In this study, a two phase investigation of the hydraulic conductivity parameters of silty soils was performed. In the first phase, double-ring infiltrometer tests were used to measure infiltration rates in-situ at two sites in the Piedmont physiographic province of Georgia. The efficacy of predicting saturated hydraulic conductivity for Piedmont soils via published soil surveys from the National Resource Conservation Service and pedotransfer functions was then investigated. Work focused on the development of a consistent test methodology for soils (sandy, to silts and clays) in the Piedmont, and the final test method utilized being the constant head test, using a double-ring infiltrometer with Mariotte tubes to maintain the head. In the second phase of the investigation, laboratory based measurements of the saturated hydraulic conductivity of binary mixtures of fine sand and nonplastic silt were performed to investigate the effects of particle mixtures on hydraulic conductivity. The materials used were ASTM 100/200 sand and Sil-Co-Sil 40 non-plastic silt, chosen based on the ratio of the mean particle diameters. Significant effort was invested in the development and comparison of methodologies to produce uniform specimens of the binary mixtures for hydraulic conductivity testing, with the final being modified dry tubing. Two fixed densities were used to investigate the effects of particle packing on the hydraulic conductivity of binary mixtures, with critical fines contents chosen to ensure the finer particles primarily filled the pore volume of the coarse particles. Incremental fines contents, by mass, up to this theoretical fines content were tested. The measured saturated hydraulic conductivity was evaluated in terms of fines content, global and intergranular void ratio, and confining stress. Models for predicting extreme void ratios and saturated hydraulic conductivity of binary mixtures were also investigated.

Les matériaux constitutifs des digues sont souvent des sables silteux dont le comportement mécanique peut manifester une « instabilité » à des états de contraintes situés bien avant la limite de plasticité de Mohr-Coulomb. Ce mécanisme de rupture pourrait expliquer plusieurs brèches dont l'occurrence n'a pas été attribuée aux mécanismes classiques de rupture de digues telle que l'érosion interne. L'objectif de cette thèse est de mieux comprendre, au regard de ce phénomène d'instabilité, le comportement mécanique d'un sable silteux provenant de la zone adjacente à une brèche de digue du Rhône lors de la crue de 2003, à l'aide d'essais triaxiaux.Les résultats sur le sable propre montrent que le matériau étudié est très sensible au phénomène d'instabilité. Ce dernier peut être prédit par une courbe d'instabilité reliant, au déclenchement de l'instabilité, le rapport des contraintes au paramètre d'état. L'analyse de ces résultats suggère qu'une forte contractance du matériau est la condition nécessaire pour que l'instabilité du sable lâche ait lieu et qu'une direction appropriée du vecteur d'incrément de contraintes est la condition suffisante.Les résultats sur les mélanges constitués du sable avec des fines montrent qu'un départ de fines, causé par exemple une érosion de type suffusion, favorise l'occurrence de l'instabilité dans les digues. Par ailleurs, ces résultats révèlent que l'indice des vides équivalent est un paramètre pertinent dans l'analyse du comportement du sable silteux. Le calcul de l'indice des vides équivalent nécessite la détermination du paramètre b pour lequel une nouvelle formule a été proposée. / The constitutive materials of dikes are often silty sands whose mechanical behavior can become unstable at stress states located well under the Mohr-Coulomb plasticity limit criterion. This failure mechanism could explain several dike breaches whose occurrence has not been assigned to conventional mechanisms of dike failure such as internal erosion. The objective of this thesis is to better understand, with respect to the instability phenomenon, the mechanical behavior of a silty sand which is collected in the area adjacent of a breach of the Rhone embankment dike during the flood of 2003, by means of triaxial tests.The test results obtained on clean sand show that this material is very sensitive to the instability phenomenon. The occurrence of the latter can be predicted by an instability curve relating, at the onset of instability, the stress ratio to the state parameter. The analysis of these results suggests that a strong contractiveness of the material is the necessary condition for instability of loose sand and an appropriate direction of stress increment vector is the sufficient condition.The test results obtained on mixtures of sand with fines show that a removal of fine particles caused by an erosion, such as suffusion for example, favors the occurrence of instability in the dikes. Moreover, these results indicate that the equivalent void ratio is a relevant parameter in analyzing the behavior of silty sand. The calculation of the equivalent void ratio requires the determination of the parameter b for which a new formula has been proposed.