This work is focused on single phase inverters, which are used for the conversion of the direct current to the alternating current and are nowdays used especially in systems of back-up power supply. The specific aim of this work is implementation of design hight power circuit of inverter include calculation of control algorithm. It describes the complete solution of power circuit. Next step is a analysis of problems concerning the digital control with help of signal processor which is used for solution of regulator structure. Check of the design and checkout of control algorithm is made in the form of simulation in the MATLAB Simulink. Debugged program algorithm is subsequently implemented into the signal microprocessor. The work results rate estimation functionality of inverter and solution of control algorithm.

The aim of my master’s thesis is a system for control of the light intensity. It is electronic equipment which controls the intensity of the light circuits based on settings and input signals. This equipment could work on single-phase systems or multiphase systems. The equipment is controlled by the signal DMX-512 which is a standard for the control of lighting technologies. The set up of this equipment is based on a personal computer or in a limited form by a small connected display.

This diploma thesis deals with adjusting the reverberation time of enclosed spaces. It is divided into two thematic areas. The first thematic area deals with active systems that adjust the reverberation time, with a stronger focus on usage of reverberators to simulate secondary spaces. The second thematic area is the implementation of reverberators and their fundamental building blocks in Matlab.

Thesis describes analog filters topologies with capability of tuning of the main parameters and the MOSFET-C and switched-capacitor filters are described. With focus to linearity and maximal tuning range optimal topology have been chosen. In work the issue of analog switch design is described and is solved. Design of switched-capacitor low-pass Sallen-key filter in Cadence software was made and simulation results are presented.

The dissertation thesis deals with a study of an influence of a simultaneous incidence of an additive thermal noise and a multiplicative phase noise on the useful signal transmission in narrowband satellite communication systems. While the additive thermal noise affects the useful signal only on the receiver side of the communication system, the multiplicative phase noise is produced in all system oscillators. One investigates how the receiver filter bandwidth reduction takes effect on the influence of individual noise types. The thesis is divided into four units. The first one (chapters 4 and 5) solves the ways of modeling of both noise types. In the second part (chapter 6), on the simple example, the primary analysis of the phase noise influence is made. Basic modulation schemes used in the satellite communication are also discussed (chapter 7). Third part (chapter 8) is devoted to the modeling of a general digital system with a M PSK modulation made directly on the main carrier wave. The last part (chapter 9) describes the modeling of a digital system with a BPSK modulation on the auxiliary subcarrier wave followed by an SSB modulation on the main carrier wave. General conclusions are deduced from obtained simulation results.

No description available.

This thesis deals with the synthesis and optimization of frequency analogue filters with modern active elements usable for higher frequencies. The thesis is divided into three parts, the first part deals with the problematic concerning Leap-Frog combined ARC structure. Due to a difficult design, this method is not described in a detail and used in practice, although it shows e.g. low sensitivity. Firstly, a complete analysis of individual filters was made (for and T endings) and consequently these findings were used during implementation of this method to NAF program. Finally, samples of real filters were realized (for verification of functioning and correct design). Another very interesting topic concerning filters is usage of coupled band-pass for small bandwidth, where it is necessary to solve the problems concerning ratio of building elements values, but also price, quality, size of coils, sensitivity, Q factors, coefficients etc. That is why in practice a coil is very often substituted with other equivalent lossy and lossless blocks which create ARC filters structure. The design and the possibility of usage of lossy grounded elements were described here (such as synthetic inductors, frequency dependent negative resistor). Some parts of the design are individual computer sensitivity analysis, setting of usage and quality comparison of individual lossy grounded blocks. Besides, a program for these elements was created, it is useful for a quick design and depiction of transfer characteristics. The third part deals with the usage of tuning universal filters consisting three or more operational amplifiers, which secures its universality and possibility to create different kinds of transfer characteristic. In practice, Akerberg - Mossberg and Kerwin - Huelsman - Newcomb are the most used types of filters. These were also compared with less common universal filters. In the end, the possibility of digital tuning of universal filter with the help of digital potentiometers for filters of 10th order and frequency around 1 MHz was shown.

Diplomová práce obsahuje stručný teoretický základ pro designéra/ku A/D převodníku v technologii CMOS a přehled architektur A/D převodníků používaných v automobilovém průmyslu. Volba vhodné architektury pro konkrétní aplikaci byla zásadním úkolem zpra- covaným v semestrálním projektu předcházejícím tuto práci a je rovněž součástí této práce. Analýza v Matlabu, ze které by mělo vyplynout, je-li třeba zahrnout do architek- tury podblok Sample and Hold, je také součástí práce. Klíčovou částí práce je dokumen- tace návrhu jednotlivých podbloků A/D převodníku – operačního zesilovače, kompará- toru a R-2R D/A převodníku – a ověření jejich funkčnosti. V závěru práce je ověřena funkčnost A/D převodníku jako celku.

Ultraprecision single point diamond turning is required to produce parts with sub-nanometer surface roughness and sub-micrometer surface profiles tolerances. These parts have applications in the optics industry, where tight form accuracy is required while achieving high surface finish quality. Generally, parts can be polished to achieve the desired finish, but then the form accuracy can easily be lost in the process rendering the part unusable. Currently, most mid to low spatial frequency surface finish errors are inspected offline. This is done by physically removing the workpiece from the machining fixture and mounting the part in a laser interferometer. This action introduces errors in itself through minute differences in the support conditions of the over constrained part on a machine as compared to the mounting conditions used for part measurement. Once removed, the fixture induced stresses and the part’s internal residual stresses relax and change the shape of the generally thin parts machined in these applications. Thereby, the offline inspection provides an erroneous description of the performance of the machine. This research explores the use of a single, high resolution, capacitance sensor to quickly and qualitatively measure the low to mid spatial frequencies on the workpiece surface, while it is mounted in a fixture on a standard ultraprecision single point diamond turning machine after a standard facing operation. Following initial testing, a strong qualitative correlation exists between the surface profiling on a standard offline system and this online measuring system. Despite environmental effects and the effects of the machine on the measurement system, the capacitive system with some modifications and awareness of its measurement method is a viable option for measuring mid to low spatial frequencies on a workpiece surface mounted on an ultraprecision machine with a resolution of 1nm with an error band of ±5nm with a 20kHz bandwidth. / Thesis / Master of Applied Science (MASc)