One of the major limitations in Fused Filament Fabrication (FFF), a form of additive manufacturing, is the lack of composites with superior mechanical properties. Traditionally, carbon and glass fibers are widely used to improve the physical properties of polymeric matrices. However, the blending methods lead to fiber breakage, preventing generation of long fiber reinforced filaments essential for printing load-bearing components. Our approach to improve tensile properties of the printed parts was to use in-situ composites to avoid fiber breakage during filament generation. In the filaments generated, we used thermotropic liquid crystalline polymers (TLCPs) to reinforce acrylonitrile butadiene styrene (ABS) and a high performance thermoplastic, polyphenylene sulfide (PPS). The TLCPs are composed of rod-like monomers which are highly aligned under extensional kinematics imparting excellent one-dimensional tensile properties. The tensile strength and modulus of the 40 wt.% TLCP/ABS filaments was improved by 7 and 20 times, respectively. On the other hand, the 67 wt.% TLCP/PPS filament tensile strength and modulus were improved by 2 and 12 times, respectively. The filaments were generated using dual extrusion technology to produce nearly continuously reinforced filaments and to avoid matrix degradation. Rheological tests were taken advantage of to determine the processing conditions. Dual extrusion technology allowed plasticating the matrix and the reinforcing polymer separately in different extruders. Then continuous streams of TLCP were injected below the TLCP melting temperature into the matrix polymer to avoid matrix degradation. The blend was then passed through a series of static mixers, subdividing the layers into finer streams, eventually leading to nearly continuous fibrils which were an order of magnitude lower in diameter than those of the carbon and glass fibers. The composite filaments were printed below the melting temperature of the TLCPs, and the conditions were determined to avoid the relaxation of the order in the TLCPs. On printing, a matrix-like printing performance was obtained, such that the printer was able to take sharp turns in comparison with the traditionally used fibers. Moreover, the filaments led to a significant improvement in the tensile properties on using in FFF and other conventional technologies such as injection and compression molding. / Doctor of Philosophy / In this work two thermoplastic matrices, acrylonitrile butadiene styrene (ABS) and polyphenylene sulfide (PPS), were reinforced with higher melting thermoplastics of superior properties called thermotropic liquid crystalline polymers (TLCPs). This was done so that the resulting filaments could be 3D-printed without melting the TLCPs. The goal of this work was to generate nearly continuous reinforcement in the filaments and to avoid matrix degradation, and, hence, a technology called dual extrusion technology was used for the filament generation. The temperatures required for filament generation were determined using rheology, which involves the study of flow behavior of complex fluids. Dual extrusion technology allows processing of the constituent polymers separately at different temperatures, followed by a continuous injection of multiple TLCP-streams into the matrix polymers. In addition, the use of static mixers (metallic components kept in the path of flow to striate incoming streams) leads to further divisions of the TLCP-streams which are eventually drawn by pulling to orient the TLCP phase. The resulting filaments exhibited specific properties (normalized tensile properties) higher than aluminum and contained fibers that were nearly continuous, highly oriented, and an order in magnitude lower in diameter than those of carbon and glass fiber, which are commonly used reinforcements. High alignment and lower fiber diameter are essential for printing smoother printed parts. The filaments were intended to be printed without melting the TLCPs. However, previous studies involving the use of TLCP reinforced composites in conventional technologies have reported the occurrence of orientation relaxation on postprocessing, which decreases their tensile v properties. Therefore, temperatures required for 3D printing were determined using compression molding to retain filament properties on printing to the maximum extent. On printing using an unmodified 3D printer, parts were printed by taking 180º turns during material deposition. Contrarily, the use of continuous carbon fibers required a modified 3D printer to allow impregnation during 3D printing. Moreover, the performance comparison showed that the continuous carbon fibers could not be deposited in tighter loops. The properties of the printed parts were higher than those obtained on using short fibers and approaching those of the continuous fiber composites.

Thermoplastic composites that have been reinforced by thermotropic liquid crystalline (TLCP) fibrils in the microscale and by nanoparticles in the nanoscale are defined as multi-scale wholly thermoplastic composites (WTCs). Multi-scale WTCs have been proposed as lightweight replacements with high performance for some traditional glass fiber (GF) and carbon fiber (CF) reinforced composites materials in various applications. TLCPs are known for performing mechanical properties similar to those of the lower end of CF but significantly better than those of GF. To enhance the mechanical properties of TLPC reinforced WTCs, carbon nanotubes (CNTs) are considered being used as a secondary enhancement in WTCs. CNTs have gathered significant interest in the last 30 years because of their high aspect ratio, high mechanical properties, and other high-performance properties. The focus of this work is on investigating the processing conditions of generating in situ injection-molded multi-scale WTCs, then extending the technology to dual-extrusion and fused filament fabrication (FFF) and obtain high-performance multi-scale WTC products. This dissertation initially focused on investigating the processing conditions, in particular mixing histories and processing temperature profiles, of generating in situ injection-molded multi-scale WTCs, which consist of a representative TLCP, scCO2 aided exfoliated CNTs, and the thermoplastic matrix polyamide 6 (PA 6). The supercooling behavior of the TLCP and thermal stability of PA 6 are studied by applying the rheological methods of small amplitude oscillatory shear (SAOS). Multiple mixing histories with CNTs and processing temperature profiles are analyzed based on the criterion of maximizing tensile properties of multi-scale WTCs and minimizing thermal degradation of the matrix. Under the optimum processing conditions, the in situ injection-molded multi-scale WTCs exhibit a 26% and 34% tensile modulus and strength enhancement, compared to the in situ injection-molded WTCs with no CNTs. Scanning electron micrograph (SEM) images were used to understand the enhancement. The second part of this work is to extend the scCO2 aided in situ multi-scale WTCs processing technology to dual-extrusion and FFF. Multi-scale WTC filaments, which consists of TLCP, CNTs, and polyamide copolymer (PAc), are generated by dual-extrusion, and 3D printed into rectangular specimens in FFF. The 1 wt% CNTs reinforced multi-scale WTC filaments generated by the means of dual-extrusion exhibit 225% and 80% improvement in tensile modulus and strength, respectively, compared to the WTC filaments with no CNTs. In FFF, 40 wt% TLCP/1 wt% CNT/PAc 3D printed specimens with filament laid in longitudinal direction exhibited excellent tensile modulus and strength of 38.92 GPa and 127.16 MPa, respectively. The well-dispersed exfoliated CNTs show high alignment with TLCP microfibrils in the multi-scale WTC filaments and their laid-down specimens, which causes the significant tensile modulus enhancement. Bridging elements are discovered between TLCP fibrils and PAc matrix to improve interfacial adhesion, which is attributed to the well-dispersed exfoliated CNTs. Finally, the significant improvements in tensile properties attributed to scCO2 aided exfoliated CNTs in WTCs are verified on the multi-scale WTCs based on polypropylene (PP). Moreover, additional tensile properties improvements for exfoliated CNTs reinforced multi-scale WTCs are obtained with the use of maleic anhydride grafted polypropylene (MAPP). With 1 wt% CNTs and 16 wt% MAPP dual reinforcement, 20 wt% TLCP reinforced WTCs based on polypropylene (PP) exhibit 265%, 274%, and 182% improvement in the tensile modulus of the filaments, laid up specimens in the concentric pattern and laid up specimens in ±45° rectilinear pattern, respectively. The dual reinforcement also improves the tensile strength of 20 wt% TLCP reinforced WTC filaments by up to 73%. The high alignment between TLCP fibrils and CNTs are confirmed in the multi-scale WTCs based on PP. Besides the bridging elements attributed to CNTs found in the second part of this work, SEM images show that CNTs are partially trapped in TLCP fibrils. / Doctor of Philosophy / Considering the need for environmentally friendly materials, novel thermoplastic composites with high mechanical performance, lightweight, and potentially high recyclability properties were generated in this work. Two types of thermoplastic matrices, polyamide (PA or nylon) and polypropylene (PP) were reinforced with carbon nanotubes (CNTs) and rigid chain polymers known as thermotropic liquid crystalline polymers (TLCPs). CNTs are known for their high mechanical properties and high aspect ratio, which are helpful to reinforce thermoplastic composite materials. During injection molding and the dual-extrusion processes, TLCPs deform into almost continuous microfibrils and reinforce the thermoplastic matrices. Instead of using traditional glass fibers or carbon fibers to reinforce thermoplastics, TLCP reinforced thermoplastic composites, which are defined as wholly thermoplastic composites (WTCs), can retain their mechanical properties during the recycling process such as in injection molding and have better performance during the lay-down process in fused filament fabrication. The goal of this work was to generate CNTs reinforced WTCs for use in injection molding and fused filament fabrication with high mechanical performance. In the injection molding process for generating CNTs reinforced WTC end-gated plaques, it was determined that the optimum thermal mixing histories for the CNTs could be identified by the inspections of the tensile property measurements and scanning electron microscopy (SEM). With the obtained optimum thermal mixing histories with CNTs, CNTs reinforced WTC filaments were generated by dual extrusion technology and used in fused filament fabrication. With 1 wt% addition of CNTs, the tensile properties of WTCs were significantly enhanced in both the filament materials and the laid-down parts. Especially, the CNT reinforced WTC filaments based on nylon matrices exhibited competitive tensile moduli to long carbon fiber reinforced nylon composite filaments, which was also competitive to the properties of aluminum alloys. In addition, the laid-down parts of CNTs reinforced WTC based on PP presented further tensile strength improvement due to the improved interfacial adhesion between the laid-down filaments and between layers, which was attributed to the addition of maleic anhydride grafted polypropylene.

Ceramic metal matrix composites (CMMCs) are materials generally created by mixing of hard ceramic particles in a metal matrix. They were expected to combine the ductility and toughness of the metal with the high strength and elastic modulus of the ceramic. MMCs have potential applications in automotive, aeronautical and aerospace industries. Hence, a simple and economical method for fabricating MMCs is an area of intense research. In MMCs, damage evolution starts preferentially at particle matrix interface or at particle clusters in the matrix. This is due to the different physical and mechanical properties of the particle and matrix. Higher local particle volume content leads to higher stress triaxiality making it a preferential site for damage nucleation. Problems with lowering of ductility, fatigue, fracture and impact resistance, agglomeration of ceramic phase and issues related to the predictability of properties of MMCs have been the major issues that have limited their use. In order to overcome some of these shortcomings, the use of nano particles has been attracting increasing attention. The reason is their capability in improving the mechanical and physical properties of traditional MMCs. The dispersion of a nanoscale ceramic phase is needed in order to overcome the problems related to fatigue, fracture toughness, and creep behaviour at high temperatures. However, manufacturing costs, preparation of nano composites and environmental concerns have to be addressed. Agglomeration of nano particles, when produced by the melt stir casting route, the primary route to produce MMCs, is a serious issue that limits the use of nano-particles to produce MMCs with good properties. To avoid agglomeration of the ceramic phase MMCs/nano MMCs have been produced through the powder metallurgy route. Agglomeration is avoided as this is a solid state process. Secondary processing, such as extrusion and rolling are often needed to fully consolidate materials produced in this manner. A high extrusion ratio is often required to get MMCs without porosity. A new method of making nano-ceramic MMC using a polymer derived ceramics (PDC) has been reported. A polymer derived ceramic is a material that converts itself into a ceramic when heated above a particular temperature. In the PDC method a polymer precursor is dispersed in the metal and then converted in-situ to a ceramic phase. A feature of this process is that all the constituents of the ceramic phase are built into the organic molecules of the precursor (e.g., polysilazanes contain silicon, carbon, and nitrogen); therefore, a reaction between the polymer and the host metal or air is not required to produce the ceramic phase. The polymer can be introduced through casting or powder metallurgy route. In the casting route, the polymer powder is directly added to molten metal and pyrolyzed in-situ to create castings of metal-matrix composites. These composites have shown better properties at elevated temperatures but the problem of agglomeration of particles due to Van der Waal's forces and porosity still remains. In the powder method, the organic precursor was milled with copper powder and then plasma sprayed to produce a metal matrix composite. It is reported that these composites retains its mechanical strength close to the melting point of the copper. However, getting a nano sized distribution is difficult through this route as the plasma spray route is a melting and solidification method. Solid state processing by powder metallurgy is possibly a better method to produce well dispersed nano-MMCs. However, powder metallurgy routes are much more expensive and only parts of limited sizes can be produced by this method. Another solid state process Friction Stir Processing (FSP) has successfully evolved as an alternative technique to fabricating metal matrix composites. FSP is based on the principles of Friction Stir Welding (FSW). In FSW, a rotating tool with a pin and a shoulder is inserted into the material to be joined, and traversed along the line of the joint. The friction between the tool and the work piece result in localized heating that softens and plasticizes the material. During production of MMCs using FSP method, the material undergoes intense plastic deformation resulting in mixing of ceramic particles and the metal. FSP also results in significant grain refinement of the metal and has also been used to homogenize the microstructure. FSP technology has also been used to fabricate surface/bulk composites of Al-SiC, friction stir surfacing of cast aluminum silicon alloy with boron carbide and molybdenum disulphide powders and to produce ultra-fine grained Cu-SiC composites. A major problem in the FSP of MMCs is severe tool wear that results from abrasion with hard ceramic particles. The progressive wear of the tool has been reported to increase the likelihood of void or defect development. This change in geometry has been reported in the friction stir welding of several MMCs. The problems concerning the tool life has become a serious issue in the application of FSP for producing MMCs. In the present work the advantages of the PDC method and FSP have been combined to produce polymer derived nano ceramic MMCs. This method mainly consists of three steps. In the first step, a polymer, which pyrolysis to form a PDC at temperatures lower than the melting point of the metal, is dispersed in the metal by FSP. This step is different from the melt route where the PDC forms at temperatures above the melting point of the metal. In the second step, external pyrolysis of the polymer dispersed material is carried out. Since this is a solid state process at stresses much higher than the shear or fracture of the polymer is expected to get evenly and finely distribution in the metal. This is done by heating the polymer dispersed material to a temperature above the pyrolysation temperature of the ceramic but lower than the melting point of the metal matrix. It should be mentioned that some pyrolysis of the polymer is possible during the FSP process itself. In the third step FSP is carried out on the pyrolised material for removing porosity that would form due to gas evolution during pyrolysis and to get a more uniform dispersion of polymer derived ceramic particles in the matrix. This method will produce nano-scale metal matrix composites with a relatively high volume fraction of the ceramic phase. This method can be extended to big sheets or a particular region in a sheet with no or low wear of tools. The material selected for the present study were pure Copper (99.9%) and Nickel Aluminum Bronze (NAB) copper alloy. The polymer precursor was poly (urea methyl vinyl) silazane, which is available commercially as CERASET. The polymer consists of silicon, carbon, nitrogen, oxygen and hydrogen atoms. The liquid precursor was thermally cross-linked into a rigid polymer, which was milled into a powder. This powder, having angular shaped particles of an average size of 10 µm, was used as the reinforcement. The polysilazanes convert into a highly refractory and amorphous ceramic upon pyrolysis and is known as polymer-derived silicon carbonitride which consists principally of silicon, carbon and nitrogen. The in-situ process is feasible because copper melts above the temperature at which the organic phase begins to pyrolise. The polysilazanes pyrolise in the temperature range of 973 to 1273 K, which lie below the melting temperature of copper, 1356K.The precursor has a density of approximately 1 gcm-3 in the organic phase and approximately 2 gcm-3 in the ceramic state. In the present work, we seek to introduce approximately 20 vol% of the ceramic phase into copper. The microstructure and mechanical properties of the developed copper-based in-situ polymer derived nano MMCs have been characterized in detail to understand the distribution of particles. The microstructure of the as received, processed as well as the FSP composite material was characterized using Optical Microscope (OM), Scanning Electron Microscope (SEM), Electron Probe Micro Analyzer (EPMA) and Transmission Electron Microscope (TEM). OM and SEM microstructural observations show that PDC particles are distributed uniformly with a bimodal (submicron+micron) distribution. In addition, TEM micrographs reveal the formation of very fine PDC particles of diameter 10-30 nm. X-ray diffraction and Thermo-gravimetric analysis confirms the presence of ceramic phase (Si3N4/SiC) in the matrix. Significant improvement in mechanical properties of the FSP PD-MMCs has been observed. This in-situ formed Cu/PDC composites show five times increase in micro-hardness (260Hv - 2.5GPa) compared to processed copper base metal and in-situ NAB/PDC composite shows two times increase in micro-hardness (325Hv- 3.2GPa) compared to NAB matrix. The Cu-PDC composites exhibited better tensile strength at room temperature. In-situ formed Cu-PDC composite’s yield strength increased from 110MPa to 235MPa as compared to processed base metal, where as ultimate tensile strength increases from 246MPa to 312MPa compared to processed base metal at room temperature. This strengthening could be attributed to the presence of in-situ formed hard phases and the concomitant changes in the microstructure of the matrix material such as reduction in grain size and contribution from Orowan strengthening. In the present work, we have observed tool wear by observing tool after each FSP pass and apart from producing a significantly harder material with higher elastic modulus, possibly for the first time, the issue of tool wear has been overcome. This is due to the fact that the composite is made by the polymer route and that the ceramic fractures easily till it reaches the nano-size. Wear studies of this composite was carried out in a pin-on-disc machine by sliding a pin made from the composite against an alumina disc. The wear rate of the FSP PD-MMC composites increased from 1.63×10-5 to 5.72×10-6 mm3/Nm. Improved wear resistance could be attributed to the presence of the in-situ formed hard nano-phase.