<p>Thin films of refractory metals and carbides have been studied extensively over many years because of their wide range of application. The two major techniques used are Chemical Vapour Deposition (CVD) and Physical Vapour Deposition (PVD). These can result in the deposition of two-dimensional blanket or patterned thin films. Laser-assisted Chemical Vapour Deposition (LCVD) can provide a maskless alternative for localised deposition in two and three dimensions. This thesis describes LCVD of micrometer-sized tungsten, molybdenum and tungsten carbide rods. The kinetics, phase composition and microstructure have been studied as a function of in situ measured laser induced deposition temperature.</p><p>Tungsten and molybdenum rods were deposited by hydrogen reduction of their corresponding hexafluorides, WF6 and MoF6, respectively. Single crystal and polycrystalline tungsten rods were obtained, depending on the H2/WF6 molar ratio and deposition temperature. The molybdenum rods were either single crystals or dendritic in form depending on experimental conditions. The field emission characteristics of the tungsten single crystals were investigated. The results showed LCVD to be a potential fabrication technique for field emitting cathodes.</p><p>Nanocrystalline tungsten carbide rods were deposited from WF6, C2H4 and H2. TEM analysis showed that the carbide rods exhibited a layered structure in terms of phase composition and grain size as a result of the temperature gradient induced by the laser beam. With decreasing WF6/C2H4 molar ratio, the carbon content in the rods increased and the phase composition changed from W/W2C to WC/WC1-x and finally to WC1-x/C.</p>

<p>One important driving force in nanotechnology today is the change which can be made in the properties of a material when the dimensions of its individual building blocks are decreased below approximately 100 nm. Such small building blocks, typically nanoparticles, may induce new and unique properties compared to those of the corresponding bulk material. The challenge in nanotechnology is to make nanoparticles with a discrete particle size within the range 1-10 nm. It is also important to develop appropriate assembly methodologies in order to construct devices composed of such small building blocks.</p><p>This thesis reports iron nanoparticle synthesis using laser-assisted photolysis of ferrocene. The particles were protected against oxidation by a carbon shell formed in situ during their growth. By varying the experimental conditions such as fluence, repetition rate and laser beam area, particles could be synthesized in the size range 1 to 100 nm. Their size was measured using a differential mobility analyser (DMA), transmission electron microscopy (TEM) and X-ray diffraction (XRD). DMA was also used successfully to size-select particles to facilitate the deposition of monodisperse nanoparticle films.</p><p>A theoretical "residence time approach (RTA)" model was developed to relate particle volume to the laser parameters used. The growth of these particles was studied in situ using optical emission spectroscopy; the results were compared with those from quantum mechanical calculations. The particles were characterised ex situ by TEM, convergent beam electron diffraction, XRD, X-ray photoelectron spectroscopy and Raman spectroscopy. Results from the TEM investigations revealed that the carbon shell was graphitic close to the iron core, while the outer part of the carbon shell was amorphous, indicating different growth mechanisms. Both bcc and fcc iron particles were observed. </p>

Thin films of refractory metals and carbides have been studied extensively over many years because of their wide range of application. The two major techniques used are Chemical Vapour Deposition (CVD) and Physical Vapour Deposition (PVD). These can result in the deposition of two-dimensional blanket or patterned thin films. Laser-assisted Chemical Vapour Deposition (LCVD) can provide a maskless alternative for localised deposition in two and three dimensions. This thesis describes LCVD of micrometer-sized tungsten, molybdenum and tungsten carbide rods. The kinetics, phase composition and microstructure have been studied as a function of in situ measured laser induced deposition temperature. Tungsten and molybdenum rods were deposited by hydrogen reduction of their corresponding hexafluorides, WF6 and MoF6, respectively. Single crystal and polycrystalline tungsten rods were obtained, depending on the H2/WF6 molar ratio and deposition temperature. The molybdenum rods were either single crystals or dendritic in form depending on experimental conditions. The field emission characteristics of the tungsten single crystals were investigated. The results showed LCVD to be a potential fabrication technique for field emitting cathodes. Nanocrystalline tungsten carbide rods were deposited from WF6, C2H4 and H2. TEM analysis showed that the carbide rods exhibited a layered structure in terms of phase composition and grain size as a result of the temperature gradient induced by the laser beam. With decreasing WF6/C2H4 molar ratio, the carbon content in the rods increased and the phase composition changed from W/W2C to WC/WC1-x and finally to WC1-x/C.

One important driving force in nanotechnology today is the change which can be made in the properties of a material when the dimensions of its individual building blocks are decreased below approximately 100 nm. Such small building blocks, typically nanoparticles, may induce new and unique properties compared to those of the corresponding bulk material. The challenge in nanotechnology is to make nanoparticles with a discrete particle size within the range 1-10 nm. It is also important to develop appropriate assembly methodologies in order to construct devices composed of such small building blocks. This thesis reports iron nanoparticle synthesis using laser-assisted photolysis of ferrocene. The particles were protected against oxidation by a carbon shell formed in situ during their growth. By varying the experimental conditions such as fluence, repetition rate and laser beam area, particles could be synthesized in the size range 1 to 100 nm. Their size was measured using a differential mobility analyser (DMA), transmission electron microscopy (TEM) and X-ray diffraction (XRD). DMA was also used successfully to size-select particles to facilitate the deposition of monodisperse nanoparticle films. A theoretical "residence time approach (RTA)" model was developed to relate particle volume to the laser parameters used. The growth of these particles was studied in situ using optical emission spectroscopy; the results were compared with those from quantum mechanical calculations. The particles were characterised ex situ by TEM, convergent beam electron diffraction, XRD, X-ray photoelectron spectroscopy and Raman spectroscopy. Results from the TEM investigations revealed that the carbon shell was graphitic close to the iron core, while the outer part of the carbon shell was amorphous, indicating different growth mechanisms. Both bcc and fcc iron particles were observed.

<p>Due to the small dimensions, nanoparticles and materials consisting of nano-sized building blocks exhibit unique — mostly superior — properties, well differing from their bulk counterpart. Most of the novel properties of nanoparticles (and nanomaterials) are size-dependent, while the majority of the common gasphase methods used for generation of nanopowders result in different, usually wide, size-dispersions. Further understanding of the fundamental processes leading to particle formation is therefore required, leading to better control of size and distribution of the nanoparticles, thus allowing engineering of the desired properties for both nanoparticles and nanomaterials.</p><p>In this present thesis, nanoparticles were produced by two different gasphase techniques activated by lasers, namely laser chemical vapor deposition (LCVD) and pulsed laser ablation (PLA). Optical emission spectroscopy (OES) was performed on thermal (blackbody-like) radiation originating from laser-excited particles during LCVD and coupled to measured size-distributions. In-situ monitoring of size-distributions by a differential mobility analyzer (DMA) was employed during PLA. In addition, deposited nanoparticles were characterized by a variety of standard techniques.</p><p>Different cooling mechanisms of the laser-excited gasphase particles were identified based on temperature and emitted intensity data extracted from OES measurements. The strong evaporation at elevated temperatures also allowed direct size manipulation of the particles. By monitoring the intensity of the emitted thermal radiation and the scattered laser line, strong indications about the so called coagulation limit, where a broadening of the size-distribution occurred, was obtained. The DMA monitoring, supported by modeling, gave information about different mechanisms (thermal and photochemical) of the ablation process, and particle condensation well below the ablation threshold was also found.</p>

Due to the small dimensions, nanoparticles and materials consisting of nano-sized building blocks exhibit unique — mostly superior — properties, well differing from their bulk counterpart. Most of the novel properties of nanoparticles (and nanomaterials) are size-dependent, while the majority of the common gasphase methods used for generation of nanopowders result in different, usually wide, size-dispersions. Further understanding of the fundamental processes leading to particle formation is therefore required, leading to better control of size and distribution of the nanoparticles, thus allowing engineering of the desired properties for both nanoparticles and nanomaterials. In this present thesis, nanoparticles were produced by two different gasphase techniques activated by lasers, namely laser chemical vapor deposition (LCVD) and pulsed laser ablation (PLA). Optical emission spectroscopy (OES) was performed on thermal (blackbody-like) radiation originating from laser-excited particles during LCVD and coupled to measured size-distributions. In-situ monitoring of size-distributions by a differential mobility analyzer (DMA) was employed during PLA. In addition, deposited nanoparticles were characterized by a variety of standard techniques. Different cooling mechanisms of the laser-excited gasphase particles were identified based on temperature and emitted intensity data extracted from OES measurements. The strong evaporation at elevated temperatures also allowed direct size manipulation of the particles. By monitoring the intensity of the emitted thermal radiation and the scattered laser line, strong indications about the so called coagulation limit, where a broadening of the size-distribution occurred, was obtained. The DMA monitoring, supported by modeling, gave information about different mechanisms (thermal and photochemical) of the ablation process, and particle condensation well below the ablation threshold was also found.