The interaction of an unsteady wake with a solid body can induce sizable loading of the structure, which has many detrimental side effects in both the structural and acoustic senses. These interactions are ubiquitous in nature and engineering. A flow control technique is sought to mitigate this interaction, thereby decreasing the level of structural vibration. This thesis investigates the effectiveness of steady leading-edge blowing (LEB) flow control for modifying the vortex induced vibrations on an airfoil in the wake of a circular cylinder. The airfoil was allowed to oscillate perpendicular to the fluid flow direction in response to the impinging Von-Karman vortex street. The flow field and airfoil vibrations were simultaneously captured using Digital Particle Image Velocimetry (DPIV) and accelerometer measurements in a time-resolved sense. The results indicate that LEB can significantly reduce the degree of unsteady loading due to the blade vortex interaction (BVI). In some cases, the LEB jet appears to break the coherency of a vortex incident on the airfoil, and in other cases the jet increase the mean stand-off distance of the vortex as it convects over the airfoil surface. It was also found that, for large circular cylinders, if the airfoil is within the mean closure point of the circular cylinder wake, the LEB can increase the level of BVI. The Proper Orthogonal Decomposition (POD) was also used to analyze the DPIV data. POD is mathematically superior for reducing a data rich field into fundamental modes; a suitable basis function for the reduction is chosen mathematically and it is not left to the researcher to pick the basis function. A comparison of the energy in these modes is useful in ascertaining the dynamics of the BVI. For one of the two cases examined with POD, it was found for no LEB the fundamental (i.e. most energetic) mode is given by the vortex shedding of the circular cylinder upstream. The addition of LEB reduces the energy contained in this fundamental mode. Thus the LEB jet has the effect of reducing the flow field coherency; the structure of the large vortices is broken up into smaller vortices. For the other case, the LEB jet has the opposite effect: the jet has the ability to organize the circular cylinder wake into coherent structures. This acts to increase the coherency of the circular cylinder wake and increases the level of BVI. / Master of Science

In the military arena there is an increase in demand for Low Observable (LO) flight vehicles. This drive for low observability imposes limits on Leading Edge (LE) sweep angles and prohibits the use of a tailplane/fin resulting in unconventional configurations; a typical example of which are Unmanned Combat Aerial Vehicles (UCAVs). This class of aircraft poses stability and control problems due to the early onset of flow separation. The focus of this project is on the on the use of Tangential Leading Edge Blowing (TLEB) as a means of separation suppression on such vehicles. This project is unique in that the TLEB slot is positioned on the wing lower surface facing the oncoming freestream. Also, the model in this project is representative of the outboard panel of a UCAV wing, a geometry on which TLEB has not been explored in the past. A swept wing model (LE sweep = 47 degrees, AR = 3) was designed. The model has a TLEB nozzle with a slot on the lower surface at approx. 1% yawed chord that spans 0.58 m (approx. 70% LE length). Baseline wing characteristics were obtained with the full slot exposed. The wing showed a variation in pitch between CL = 0 and 0.6 which from oil flow visualisation is believed to be due to laminar separation. At CL = 0.6 there is a positive pitch break which flow visualisation suggests is due to the occurrence of a LE vortex. Sensitivity studies for slot configuration, Re number and transition fixing were carried out. The blowing rates 0.0025, 0.005, 0.025, 0.05 were tested for two slot lengths; one full span (0.58 m) and another third span positioned at the midpoint of the full slot. All blowing rates show some suppression of the LE vortex and therefore reduction in severity of the pitch break at CL = 0.6. High blowing rates produce a negative shift in CM, which CFD suggests is due to a large amount of suction produced on the lower wing surface adjacent to the slot exit. This means the available trim power is less than for the lower blowing rates. Wool tuft results for high blowing rates from the middle slot show an increase in streamwise flow at the TE suggesting TLEB is capable of improving the effectiveness of TE devices. The effectiveness of TLEB at low blowing rates has been shown to be high compared to that found in literature. A 1st order analysis of the impact of TLEB on a full scale system shows realistic options.