Internal combustion engine emissions are currently a major source of air pollution. The harmful impact of engine emissions can be reduced when engines are fuelled by alternatives to petrol and diesel such as natural gas. The use of lean burn technology in spark-ignition engines has been dominant; however, the lean burn technique can not economically satisfy the increasingly restricted future emission standards particularly for NOx emissions. In this thesis, the use of the stoichiometric air-fuel mixture with exhaust gas recirculation (EGR) technique in a spark ignition natural gas engine is investigated. The aim of the research is to optimize the key engine operating conditions in order to obtain the lowest NO emissions accompanied with low fuel consumption and high power. This is achieved via both experimental and computer simulation research. / PhD Doctorate

The losses in an internal combustion engine are dominated by thermal and parasitic sources. The latter arises from mechanical inefficiencies inherent within the system, particularly friction in load bearing conjunctions such as the piston assembly. During idle and at low engine speeds, frictional losses are the major contributor to the overall engine losses as opposed to the dominant contribution of thermal losses under other driving conditions. Given the relatively small size and simple structure of the top compression ring, it has a disproportionate contribution to the total frictional losses. This suggests further analysis would be required to understand the underlying causes of compression ring behaviour throughout the engine cycle. The available literature on tribological analyses of compression rings does not account for the transient ring elastodynamics. They usually assume a rigid ring for film thickness and power loss predictions, which is not representative of the ring's dynamic response. A combined study of ring elastodynamic behaviour and its tribological conjunction is a comprehensive approach.

[pt] É realizado um estudo teórico experimental sobre motores a combustão interna operando com taxa de compressão variável. É feita uma análise teórica sobre determinado mecanismo que permite variar a taxa de compressão. Para tal foi utilizado um programa de simulação para motores com ignição por centelha. No presente trabalho o modelo de simulação foi aprimorado, com a inclusão de previsão de detonação, de emissão de hidrocarbonetos, do cálculo da potencia de atrito, assim como a inclusão do dispositivo do mecanismo de taxa de compressão variável, entre outras alterações. Uma parte experimental foi também realizada, como o objetivo de validar os resultados do modelo teórico e de quantificar os benefícios proporcionados pelo mecanismo em questão. Para tal um motor de pesquisa de combustível – motor CFR – foi utilizado. Uma comparação dos resultados teóricos e experimentais obtidos no presente trabalho com os de outros pesquisadores é também apresentada. / [en] The present work is concerned with a theoretical and expererimental study of variable compression ratio spark ignition internal combustion engines. A theoretical analysis of the engine, operating with a mechanism allows for variable compression ratio, is carried out. For that a simulation program is utilized. In the present work the simulation model was updated with the inclusion of friction, knocking and hidrocarbon emission models, among other things. An experimental work was also carried out, with a CFR engine. The objective was a wo-fold to validade the results of the theoretical model and to assens the benefits of running an engine with variable compression ratio. A comparison is also made between the rrsults of the present work and those from other authors.

Pre-Chamber combustion systems are gaining popularity in Internal Combustion Engines (ICE) with the increasing emissions regulations due to their advantages in improving fuel economy by increasing the lean limit and cutting emission, especially NOx. In pre-chamber Combustion, flame jets shoot out from the pre-chamber orifices into the main chamber and generates several ignition points that promote a rapid burn rate of the lean mixture (air-excess ratio (λ) >1) in the main chamber. This work focused on studying two different fuels in the main chamber, lean limit, combustion efficiency (ηc), and emissions. A single-cylinder heavy-duty engine equipped with a narrow throat active pre-chamber was used. Two fuels were tested in the main chamber, Methane (CH4) and Ethanol (C2H5OH), the first fuel is used as a baseline, while keeping the pre-chamber fueled by Methane only. The engine was operated at a fixed speed, intake pressure, and spark-timing. The amount of fuel injected was varied to attain different global λ, then at each global λ; the amount of fuel injected to the Pre-chamber was varied to observe the effect of the pre-chamber λ. Different air intake temperatures were tested to see the effect on combustion efficiency. Results from the study showed an increase in the lean-limit using Ethanol in the main chamber compared to using only Methane in both chambers. However, lower ηc than that of the Methane was reported; this is due to a combination of the narrow-throat feature and the high heat of vaporization of Ethanol, ηc showed improvement when the air intake temperature increased.

This thesis discusses the thermoeconomic modeling and simulation of micro-CHP systems powered by various prime movers. Micro Cooling, Heating, and Power (micro-CHP) is becoming an increasingly important energy option as the demand for electrical power as well as heating and cooling for buildings increases worldwide. Micro-CHP has the potential to increase the total energy efficiency for cooling, heating, and powering residences, offices, and other relatively small buildings by using waste thermal energy from electricity production to deliver heating and cooling. Calculation methodologies are presented for the different components of micro CHP systems using thermodynamic cycles and mass and energy balances. System performance characteristics are calculated and compared for different prime movers using various fuels. Performance characteristics that are compared include fuel consumption, monthly energy savings, and system energy efficiencies.

No description available.

For an engine running at a constant speed, both exhaust and intake processes are periodic in nature. This inspires the muffler designer to go for the much easier and faster frequency domain modeling. But analogous to electrical filter, as per Thevenin’s theorem, the acoustic filter or muffler requires prior knowledge of the load-independent source characteristics (acoustic pressure and internal impedance), corresponding to the open circuit voltage and internal impedance of an electrical source. Studies have shown that it is not feasible to evaluate these source characteristics making use of either the direct measurement method or the indirect evaluation method. Hence, prediction of the radiated exhaust or intake noise has been subject to trial and error. Making use of the fact that pressure perturbation in a duct is a superposition of the forward moving wave and the reflected wave, a simple hybrid approach has been proposed making use of an interrelationship between progressive wave variables of the linear acoustic theory and Riemann variables of the method of characteristics. Neglecting the effect of nonlinearities, reflection of the forward moving wave has been duly incorporated at the exhaust valve. The reflection co-efficient of the system downstream of the exhaust valve has been calculated by means of the transfer matrix method at each of the several harmonics of the engine firing frequency. This simplified approach can predict exhaust noise with or without muffler for a naturally aspirated, single cylinder engine. However, this proves to be inadequate in predicting the exhaust noise of multi-cylinder engines. Thus, estimation of radiated noise has met only limited success in this approach. Strictly speaking, unique source characteristics do not exist for an IC engine because of the associated non-linearity of the time-varying source. Yet, a designer would like to know the un-muffled noise level in order to assess the required insertion loss of a suitable muffler. As far as the analysis and design of a muffler is concerned, the linear frequency-domain analysis by means of the transfer matrix approach is most convenient and time saving. Therefore, from a practical point of view, it is very desirable to be able to evaluate source characteristics, even if grossly approximate. If somehow it were possible to parameterize the source characteristics of an engine in terms of basic engine parameters, then it would be possible to evaluate the un-muffled noise before a design is taken up as a first approximation. This aspect has been investigated in detail in this work. A finite-volume CFD (one dimensional) model has been used in conjunction with the two-load or multi-load method to evaluate the source characteristics at a point just downstream of the exhaust manifold for the exhaust system, and upstream of the air filter (dirty side) in the case of the intake system. These source characteristics have been extracted from the pressure time history calculated at that point using the electro-acoustic analogy. Systematic parametric studies have yielded approximate empirical expressions for the source characteristics of an engine in terms of the basic engine parameters like engine RPM, capacity (swept volume or displacement), air-fuel ratio, and the number of cylinders. The effect of other parameters has been found to be relatively insignificant. Unlike exhaust noise, the intake system noise of an automobile cannot be measured because of the proximity of the engine at the point of measurement. Besides, the intake side is associated with turbocharger (booster), intercooler, cooling fan, etc., which will make the measurement of the intake noise erroneous. From the noise radiation point of view, intake noise used to be considered to be a minor source of noise as compared to the exhaust noise. Therefore, very little has been done or reported on prediction of the intake noise as compared to the exhaust noise. But nowadays, with efficient exhaust mufflers, the un-muffled intake noise has become a contributing factor to the passenger compartment noise level as a luxury decisive factor. Therefore, in this investigation both the intake and the exhaust side source characteristics have been found out for the compression ignition as well as the spark ignition engines. Besides, in the case of compression ignition engines, typical turbocharged as well as naturally aspirated engines have been considered. One of the inputs to the time-domain simulation is the intake valve and exhaust valve lift histories as functions of crank angle. It is very cumbersome and time-consuming to measure and feed these data into the program. Sometimes, this data is not available or cannot be determined easily. So, a generalized formula for the valve lift has been developed by observing the valve lift curves of various engines. The maximum exhaust valve lift has been expressed as a function of the swept volume of the cylinder. This formulation is not intended for designing a cam profile; it is for the purpose of determining approximate thermodynamic quantities to help a muffler designer for an initial estimation. It has also been observed during the investigation that from the acoustic point of view, sometimes it is better to open the exhaust valve a little earlier, but very slowly and smoothly, and keep it open for a longer time. Although the exact source characteristics for an automobile engine cannot be determined precisely, yet the values of source characteristics calculated using this methodology have been shown to be reasonably good for approximate prediction of the un-muffled noise as well as insertion loss of a given muffler. The resultant empirical expressions for the source characteristics enable the potential user to make use of the frequency-domain cum-transfer matrix approach throughout; the time consuming time-domain simulation of the engine exhaust source is no longer necessary. Predictions of the un-muffled sound pressure level of automotive engines have been corroborated against measured values as the well as the full scale time-domain predictions making use of a finite-volume software.

<p>Biomass is one of the main natural resources in Sweden.Increased utilisation of biomass for energy purposes incombined heat and power (CHP) plants can help the country meetits nuclear phase-out commitment. The present low-CO2 emissioncharacteristics of the Swedish electricity production system(governed by hydropower and nuclear power) can be retained onlyby expansion of biofuels in the CHP sector. Domestic Swedishbiomass resources are vast and renewable, but not infinite.They should be utilised as efficiently as possible in order tomeet the conditions for sustainability in the future.Application of efficient power generation cycles at low cost isessential for meeting this challenge. This applies also tomunicipal solid waste (MSW) incineration with energyextraction, which is to be preferred to landfilling.</p><p>Modern gas turbines and internal combustion engines firedwith natural gas have comparatively low installation costs,good efficiency characteristics and show reliable performancein power applications. Environmental and source-of-supplyfactors place natural gas at a disadvantage as compared tobiofuels. However, from a rational perspective, the use ofnatural gas (being the least polluting fossil fuel) togetherwith biofuels contributes to a diverse and more secure resourcemix. The question then arises if both these fuels can beutilised more efficiently if they are employed at the samelocation, in one combined cycle unit.</p><p>The work presented herein concentrates on the hybriddual-fuel combined cycle concept in cold-condensing and CHPmode, with a biofuel-fired bottoming steam cycle and naturalgas fired topping gas turbine or engine. Higher electricalefficiency attributable to both fuels is sought, while keepingthe impact on environment at a low level and incorporating onlyproven technology with standard components. The study attemptsto perform a generalized and systematic evaluation of thethermodynamic advantages of various hybrid configurations withthe help of computer simulations, comparing the efficiencyresults to clearly defined reference values.</p><p>Results show that the electrical efficiency of hybridconfigurations rises with up to 3-5 %-points in cold-condensingmode (up to 3 %-points in CHP mode), compared to the sum of twosingle-fuel reference units at the relevant scales, dependingon type of arrangement and type of bottoming fuel. Electricalefficiency of utilisation of the bottoming fuel (biomass orMSW) within the overall hybrid configuration can increase withup to 8-10 %-points, if all benefits from the thermalintegration are assigned to the bottoming cycle and effects ofscale on the reference electrical efficiency are accounted for.All fully-fired (windbox) configurations show advantages of upto 4 %-points in total efficiency in CHP mode with districtheating output, when flue gas condensation is applied. Theadvantages of parallel-powered configurations in terms of totalefficiency in CHP mode are only marginal. Emissions offossil-based CO2 can be reduced with 20 to 40 kg CO2/MWhel incold-condensing mode and with 5-8 kg CO2 per MWh total outputin CHP mode at the optimum performance points.</p><p>Keywords: Biomass, Municipal Solid Waste (MSW), Natural Gas,Simulation, Hybrid, Combined Cycle, Gas Turbine, InternalCombustion Engine, Utilization, Electrical Efficiency, TotalEfficiency, CHP.</p>

In the first part of studies, Controlled Auto-Ignition (CAI) combustion was investigated in a Ricardo E6 single cylinder, four stroke gasoline engine. CAI combustion is achieved by employing positive valve overlap configuration in combination with various compression ratios and intake air temperature strategies. The CAI operational region is limited by engine load due to knock and partial burned boundaries. The combustion characteristics and emissions are studied in order to understand the major advantages and drawbacks of CAI combustion with positive valve overlap. The enlargement of the CAI operational region is obtained by boosting intake air and external EGR. The lean-boosted operation elevators the range of CAI combustion to the higher load region, and the use of external EGR allows the engine to operation with CAI combustion in the mid range of region between boosted and N/A CAI operational range. The results are analyzed and combustion characteristics, performance and emissions are investigated. A Ricardo Hydra single cylinder, four stroke optical gasoline engine with optical access is then experimented to investigate CAI combustion through negative valve overlap configuration and an intake heater. The effects of direct fuel injection timings spark timings and air/fuel ratio are studied by means of simultaneous incylinder heat release study and direct visualization, chemiluminescence techniques which uses full, OH radical and CHO species. Both heat release analysis and chemiluminescence results have identified the pressure of minor combustion during the NVO period. Both the charge cooling and local air/fuel ratio effects are also investigated by varying the quantity of direct air injection.

Desde a sua invenção, o motor a combustão interna sofreu significantes evoluções, como redução do consumo de combustível, aumento da sua potência e durabilidade a um menor custo. Outros setores também evoluíram, como a busca por alternativas de combustível, tendo como exemplo o etanol hidratado combustível, que trouxe vantagens tais como maior desempenho e menor emissão de poluentes, porém com solicitações mecânicas, térmicas e termomecânicas mais severas. Sua menor lubricidade, quando comparada a da gasolina tipo C também intensificou o desgaste no par tribológico válvula e sede de válvula. Neste trabalho foram analisados diversos pares de válvulas e sedes de válvulas provenientes de quatro motores pós teste, sendo dois deles de mesma especificação técnica e submetidos às mesmas condições de ensaio, variando somente o combustível utilizado (etanol hidratado combustível e gasolina comum tipo C). A topografia da superfície de contato foi avaliada através de exames das superfícies com lupa estereoscópica, microscópio eletrônico de varredura e perfilômetro óptico a fim de identificar os danos encontrados. Ao término das análises foi realizada a comparação dos danos encontrados entre a superfície de contato das válvulas e sedes do motor que operou com etanol hidratado combustível e gasolina comum tipo C, de forma a evidenciar as diferenças proporcionadas pelos combustíveis. Este trabalho faz parte do \"Consórcio de P&D e Desafios Tribológicos em Motores Flex-Fuel\" patrocinado pela FAPESP (Fundação de Amparo à Pesquisa do Estado de São Paulo) com participação da indústria automotiva, para identificar os modos de desgaste atuantes. / Since its invention the internal combustion engine presented significant improvements like lower fuel consumption, higher power and durability increase at reduced costs. Other industries sectors did also improve as the search for new alternative fuels such as hydrated ethanol fuel which brought advantages like higher performance with lower pollutant emissions, although with it came more severe mechanical, thermal and thermo-mechanic stresses. Ethanol lower lubricity when compared to type C gasolines did also increase the valve/ valve seat insert wear. This study presents the results of contact surface analysis of several pairs valve/ valve seat insert from four engines after test being two of them of same technical specification and submitted to the same test cycle with only difference their fuel (hydrated ethanol and regular type C gasoline). The contact surface topography was evaluated through surface exams using optical microscopy, scanning electron microscope and non-contact profiler, to evaluate damages. At the end of analysis, a comparison between valves and valve seats from the engines that operated with hydrated ethanol and regular type C gasoline in order to put in evidence the damage difference provided by the fuels. This study is part of \"Consórcio de P&D e Desafios Tribológicos em Motores Flex-Fuel\", sponsored by FAPESP (\"Fundação de Amparo à Pesquisa do Estado de São Paulo\") with participation of automotive industries, to characterize the existent wear.