Advanced scanning magnetoresistive microscopy (SMRM) — a robust magnetic imaging and probing technique — is presented. It utilizes conventional recording heads of a hard disk drive as sensors. The spatial resolution of modern tunneling magnetoresistive sensors is nowadays comparable with more commonly used magnetic force microscopes. Important advantages of SMRM are the ability to detect pure magnetic signals directly proportional to the out-of-plane magnetic stray field, negligible sensor stray fields, and the ability to apply local bipolar magnetic field pulses up to 10 kOe with bandwidths from DC up to 1 GHz. The performance assessment of this method and corresponding best practices are discussed in the first section of this work. An application example of SMRM, the study on chemically ordered L10 FePt is presented in a second section. A constructed heater unit of SMRM opens the path to investigate temperature-dependent magnetic properties of the medium by recording and imaging at elevated temperatures. L10 FePt is one of the most promising materials to reach limits in storage density of future magnetic recording devices based on heat-assisted magnetic recording (HAMR). In order to be implemented in an actual recording scheme, the medium Curie temperature should be lowered. This will reduce the power requirements, and hence, wear and tear on a heat source — integrated plasmonic antenna. It is expected that the exchange coupling of FePt to thin Fe layers provides high saturation magnetization and elevated Curie temperature of the composite. The addition of Cu allows adjusting the magnetic properties such as perpendicular magnetic anisotropy, coercivity, saturation magnetization, and Curie temperature. This should lead to a lowering of the switching field of the hard magnetic FeCuPt layer and a reduction of thermally induced recording errors. In this regard, the influence of the Fe layer thickness on the switching behavior of the hard layer was investigated, revealing a strong reduction for Fe layer thicknesses larger than the exchange length of Fe. The recording performance of single-layer and bilayer structures was studied by SMRM roll-off curves and histogram methods at temperatures up to 180 °C In the last section of this work, SMRM advantages are demonstrated by various experiments on a two-dimensional magnetic vortex lattice. Magnetic vortex is a peculiar complex magnetization configuration which typically appears in a soft magnetic structured materials. It consists of two coupled sub-systems: the core, where magnetization vector points perpendicular to the structure plane, and the curling magnetization where magnetic flux is rotating in-plane. The unique properties of a magnetic vortex making it an object of a great research and technological interest for spintronic applications in sensorics or data storage. Manipulation of the vortex core as well as the rotation sense by applying a local field pulse is shown. A spatially resolved switching map reveals a significant "write window" where vortex cores can be addressed correctly. Moreover, the external in-plane magnet extension unit allow analyzing the magnetic vortex rotational sense which is extremely practical for magnetic coupling investigations of magnetic coupling phenomena.

En raison de leur constante d’anisotropie magnétocristalline particulièrement élevée,les nanoparticules de FePt cristallisant dans la phase « chimiquement » ordonnée L10présentent un grand intérêt pour la réalisation de média magnétiques discrets à très hautedensité (>1 Tb/in2) jusqu’à un diamètre limite de 3,5 nm. Nos travaux portent sur la synthèsepar voie chimique (thermolyse) de nanoparticules de FePt-ɣ, calibrées en taille (4 ≤ Ø ≤ 8 nm)et de composition chimique proche de Fe50Pt50. Par la suite, leur transition vers la variété L10est réalisée afin de leur assurer un comportement ferromagnétique fort à 300 K. En dépitd’une composition non homogène en fer au sein de chaque nanoparticule (coeur riche enplatine et surface davantage riche en fer), la phase L10 est obtenue après un recuit sousatmosphère réductrice (Ar/H2 5%) à des températures supérieures à 650°C. Par ailleurs, afinde prévenir la coalescence des nanoparticules lors du recuit, trois méthodes de protectionsdistinctes ont montré leur efficacité : une matrice de NaCl, des écorces de silice amorphe etde MgO cristallisé. Cette dernière méthode de protection a permis, une fois les recuitsréalisés, de redisperser les nanoparticules de FePt-L10 par le biais d’une modification de leursurface par des chaînes de Polyoxyde d’éthylène-thiol (Mn =2000 g.mol-1). Une encremagnétique est obtenue une fois ces nanoparticules mises en solution avec desmacromolécules de copolymères à blocs Polystyrène-b-Polyoxyde d’éthylène. Le dépôt decette encre sur un substrat permet de former, après auto-assemblage supramoléculaire desmacromolécules, un film hybride contenant les nanoparticules ferromagnétiques FePt-L10localisées sélectivement dans les domaines cylindriques de POE. / Nanoparticles made of FePt alloy in a face-centered-tetragonal (fct) structure have agreat interest for the enhancement of data density (> 1 Tbit/in²) in magnetic recordingmedia due to their high magneto-crystalline anisotropy and low critical diameters (3.5 nm).Our works lie in the synthesis of ɣ-FePt nanoparticles controlled in size (4 ≤ Ø ≤ 8 nm) andchemical composition (≈ Fe50Pt50) by thermal decomposition of organometallic precursors.Following ɣ-FePt NPs synthesis, annealing at high temperature is required for a completetransition from fcc to fct structure (L10) that ensure a ferromagnetic behavior at ambient.Despite a non-homogenous chemical composition on each nanoparticles (platinum-rich coreand iron-rich surface), L10 structure has been obtained after annealing under atmosphereAr/H2 (5%), at temperature up to 650°C. To prevent coalescence of FePt NPs duringannealing, tree distinct protection routes have shown their effectiveness: an inert NaClmatrix, an amorphous silica shell or a crystalline MgO shell. This last method shows bestresults in redispersion of L10-FePt nanoparticles after annealing via surface modification ofnanoparticles by PEO-thiol chains (Mn =2000 g.mol-1). A magnetic ink is then formulated inpresence of PS-b-PEO macromolecules. At least, this as-made ink is deposited on a substrateto obtain, after copolymer self-assembly, a hybrid film containing ferromagnetic L10-FePtnanoparticles selectively located into PEO cylindrical domains.

Advanced scanning magnetoresistive microscopy (SMRM) — a robust magnetic imaging and probing technique — is presented. It utilizes conventional recording heads of a hard disk drive as sensors. The spatial resolution of modern tunneling magnetoresistive sensors is nowadays comparable with more commonly used magnetic force microscopes. Important advantages of SMRM are the ability to detect pure magnetic signals directly proportional to the out-of-plane magnetic stray field, negligible sensor stray fields, and the ability to apply local bipolar magnetic field pulses up to 10 kOe with bandwidths from DC up to 1 GHz. The performance assessment of this method and corresponding best practices are discussed in the first section of this work. An application example of SMRM, the study on chemically ordered L10 FePt is presented in a second section. A constructed heater unit of SMRM opens the path to investigate temperature-dependent magnetic properties of the medium by recording and imaging at elevated temperatures. L10 FePt is one of the most promising materials to reach limits in storage density of future magnetic recording devices based on heat-assisted magnetic recording (HAMR). In order to be implemented in an actual recording scheme, the medium Curie temperature should be lowered. This will reduce the power requirements, and hence, wear and tear on a heat source — integrated plasmonic antenna. It is expected that the exchange coupling of FePt to thin Fe layers provides high saturation magnetization and elevated Curie temperature of the composite. The addition of Cu allows adjusting the magnetic properties such as perpendicular magnetic anisotropy, coercivity, saturation magnetization, and Curie temperature. This should lead to a lowering of the switching field of the hard magnetic FeCuPt layer and a reduction of thermally induced recording errors. In this regard, the influence of the Fe layer thickness on the switching behavior of the hard layer was investigated, revealing a strong reduction for Fe layer thicknesses larger than the exchange length of Fe. The recording performance of single-layer and bilayer structures was studied by SMRM roll-off curves and histogram methods at temperatures up to 180 °C In the last section of this work, SMRM advantages are demonstrated by various experiments on a two-dimensional magnetic vortex lattice. Magnetic vortex is a peculiar complex magnetization configuration which typically appears in a soft magnetic structured materials. It consists of two coupled sub-systems: the core, where magnetization vector points perpendicular to the structure plane, and the curling magnetization where magnetic flux is rotating in-plane. The unique properties of a magnetic vortex making it an object of a great research and technological interest for spintronic applications in sensorics or data storage. Manipulation of the vortex core as well as the rotation sense by applying a local field pulse is shown. A spatially resolved switching map reveals a significant "write window" where vortex cores can be addressed correctly. Moreover, the external in-plane magnet extension unit allow analyzing the magnetic vortex rotational sense which is extremely practical for magnetic coupling investigations of magnetic coupling phenomena.