interface. We observe that the barrier height and ideality factor exhibit a temperature dependence. This was attributed to inhomogeneities at the interface and by assuming a Gaussian distribution of barrier heights. UV and IR photodetectors using III-nitrides are then studied. Our work on UV photodetectors describes the growth of epitaxial GaN films. Au nanoparticles were fabricated on these films using thermal evaporation and annealing. Al nanostruc- tures were fabricated using nanosphere lithography. Plasmonic enhancement using these metallic nanostructures was explored by fabricating metal-semiconductor-metal (MSM) photodetectors. We observed plasmonic enhancement of photocurrent in both cases. To obtain greater improvement, we etched down on the GaN film using reac tive ion etching (RIE). This resulted in further increase in photocurrent along with a reduction in dark current which was attributed to creation of new trap states. IR photodetectors studied in this thesis are InN quantum dots whose density can be controlled by varying the indium flux during growth. We observe that increase in InN quantum dot density results in increase in photocurrent and decrease in dark current in the fabricated IR photodetectors. We then explore the advantages that InGaN offers as a material that supports surface acoustic waves and fabricate InGaN based surface acoustic wave devices. We describe the growth of epitaxial In0.23 Ga0.77 N films on GaN template using molecular beam epitaxy. Material characterisation was carried out using HR-XRD, FESEM, PL and TEM. The composition was determined from HR-XRD and PL measurements and both results matched each other. This was followed by the fabrication of interdigited electrodes with finger spacing of 10 µm. S-parameter results showed a transmission peak at 104 MHz with an insertion loss of 19 dB. To the best of our knowledge, this is the first demonstration of an InGaN based SAW device. In summary, this thesis demonstrates the practical advantages of epitaxially grown film and nanostructured III-nitride materials such as GaN, InN and InGaN using plasma assisted molecular beam epitaxy for Schottky diodes, UV and IR photodetec- tors and surface acoustic wave devices.

Group III-nitride semiconductors are well suited for the fabrication of devices including visible-ultraviolet light emitting diodes, high-temperature and high-frequency devices. The wurtzite III-nitride based heterostructures grown along polar c-direction have large internal electric fields due to discontinuities in spontaneous and piezoelectric polarizations. For optoelectronic devices, such as light-emitting diodes and laser diodes, the internal electric field is deleterious as it causes a spatial separation of electron and hole wave functions in the quantum wells, which decreases emission efficiency. Growth of GaN-based heterostructures in alternative orientations, which have reduced (semipolar) or no polarization (nonpolar) in the growth direction, has been a major area of research in the last few years. The correlation between structural, optical and transport properties of semipolar and nonpolar III-nitride would be extremely useful. The thesis focuses on the growth and characterizations of semipolar and nonpolar III-nitride heterostructures by plasma-assisted molecular beam epitaxy. Chapter 1 provides a brief introduction to the III-nitride semiconductors. The importance of semipolar and nonpolar III-nitride heterostructures over conventional polar heterostructures has been discussed. Chapter 2 deals with the descriptions of molecular beam epitaxy system and working principles of different characterization tools used in the present work. Chapter 3 addresses the molecular beam epitaxial growth of nonpolar (1 1 -2 0) and semipolar (1 1 -2 2) GaN on sapphire substrates. An in-plane orientation relationship is found to be [0 0 0 1] GaN || [-1 1 0 1] sapphire and [-1 1 0 0] GaN || [1 1 -2 0] sapphire for nonpolar GaN on r-sapphire substrates. Effect of growth temperature on structural, morphological and optical properties of nonpolar GaN has been studied. The growth temperature plays a major role in controlling crystal quality, morphology and emission properties of nonpolar a-plane GaN. The a-plane GaN shows crystalline anisotropy nature and it has reduced with increase in the growth temperature. The surface roughness was found to decrease with increase in growth temperature and film grown at 760°C shows reasonably smooth surface with roughness 3.05 nm. Room temperature photoluminescence spectra show near band emission peak at 3.434 -3.442 eV. The film grown at 800 ºC shows broad yellow luminescence peak at 2.2 eV. Low temperature photoluminescence spectra show near band emission at 3.483 eV along with defect related emissions. Raman spectra exhibit blue shift due to compressive strain in the film. An in-plane orientation relationship is found to be [1 -1 00] GaN || [1 2-1 0] sapphire and [-1 -1 2 3] GaN || [0 0 0 1] sapphire for semipolar GaN on m-plane sapphire substrates. The surface morphology of semipolar GaN film is found to be reasonably smooth with pits on the surface. Room temperature photoluminescence shows the near band emission (NBE) at 3.432 eV, which is slightly blue shifted compared to the bulk GaN. The Raman E2 (high) peak position observed at 569.1 cm1. Chapter 4 deals with the fabrication and characterizations of Au/nonpolar and Au/semipolar GaN schottky diodes. The temperature-dependent current–voltage measurements have been used to determine the current mechanisms in Schottky diodes fabricated on nonpolar a-plane GaN and semipolar GaN epilayers. The barrier height (φb) and ideally factor (η) estimated from the thermionic emission model are found to be temperature dependent in nature indicate the deviations from the thermionic emission (TE) transport mechanism. Low temperature I-V characteristics of Au/ GaN Schottky diode show temperature independent tunnelling parameter. Barrier heights calculated from XPS are found to be 0.96 eV and 1.13 eV for Au/nonpolar GaN and Au/semipolar GaN respectively. Chapter 5 demonstrates the growth of InN on r-sapphire substrates with and without GaN buffer layer. InN film and nanostructures are grown on r-sapphire without GaN buffer layer and they are highly oriented along (0002) direction. The electron microscopy study confirms the nanostructures are vertically aligned and highly oriented along the (0001) direction. The Raman studies of InN nanostructures show the SO modes along with the other possible Raman modes. The band gap of InN nanostructures is found to be 0.82 eV. InN grown with a-plane GaN buffer shows nonpolar orientated growth. Growth temperature dependent studies of nonpolar a-plane InN epilayers are carried out. The valence band offset value is calculated to be 1.31 eV for nonpolar a-plane InN/GaN heterojunctions. The heterojunctions form in the type-I straddling configuration with a conduction band offsets of 1.41 eV. Chapter 6 deals with the temperature dependent I-V characteristics of the nonpolar a-plane (1 1 -2 0) InN/GaN heterostructures. The measured values of barrier height and ideality factor from the TE model show the temperature dependent variation. The double Gaussian distribution has mean barrier height values ( ϕb ) of 1.17 and 0.69 eV with standard deviation (σs ) of 0.17 and 0.098 V, respectively. The modified Richardson plot ln (Is/T2)-q2σ2/2k2T2 ) versus q/kT in the temperature range of 350 – 500 K, yielded the Richardson constant of 19.5 A/cm2 K2 which is very close to the theoretical value of 24 A/cm2 K2 for n-type GaN. The tunneling parameters E0 found to be temperature independent at low temperature range (150 –300 K). Chapter 7 concludes with the summary of present investigations and the scope for future work.

Group III-nitride semiconductors have received much research attention and witnessed a significant development due to their ample applications in solid-state lighting and high-power/high-frequency electronics. Numerous growth methods were explored to achieve device quality epitaxial III-nitride semiconductors. Among the growth methods for III-nitride semiconductors, molecular beam epitaxy provides advantages such as formation of abrupt interfaces and in-situ monitoring of growth. The present research work focuses on the growth and characterizations of III-nitride based epitaxial films, nanostructures and heterostructures on c-sapphire substrate using plasma-assisted molecular beam epitaxy system. The correlation between structural, optical and electrical properties of III-nitride semiconductors would be extremely useful. The interfaces of the metal/semiconductor and semiconductor heterostructures are very important in the performance of semiconductor devices. In this regard, the electrical transport studies of metal/semiconductor and semiconductor heterostructures have been carried out. Besides, studies involved with the defect induced room temperature ferromagnetism of GaN films and InN nano-structures have also been carried out. The thesis is organized in eight different chapters and a brief overview of each chapter is given below. Chapter 1 provides a brief introduction on physical properties of group III-nitride semiconductors. It also describes the importance of III-nitride heterostructures in the operation of optoelectronic devices. In addition, it also includes the current strategy of the emergence of room temperature ferromagnetism in III-nitride semiconductors. Chapter 2 deals with the basic working principles of molecular beam epitaxy system and different characterization tools employed in the present work. Chapter 3 describes the growth of GaN films on c-sapphire by plasma-assisted molecular beam epitaxy. The effects of N/Ga flux ratio on structural, morphological and optical properties have been studied. The flux ratio plays a major role in controlling crystal quality, morphology and emission properties of GaN films. The dislocation density is found to increase with increase in N/Ga flux ratio. The surface morphologies of the films as seen by scanning electron microscopy show pits on the surface and found that the pit density on the surface increases with flux ratio. The room temperature photoluminescence study reveals the shift in band-edge emission towards the lower energy with increase in N/Ga flux ratio. This is believed to arise from the reduction in compressive stress in the GaN films as it is evidenced by room temperature Raman study. The transport studies on the Pt/GaN Schottky diodes showed a significant increase in leakage current with an increase in N/Ga ratio and is found to be caused by the increase in dislocation density in the GaN films. Chapter 4 deals with the fabrication and characterization of Au/GaN Schottky diodes. The temperature dependent current–voltage measurements have been used to determine the current transport mechanism in Schottky diodes. The barrier height (φb) and the ideality factor (η) are estimated from the thermionic emission model and are found to be temperature dependent in nature, indicating the existence of barrier height inhomogeneities at the Au/GaN interface. The conventional Richardson plot of ln(Is/T2) versus 1/kT gives Richardson constant value of 3.23×10-5 Acm-2 K-2, which is much lower than the known value of 26.4 Acm-2 K-2 for GaN. Such discrepancy of Richardson constant value was attributed to the existence of barrier height inhomogeneities at the Au/GaN interface. The modified Richardson plot of ln(Is/T2)-q2σs2/2k2T2 versus q/kT, by assuming a Gaussian distribution of barrier heights at the Au/GaN interface, provides the Schottky barrier height of 1.47 eV and Richardson constant value of 38.8 Acm-2 K-2 which is very close to the theatrical value of Richardson constant. The temperature dependence of barrier height is interpreted on the basis of existence of the Gaussian distribution of the barrier heights due to the barrier height inhomogeneities at the Au/GaN interface. Chapter 5 addresses on the influence of GaN underlayer thickness on structural, electrical and optical properties of InN thin films grown using plasma-assisted molecular beam epitaxy. The high resolution X-ray diffraction study reveals superior crystalline quality for the InN film grown on thicker GaN film. The electronic and optical properties seem to be greatly influenced by the structural quality of the films, as can be evidenced from Hall measurement and optical absorption spectroscopy. Also, we present the studies involving the dependence of structural, electrical and optical properties of InN films, grown on thicker GaN films, on growth temperature. The optical absorption edge of InN film is found to be strongly dependent on carrier concentration. Kane’s k.p model is used to describe the dependence of optical absorption edge on carrier concentration by considering the non-parabolic dispersion relation for carrier in the conduction band. Chapter 6 deals with the analysis of the temperature dependent current transport mechanisms in InN/GaN heterostructure based Schottky junctions. The barrier height (φb) and the ideality factor (η) of the InN/GaN Schottky junctions are found to be temperature dependent. The temperature dependence of the barrier height indicates that the Schottky barrier height is inhomogeneous in nature at the heterostructure interface. The higher value of the ideality factor and its temperature dependence suggest that the current transport is primarily dominated by thermionic field emission (TFE) other than thermionic emission (TE). The room temperature barrier height and the ideality factor obtained by TFE model are 1.43 eV and 1.21, respectively. Chapter 7 focuses on the defect induced room temperature ferromagnetism in Ga deficient GaN epitaxial films and InN nano-structures grown on c-sapphire substrate by using plasma-assisted molecular beam epitaxy. The observed yellow emission peak in room temperature photoluminescence spectra and the peak positioning at 300 cm-1 in Raman spectra confirms the existence of Ga vacancies in GaN films. The ferromagnetism in Ga deficient GaN films is believed to originate from the polarization of the unpaired 2p electrons of nitrogen surrounding the Ga vacancy. The InN nano-structures of different size are grown on sapphire substrate, the structural and magnetic properties are studied. The room temperature magnetization measurement of InN nano-structures exhibits the ferromagnetic behavior. The saturation magnetization is found to be strongly dependent on the size of the nano-structures. Finally, Chapter 8 gives the summary of the present work and the scope for future work in this area of research.