The aim of this work is to investigate the energy consumption of the servo drive at different control settings. First, the theoretical part describes the servo drive as a mechatronic system with subsequent disassembly in terms of losses and efficiency, where all the losses that occur in the servo drives are defined. Subsequently, the theoretical part concludes with a chapter on controllers, thanks to which it is possible to control servo drives and describes their influence on the resulting control. In the practical part, a model of a DC motor with a linear axis and regulation was first created in the Simulink program. Subsequently, the Matlab program defined motion with linear acceleration and motion using S-curves, which controlled the model. Then the model was measured at different settings of the controllers and the resulting waveforms together with the energy values were compared with each other. In the second half of the practical part of this work, a real servo drive was then measured with a subsequent comparison with the created model. In this comparison, the resulting waveforms and energy values were also compared. The result of this work is then to determine the effect of changes on the resulting control, which are made in the controller settings. The functional models can then be used to determine how the various servo drives will behave under the given control conditions.

This thesis is focused on voltage regulation in low voltage distribution system. It describes power management methods using photovoltaic inverters. The thesis describes the working PQ space of the inverter and the regulation characteristics of the active and reactive power in dependence on the voltage. The practical part focuses on the simulation of specific PQU control settings on the test models created in PSCAD. The model is used as a basis for real measurement. Outputs obtained from measurement and simulation are validated in the text. The last part of the thesis identifies limits for connecting resources with and without support.

This thesis deals with the design of a power converter for induction heating of iron components designed for a power of at least 2.5 kW. The induction furnace forms a series resonant LC circuit. The thesis contains a description and a design of individual parts of the converter, including wiring diagrams and a design of printed circuit boards. At the end of the work are then described the mechanical construction, the course of recovery and testing the operation of the inverter.

This Diploma thesis deals with the design of induction heating inverter. The main subject is optimalization for blacksmiths. There is described the designing procedure for power components and also designing of control part. Then prototype of 10 kW induction heater was made.

This thesis examines issues connected to safe uninterruptible power supplies. The term safe uninterruptible power supply is used for an aggregate of devices providing power for appliances that participate in safe rapid shutdown of a power plant in case power from a usual source fails. The thesis is divided into two parts – theoretical and practical. Theoretical part deals with possibilities and ways of realizing an aggregation of safe uninterruptible power supply. Various devices that can appear in the section of a safe uninterruptible power supply are listed and each device is characterized. Appliances that can be provided for by the sources of safe uninterruptible power supply are mentioned as well. These appliances are listed in accordance with ČSN standard nr. 381120. The theoretical part concludes with new trends in realization of safe uninterruptible power supplies. One of these sources is a clean source technology that can also be implemented in various ways. Practical part contains a suggestion of a safe uninterruptible power supply for particular steam power plant. This suggested safe uninterruptible power supply consists of rectifiers, batteries, inverters and a dieselgenerator. Calculated parameters of each device at the conclusion of the practical part are followed by a diagram of the suggested section of safe uninterruptible power supply.

Práce se zabývá modelováním PMSM, jeho parametry a jejich získáváním. Dále je v práci popsán model měniče beroucí v potaz dead-time efekt. Tyto modely jsou implementovány společně s dalšími bloky v prostředí Matlab/Simulink a dohromady tvoří knihovnu pro vektorové řízení motorů FSL_MC_TOOL. Součástí práce je také měření a identifikace parametrů skutečného PMSM. Dále byly vytvořeny příklady simulací, v nichž je použit motor s těmito parametry a vyhodnocena přesnost simulace. Tímto jsou simulace ověřeny na reálném systému.

This thesis describes the design and implementation of the transistor inverter to the subject of power electronics first outcome of this thesis will transistorized inverter that will serve as a demonstration tool in laboratory practice course electrical power. The laboratory preparation, students will be able to virtually test your theory acquired knowledge of the issue. Part of the theoretical analysis will be proposed circuit simulation program through classes Spice.

This thesis deals with designing of an induction heating of small iron parts. This device should be primarily designed for a farrier practice or an artistic blacksmithing. Considering the practice, the referential heated iron part will be a horseshoe. The basis of this device is a power inverter with serial resonant circuit connected to inverter as a load. This thesis contains designing and development of electrical and mechanical parts of whole device. It means control circuits, resonant circuit, box for heated part, etc. At the end of this thesis is realization of the device, electrifying, optimization and testing. During the test the horseshoe was heated close to demanded temperature.

Thesis in the introductory section describes the theory of heat pumps, the principle of their functions, including components used in pumps. The thesis includes a description of the air-water heat pump indoor unit, which also includes a frequency converter. Electronic frequency converter produces waste heat that must be cooled. The most extensive part of the work therefore deals with the computational model of heat transfer in the exchanger. The output is a map of all heat pump operating points with checking cooling efficiency of the inverter. In the final part are recommended modifications of the cooler design.

The master thesis deals with proposal of size optimization of PV systems. According to results of optimization, alternative solutions of photovoltaic system were proposed for family house. From the perspective of costs efficiency were compared investment costs and savings of implementation of electricity supply directly to private consumption. Particularly for each of the proposed solution, profitability assessment of comparing purchasing costs and returns on investment was performed. Theoretical part of the master thesis consists of introduction into solar radiation principles, structure and functionality of photovoltaic systems, electronics inverters and accumulation of electric energy. The practical part is focused on measuring of electricity consumption in particular family house, calculation of sunlight intensity hitting tested house, making various solutions of photovoltaic power plants placed on the family house in order to evaluate returns on investments. In conclusion are summarized all results of investigated solutions according to economics aspects.