Magneto-optical materials such as permalloy can be used to create artificial spin- ice (ASI) lattices with antiferromagnetic ordering. Magneto-optical materials used to create diffraction lattices are known to exhibit magnetic scattering at the half- order Bragg peak while in the ground state. The significant drawbacks of studying the magneto-optical generation of OAM using x-rays are cost, time, and access to proper equipment. In this work, it is shown that the possibility of studying OAM and magneto-optical materials in the spectrum of visible light at or around 2 eV is viable. Using spectroscopic ellipsometry it is possible to detect a change in the magnetization of thin permalloy films with thicknesses between 5 and 20 nm. Patterns consistent with OAM were found at 1.95 eV using a square lattice with a 4𝜋 radial phase shift in the antiferromagnetic ground state. Evidence of magnetic scattering at the half-order Bragg peak using 1.95 eV was also found.

This thesis examines second-order optical nonlinear wave mixing processes in domain-disordered quasi-phase matching waveguides and evaluates their potential use in compact, monolithically integrated wavelength conversion devices. The devices are based on a GaAs/AlGaAs superlattice-core waveguide structure with an improved design over previous generations. Quantum-well intermixing by ion-implantation is used to create the quasi-phase matching gratings in which the nonlinear susceptibility is periodically suppressed. Photoluminescence experiments showed a large band gap energy blue shift around 70 nm after intermixing. Measured two-photon absorption coefficients showed a significant polarization dependence and suppression of up to 80% after intermixing. Similar polarization dependencies and suppression were observed in three-photon absorption and nonlinear refraction. Advanced modeling of second-harmonic generation showed reductions of over 50% in efficiency due to linear losses alone. Self-phase modulation was found to be the dominant parasitic nonlinear effect on the conversion efficiency, with reductions of over 60%. Simulations of group velocity mismatch showed modest reductions in efficiency of less than 10%. Experiments on second-harmonic generation showed improvements in efficiency over previous generations due to low linear loss and improved intermixing. The improvements permitted demonstration of continuous wave second-harmonic generation for the first time in such structures with output power exceeding 1 µW. Also, Type-II phase matching was demonstrated for the first time. Saturation was observed as the power was increased, which, as predicted, was the result of self-phase modulation when using 2 ps pulses. By using 20 ps pulses instead, saturation effects were avoided. Thermo-optically induced bistability was observed in continuous wave experiments. Difference frequency generation was demonstrated with wavelengths from the optical C-band being converted to the L- and U-bands with continuous waves. Conversion for Type-I phase matching was demonstrated over 20 nm with signal and idler wavelengths being separated by over 100 nm. Type-II phase matched conversion was also observed. Using the experimental data for analysis, self-pumped conversion devices were found to require external amplification to reach practical output powers. Threshold pump powers for optical parametric oscillators were calculated to be impractically large. Proposed improvements to the device design are predicted to allow more practical operation of integrated conversion devices based on quasi-phase matching superlattice waveguides.

Title: Magnetic nanostructures for recording and optical sensors Author: Eva Lišková Department: Institute of Physics, Charles University Supervisor: Prof. Ing. Štefan Višňovský, DrSc. Abstract: Magneto-optical (MO) spectra of multilayered structures with enhanced MO effect were studied using the polar and longitudinal Kerr spectroscopy with oblique angle of light incidence in the photon energy range 1.2 eV to 5 eV. The samples with Fabry- Perot cavity like architecture, were modeled using Yeh matrix formalism. Two sets of samples, with composition FeF2/Fe/FeF2 and AlN/Fe/AlN, were prepared by molecular beam epitaxy and sputtering. The relations were studied between the position of the enhanced peak in the MO spectra and the structure. Second part of this work was devoted to the Pt/Co/Pt structures and the influence of the ion implantation on MO spectra and structural composition. The studied multilayer structures present interest for MO sensor and memory applications. Keywords: Magneto-optical Kerr effect, Magneto-optical sensor, Fabry-Perot resonator, Ion implantation

Made available in DSpace on 2014-12-17T15:14:57Z (GMT). No. of bitstreams: 1 EdimilsonFS_DISSERT.pdf: 2546760 bytes, checksum: 08525df56e96d75f8d221757342883b4 (MD5) Previous issue date: 2012-02-17 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / In this work, we investigated the magnetic properties of a monocrystalline Fe thin film and of Fe(80 ?)/Cr(t)/Fe(80 ?) tri-layers, with the nonmagnetic metallic Cr spacer layer thickness varying between 9 ? < t < 40 ?. The samples were deposited by the DC Sputtering on Magnesium Oxide (MgO) substrates, with (100) crystal orientation. For this investigation, experimental magneto-optical Kerr effect (MOKE) magnetometry and ferromagnetic resonance (FMR) techniques were employeed. In this case, these techniques allowed us to study the static and dynamical magnetization properties of our tri-layers. The experimental results were interpreted based on the phenomenological model that takes into account the relevant energy terms to the magnetic free energy to describe the system behavior. In the case of the monocrystalline Fe film, we performed an analytical discussion on the magnetization curves and developed a numerical simulation based on the Stoner-Wohlfarth model, that enables the numerical adjustment of the experimental magnetization curves and obtainment of the anisotropy field values. On the other hand, for the tri-layers, we analyzed the existence of bilinear and biquadratic couplings between the magnetizations of adjacent ferromagnetic layers from measurements of magnetization curves. With the FMR fields and line width angular dependencies, information on the anisotropy in three layers was obtained and the effects of different magnetic relaxation mechanisms were evidenced. It was also possible to observe the dependence of the epitaxy of the multilayers with growth and sputtering parameters. Additionally it was developed the technique of AC magnetic susceptibility in order to obtain further information during the investigation of magnetic thin films / Nesta disserta??o investigamos as propriedades magn?ticas de um filme monocristalino de ferro e tricamadas com a composi??o Fe(80?)/Cr(t)/Fe(80?), variando as espessuras da camada met?lica n?o magn?tica separadora (Cr) entre 9? < t < 40?. As amostras foram depositadas pela t?cnica Sputtring DC sobre substrato de ?xido de Magn?sio (MgO) com orienta??o cristalina (100). Para esta investiga??o foram utilizadas as t?cnicas experimentais de magnetometria por efeito Kerr Magneto-?ptico (MOKE) e Resson?ncia Ferromagn?tica (FMR). Estas t?cnicas permitiram o estudo das propriedades est?ticas e din?micas da magnetiza??o das multicamadas. Os resultados experimentais foram interpretados com base no modelo fenomenol?gico que leva em considera??o os termos mais relevantes da energia livre magn?tica para descrever o comportamento do sistema. Para o filme monocristalino de ferro, realizamos uma discuss?o anal?tica das informa??es das curvas de magnetiza??o e desenvolvemos uma simula??o num?rica baseada no modelo de Stoner-Wohlfarth, possibilitando o ajuste num?rico das curvas de magnetiza??o experimentais e a obten??o do valor de campo de anisotropia. Para as tricamadas, analisamos a presen?a dos acoplamentos bilinear e biquadr?tico entre as magnetiza??es das camadas ferromagn?ticas adjacentes a partir das medidas das curvas de magnetiza??o. Com as depend?ncias angulares do campo de FMR e da largura de linha obtivemos informa??es sobre as anisotropias presentes nas tricamadas e evidenciamos os efeitos de diversos mecanismos de relaxa??o magn?tica. Tamb?m foi poss?vel observar a depend?ncia da epitaxia das multicamadas com os par?metros de crescimento do Sputtering. Adicionalmente foi desenvolvida, durante o per?odo do mestrado, a t?cnica de susceptibilidade magn?tica AC com o objetivo de obter resultados inovadores na investiga??o de filmes finos magn?ticos

Made available in DSpace on 2014-12-17T15:15:00Z (GMT). No. of bitstreams: 1 CharlieSG.pdf: 1382454 bytes, checksum: 2b54a2a0dcd81f1ca374af1328ff8c73 (MD5) Previous issue date: 2006-03-15 / Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico / n this master s dissertation a Kerr Magneto Optic s magnetometer effect was set up to do characterization of samples type films fine and ultra thin, these samples will be grown after the implementation of the sputtering technique at the magnetism laboratory of of this department. In this work a cooled electromagnet was also built the water and that it reaches close values to 10kOe with a gap of 22 mm including an area of uniform field of 25mm of diameter. The first chapter treats of the construction of this electromagnet from its dimensioning to the operation tests that involve measures of reached maximum field and temperature of the reels when operated during one hour. The second chapter is dedicated to the revision of the magnetism and the magnetization processes as well as it presents a theoretical base regarding the magnetic energies found in films and magnetic multilayer. In the sequence, the third chapter, is especially dedicated the description of the effects magneto opticians the effect kerr in the longitudinal, traverse and polar configurations, using for so much only the classic approach of the electromagnetism and the coefficients of Fresnel. Distinguished the two areas of observation of the effect regarding thickness of the film. The constructive aspects of the experimental apparatus as well as the details of its operation are explained at the room surrender, also presenting the preliminary results of the measures made in one serializes of permalloy films and concluding with the results of the characterization of the first films of iron and permalloy grown here at the theoretical and experimental physics department at UFRN / Nesta disserta??o de mestrado foi montado um magnet?metro de efeito Kerr Magneto-?ptico para fazer caracteriza??o de amostras tipo filme fino e ultrafino, amostras estas que ser?o crescidas ap?s a implementa??o da t?cnica de Sputtering no laborat?rio de magnetismo deste departamento. Neste trabalho tamb?m foi constru?do um eletro?m? arrefecido a ?gua e que atinge valores pr?ximos a 10 kOe com um gap de 22 mm abrangendo uma regi?o de campo uniforme de 25 mm de di?metro. O primeiro cap?tulo trata da constru??o deste eletro?m? desde o seu dimensionamento at? os testes de opera??o que envolvem medidas de campo m?ximo alcan?ado e temperatura das bobinas quando operando durante 1 hora. O capitulo 2 ? dedicado a uma revis?o do magnetismo e dos processos de magnetiza??o bem como apresenta uma base te?rica a respeito das energias magn?ticas encontradas em filmes e multicamadas magn?ticas. Na seq??ncia, o terceiro cap?tulo, ? dedicado a descri??o dos efeitos magneto ?pticos em especial o efeito kerr nas configura??es longitudinal, transversal e polar, utilizando para tanto somente a abordagem cl?ssica do eletromagnetismo e os coeficientes de Fresnel. Distinguindo em seguida, as duas regi?es de observa??o do efeito referentes a espessura do filme. Os aspectos construtivos do aparato experimental bem como os detalhes de sua opera??o s?o explanados no quarto capitulo, apresentando tamb?m os resultados preliminares das medidas efetuadas em uma serie de filmes de Permalloy e finalizando com os resultados da caracteriza??o dos primeiros filmes de ferro e Permalloy crescidos aqui no departamento de f?sica te?rica e experimental da UFRN

Orientador: Munir Salomão Skaf / Tese (doutorado) - Universidade Estadual de Campinas, Instituto de Quimica / Made available in DSpace on 2018-08-05T22:46:02Z (GMT). No. of bitstreams: 1 Sonoda_MiltonTaidi_D.pdf: 3606314 bytes, checksum: dd30d5b14e2acb05e75ed7277f70cead (MD5) Previous issue date: 2005 / Doutorado / Físico-Química / Doutor em Ciências

This thesis is divided into three main sections that deal with optical and magnetic thin films properties and their measurements techniques. Principles of the spectroscopic reflectometry and measurements of optical properties are described in the first part. Results of imaging reflectometry are most important. This technique is based on in situ monitoring of optical properties of SiO2 thin films during etching over the area cca 10 × 13 mm2. In next section magnetic properties of thin films and new apparatus built on the Institute of Physical Engineering of BUT are shown. Magnetic properties were observed by longitudinal magneto-optical Kerr effect. The construction of the device is based on a light beam with rectilinear polarization reflected from magnetic material with turned polarization. For investigation of local magnetic properties of microstructures a microscope objective focusing laser beam on the sample is used. The last part of the thesis is aimed on improving of a spin valve structure Co/Cu/NiFe. This work was done within the frame of the Erasmus project in Laboratoire Louis Néel in Grenoble. The goal was to achieve the value of GMR (Giant Magnetoresistance) as high as possible by changing of deposition parameters. This value describes the rate of resistances in different mutual directions of magnetization in trilayers.

The aim of this thesis is a systematic study of physical properties of magnetic multilayered nanostructures. Namely it include multilayered spin valves NiFe/Cu/Co with magnetic anisotropy iduced by magnetic field applied during the deposition. Induced magnetic anisotropy influences exchange interactions between magnetic layers and so it gives the possibility to control magnetic properties of nanolayers. This is important for applications in MRAM, magnetoresistive read heads and spin-transfer-torque devices. Magnetooptic spectroscopy and Kerr effect hysteresis loop measurement were used as effective probe techniques. Secondly we examinated Ar3+ rf sputtering influence on multilayer interface quality level. We found out, that Ar3+ irradiation during deposition process has a possitive effect on interface quality.

Two groups of magnetic oxides were investigated in this thesis. Thin films of La2/3Sr1/3MnO3 (LSMO) deposited by pulsed laser deposition (PLD) on SrTiO3 (STO) substrates were characterized by polar and longitudinal magneto-optical (MO) Kerr spectroscopy. Experimental results were compared to theoretical calculations based on the transfer matrix formalism. A very good agreement between experimental and theoretical data revealed high magnetic ordering down to 5 nm of film thickness as well as a mechanism of suppression of double exchange interaction near the LSMO/STO interface. Magnetically doped Ce1-xCoxO2-δ films deposited by PLD on MgO (x = 0.05 and 0.10) and oxidized Si (x = 0.20) substrates were studied by combination of spectroscopic ellipsometry and MO Faraday and Kerr spectroscopy. Both diagonal and off-diagonal permittivity tensor components were obtained and verified by theoretical calculations confronted with experimental data. Diagonal spectra revealed two optical transitions from oxygen to cerium states. Off-diagonal spectra revealed two paramagnetic transitions involving cobalt ions. An essential influence of cobalt doping on the resulting ferromagnetic properties of CeO2 was observed.

Modification of interfaces in nanostructures can significantly influence their overall properties. Magneto-optical spectroscopy and spectroscopic ellipsometry are ideal for studying these phenomena thanks to their in-depth sensitivity and contactless measurements. Two methods of nonreversible modification of magnetic properties, especially the magnetic anisotropy, are investigated. The measured spectral dependence of magneto-optical Kerr effect is compared to a theoretical calculation in order to determine the profile of the samples for different levels and methods of modification. In addition to this, ellipsometric measurements are performed on a device whose optical properties change by voltage application.