In this diploma thesis is accomplished description of existing condition of decorating linear tractive unit. Analysis of safety requirements for linear tractive unit is also accomplished. Eligible construction concept of frame of electromechanical linear tractive unit is chosen. Selection and calculation of ball screw and nut is made also with draft of its eligible support . Choose of eligible engine and clutch for gearing of engine torque from engine to the ball screw is done too. Further is designed eligible concept of gearing of the rotary motion of ball screw to straight motion of bottom pulley block, which now interacting with upper firm pulley block provides lifting of tensile rod with coulisse.

Reconnaissance of problems and parameters of square hollow profile bend. Finding (identification) of deformation of cross-section. Finding of suitability of unannealed material for component part. Finding of mechanical characteristics of welds and influence of their bend position. This finding was done on the basis of comparison of tensile tests and consequently aplicated to specific part where the suitability for use of unannealed material were proved.

The master’s thesis deals with the computational modelling of the mechanical testing of isolated smooth muscle cells. The main aims are to create computational model of a cell, to simulate single-axis tensile test and to modify the model so that the model reflects real mechanical response. The model of the cell includes cytoplasm, nucleus, cell membrane and cytoskeleton which is modelled as a tensegrite structure. On this model the tensile test was simulated in case of the cell with cytoskeleton and the cell with distributed the cytoskeleton. Force-elongation curves, which were obtained from this simulation, were compared with experimental data which were taken from literature. Tensile properties were measured on freshly isolated cells from rat thoracic aorta, cultured cells, and cells treated with cytochalasin D to disrupt their actin filaments. It was found that the cytoskeleton influence on the cell load in computational model was smaller than in the real cell. Therefore the model was modified by changing material propreties and geometry so that the model of the cell corresponded with the different types of experimentally measured cells.

Cold spray is a novel coating method. Due to its low-temperature character, it has a potential to replace the high-temperature thermal spray processes in some applications. The presented work analyzes the microstructure and the phase composition of pure metal coatings deposited by cold spraying and evaluates selected mechanical properties. Specimens prepared by readily used HVOF industrial technology were used for comparison purposes.

Práce rozebírá projekt, který je základem znovupoužiteného enginu počítačové hry - tahové strategie. Celkovým cílem by mělo být vytvoření komerční série počítačových her z vojenského prostředí. Text technické zprávy rozebírá zadání projektu a rozšiřuje jeho myšlenky o nezbytné vlastnosti. Dále popisuje vytvoření samotného zdrojového kódu a jeho použití. Zmiňuje se o stávajícím stavu projektu a krocích, které je potřeba podniknout k jeho dokončení. Zpráva je v anglickém jazyce.

Práce byla zaměřena na ověření platnosti koncepce master křivky pro hodnocení heterogenních svarových spojů, resp. teplotně stárnutých svarů. Současně bylo cílem disertace vyvinout kvantitativní model pro predikci referenční teploty lokalizující tranzitní oblast na teplotní ose za použití dat získaných z tahové zkoušky, a to za použití metody umělých neuronových sítí. Studie je současně zaměřena na heterogenní svarový spoj připravený tavným svařováním. Je zacílena na hodnocení lomového chování v tranzitní oblasti nejméně odolné části svaru, tj. tepelně ovlivněné zóny ferritické oceli v blízkosti zóny natavení s vysokolegovaným materiálem. Pro predikci referenční teploty master křivky je použita zmíněná metoda neuronových sítí, a to za použití dat z tahových zkoušek a měření tvrdosti. Predikovaná referenční teplota byla ověřována na základě výsledku experimentálních měření. Vytvoření modelu za použití neuronových sítí vyžaduje dostatečné množství dat a není vždy snadno tuto podmínku splnit. V případě sledovaného problému to znamenalo použití dat z dostatečně věrohodných zdrojů (skupiny Křehký lom ÚFM AVČR) a se známou metalurgickou historií. Smysl práce je tak možno spatřovat ve vývoji modelu neuronové sítě, která bude dostatečně přesně predikovat referenční teplotu. Celkově byla pro tyto účely použita data z 29 nízkolegovaných ocelí. Pro účely vývoje byly použity kromě hladkých zkušebních tyčí, rovněž tahové zkoušky s obvodovým vrubem testované při kritické teplotě křehkosti (mez makroplastických deformací) a při teplotě pokojové. Při tvorbě modelu byla postupně v různých kombinacích využita všechna data z uvedených zkoušek. Studie ukázala, že referenční teplota charakterizující tranzitní chování lomové houževnatosti oceli s převažující feritickou strukturou je jedinečným parametrem predikovatelným na základě vybraných charakteristik tahových zkoušek.

This diploma thesis deals with proposal of a two-lane vertical boiler using the waste heat after gas turbine. In the first part the heat calculation has been done followed by the arrangement of particular heat exchange surfaces and the drawing of real saw diagram. There are also dimensions of drums, inlet and outlet pipes and transfer pipelines drafted. Furthermore, I have listed the materials that are used for casing the boiler and pipelines. Finally, the boiler loss is calculated and the boiler hydraulic calculation is performed. The supplement contains a boiler drawing.

This work deals with the study of diagnostic methods suitable for monitoring of the drying process of brick raw materials. Based on the extensive literature search, several parameters are selected, which are appropriate to monitoring during drying. In addition, a methodology for measuring these selected parameters is proposed. In the experimental part, the use of all described methods is gradually verified on the brick raw material with and without shortening additive (also known as grog). Was carried out: measurement of the surface temperature in the climatic chamber, determination of humidity distribution in the sample, determination of moisture diffusivity, determination of tensile strength, determination of ultrasonic wave velocity and determination of dynamic E-modulus of elasticity. Results of experiments and the gained experiences show, that at least two of the above-mentioned monitoring methods are very appropriate and beneficial – determination of moisture diffusivity and determination of tensile strength. In the work was described in detail the procedure of determination of moisture diffusivity of material. The dependence of moisture diffusivity on the moisture content of the dried material, has been described. Also, differences between raw material with grog and without grog has been described. As part of the practical verification of the experiment designed to determine the tensile strength at different humidity levels of test samples. A new shape of the test specimens and a new device were designed to allow them to be attached to a hydraulic press. The results of this work show that the tensile strength of the ceramic green bodies is primarily dependent on the moisture content of the material. The type of raw material almost does not affect the tensile strength.

This work is focused on the application of advanced elasto-plastic material model intended for shotcrete. Spatial mathematical models of two laboratory tests are created, where this model is used. The first test is a three-point bending concrete specimen. Next, the behavior of the material is analyzed, in which input parameters are entered. Consequently, two reverse analyzes of the available data are analyzed where a match between prediction and measurement can be obtained. The second test is a modified tensile test, where is describe the material behavior in changing of input parameters. Subsequently, reverse data analysis is created, where an acceptable match between prediction and measurement is possible. In every study, the stress waveform in the fracture process zone is analyzed to more detail.

This diploma thesis is focused on the surface hardening of cast irons with spheroidal graphite. The work describes a theoretical analysis of the structure and properties of cast irons and individual methods suitable for surface hardening. The practical part describes the production of cast iron castings with spheroidal graphite, on which the surface hardening is performed, tensile test, hardening of produced castings by induction and laser surface hardening, preparation of samples for measuring microhardness and metallographic analysis of metal structures.