An ID generating circuit is unquestionably the core of a chipless RFID tag. For convenience of printing process and cost consideration, the circuit should be kept as simple as possible. Based on the cognition, an 8-bit time-domain based ID generating circuit that merely consists of a ML and eight capacitors was offered, and implemented on photo-paper substrates via inkjet printing process. In addition to the experimental measurements, the circuit was also input into circuit simulators for cross-validation. The good agreement between simulations and measurements is observed, exhibiting the tag technical feasibility. Besides of low cost, the tag has wide compatibility with current licensed RFID spectrum, which will facilitate the future deployment in real applications. Compared   to  time-domain   based  chipless   tags,  frequency   signatures   based chipless RFID tags are expected to offer a larger coding capacity. As a response, we presented a 10-bit frequency-domain based chipless RFID tag. The tag composed of ten configurable LC resonators was implemented on flexible polyimide substrate by using  fast  toner-transferring  process.  Field  measurements  revealed  not  only  the practicability  of  the  tag,  but  also  the  high  signal  to  noise  ratio  (SNR).  Another frequency domain tag consists of a configurable coplanar LC resonator. With the use of all printing process, the tag was for the first time realized on common packaging papers.  The tag feasibility was confirmed by subsequent measurements. Owing to the ultra-low cost potential and large SNR, The tag may find wide applications in typical RFID solutions such as management of paper tickets for social events and governing of smart documents. Ultra wide band (UWB) technology possesses a number of inherent merits such as high speed communication and large capacity, multi-path immunity, accurate ranging and positioning, penetration through obstacles, as well as extremely low-cost and low- power transmitters. Thus, passive UWB RFIDs are expected to play an important pole in  the future identification applications for IoT. We explained the feature difference between  UWB  chipless  tags  and  chip  based  tags,  and  forecasted  the  applications respectively  based on the comparison  between the two technologies.  It is expected that the two technologies will coexist and compensate each other in the applications of IoT. Lastly, the thesis ends up with brief summary of the author’s contributions, and technical prospect for the future development of printable chipless RFID tags. / <p>QC 20140304</p>

Radio frequency identification (RFID) and sensing are two key technologies enabling the Internet of Things (IoT). Development of RFID tags augmented with sensing capabilities (RFID sensor tags) would allow a variety of new applications, leading to a new paradigm of the IoT. Chipless RFID sensor technology offers a low-cost solution by eliminating the need of an integrated circuit (IC) chip, and is hence highly desired for many applications. On the other hand, printing technologies have revolutionized the world of electronics, enabling cost-effective manufacturing of large-area and flexible electronics. By means of printing technologies, chipless RFID sensor tags could be made flexible and lightweight at a very low cost, lending themselves to the realization of ubiquitous intelligence in the IoT era. This thesis investigated three construction methods of printable chipless RFID humidity sensor tags, with focus on the incorporation of the sensing function. In the first method, wireless sensing based on backscatter modulation was separately realized by loading an antenna with a humidity-sensing resistor. An RFID sensor tag could then be constructed by combining the wireless sensor with a chipless RFID tag. In the second method, a chipless RFID sensor tag was built up by introducing a delay line between the antenna and the resistor. Based on time-domain reflectometry (TDR), the tag encoded ID in the delay time between its structural-mode and antenna-mode scattering pulse, and performed the sensing function by modulating the amplitude of the antenna-mode pulse. In both of the above methods, a resistive-type humidity-sensing material was required. Multi-walled carbon nanotubes (MWCNTs) presented themselves as promising candidate due to their outstanding electrical, structural and mechanical properties. MWCNTs functionalized (f-MWCNTs) by acid treatment demonstrated high sensitivity and fast response to relative humidity (RH), owing to the presence of carboxylic acid groups. The f-MWCNTs also exhibited superior mechanical flexibility, as their resistance and sensitivity remained almost stable under either tensile or compressive stress. Moreover, an inkjet printing process was developed for the f-MWCNTs starting from ink formulation to device fabrication. By applying the f-MWCNTs, a flexible humidity sensor based on backscatter modulation was thereby presented. The operating frequency range of the sensor was significantly enhanced by adjusting the parasitic capacitance in the f-MWCNTs resistor. A fully-printed time-coded chipless RFID humidity sensor tag was also demonstrated. In addition, a multi-parameter sensor based on TDR was proposed.The sensor concept was verified by theoretical analysis and circuit simulation. In the third method, frequency-spectrum signature was utilized considering its advantages such as coding capacity, miniaturization, and immunity to noise. As signal collision problem is inherently challenging in chipless RFID sensor systems, short-range identification and sensing applications are believed to embody the core values of the chipless RFID sensor technology. Therefore a chipless RFID humidity sensor tag based on near-field inductive coupling was proposed. The tag was composed of two planar inductor-capacitor (LC) resonators, one for identification, and the other one for sensing. Moreover, paper was proposed to serve as humidity-sensing substrate for the sensor resonator on accounts of its porous and absorptive features. Both inkjet paper and ordinary packaging paper were studied. A commercial UV-coated packaging paper was proven to be a viable and more robust alternative to expensive inkjet paper as substrate for inkjet-printed metal conductors. The LC resonators printed on paper substrates showed excellent sensitivity and reasonable response time to humidity in terms of resonant frequency. Particularly, the resonator printed on the UV-coated packaging paper exhibited the largest sensitivity from 20% to 70% RH, demonstrating the possibilities of directly printing the sensor tag on traditional packages to realize intelligent packaging at an ultra-low cost. / <p>QC 20150326</p>