This diploma theses raises the issue of internal tension in two-component outer lense, which are made by injection of polycarbonate. The theses gives a more detail view on treatment of the lenses in heating ovens. Heating ovens have been used for decreasing the internal tension in lenses. The subject of the experiment is to determine the influences of the adjustable parameters of the heating oven. The Experiment will be taken by DoE method. The influence of the adjustable parameters is researched and compared among the two types of outer lense with different type of design.

This diploma thesis submits a proposal of technology design manufacturing threaded plastic ends. In the first part it deals with literary studies of plastics and plastic injection molding. In the second part is the design of an injection form for the specified component. Part of the practical part is also the right choice of material and the injection mold, which was designed based on the calculations of technological parameters. In the conclusion of this thesis is technical economic evaluation.

The meaning of the diploma thesis is to create a new mold plunger for injection mold using a suitable method according to the original mold plunger. The final mold part should meet the required surface parameters. The work is focused on the analysis of the original mold plunger and the experimental verification of suitable methods of production of the equivalent mold plunger.

The aim of the thesis is to determine change of mechanical properties of three types of damp polymeric materials (polyamides) depending on the water content inside material. Before testing, specimens of all three types of materials were placed inside the air conditioning chambers until equilibrium (conditioned) state was reached when the specimens received the maximum possible amount of water from the environment. A total of three conditioning levels were set, representing besides the standard level of conditioning both extreme states like state when the material was fully dried and the state where the material content the largest possible amount of water. With the increasing content of water bound in material, there is a characteristic change in the mechanical properties of the material, such as a decrease in strength and modulus of elasticity and an increase in toughness and ductility. To examine material properties change, tensile and Charpy impact tests were performed, Charpy impact tests were performed for both specimens with and without a notch. Besides changes in mechanical properties, the rate of water absorption was also observed depending on the materials and its filling.

The project elaborated design of optimization venting of molds exhibiting bubbles or low quality weld lines. Based on a literature study of the injection mold venting, the use of vacuum venting, namely the VACUUMJET system of the Spanish CUMSA manufacturer, has been proposed. The experiments proved the elimination of bubbles in the part and the marked improvement of visual quality of the weld lines. The effect on the closing force was not confirmed. The use of the system is more economical for larger batches production, or when high quality parts are required that allow price increasing.

The paper target is design of a conceptual solution of a two-component light-guide with the use of available materials, commonly used for the production of headlamp components, emphasizing the simplicity of the whole solution. The result will be in production of a prototype and the subsequent testing of its functional parameters using standard equipment for the measurement of photometric quantities.

The automotive thermostat currently contributes significantly to the potential to reduce the output of the exhaust gases. The heart of the modern thermostat is the ball valve assembly which also deals with this master‘s thesis. First of all the principles of the quality of the automotive thermostat are described with the choice of further deeper examined properties. The manufacturing process of a ball element and PTFE sealing ring is described. Subsequently the problem of increased production of nonconforming products in production is studied focusing on the surface texture of teflon ring and shape analysis of the ball element. Finally a recommendation for practice with regard to the reduction of additional costs associated with poorly manufactured part is created and further action on this issue is recommended.

The thesis deals with the control of the weight of soft cheeses during molding on a manual line. The theoretical part describes the classification of cheeses into groups, the basic characteristics of soft cheeses and their representatives. Furthemore, the whole technology of soft cheese production is processed and the effects on curd formation and factors influencing the weight of cheeses during molding are explained. The theoretical part ends with the basics of statistics for data processing. Basic measuring techniques (dry matter measurement, pH measurement, measurement of temperature and weight) were selected to determine the technological parameters (pH of whey, pH, dry matter and temperature of cheese grain, weight of cheese etc.) to describe the quality of grain in the experimental part of the thesis. The Design of Experiments method was used to find the optimal setting of the molding machine. Three partial experiments were designed and done. Results were verified in real production. The pH of whey was chosen to describe the grain quality. Two factors have been discovered that have a significant effect on the weigh of cheeses during molding, namely the position of the operator during molding and the amount of whey flowing into the forms with the cheese grain. The proposed molding modifications were successfully tested in production and no statistical difference was found between the weight of cheeses formed with the new setting of molding machine.

The diploma thesis deals with finding suitable process parameters for the production of molding segment by SLM technology. It consists of a combination of structures, shells, thin slats and bulk parts. The tested material is maraging steel 300. The research part deals with the problem of choice of suitable process parameters, such as laser power and speed, hatch distance and thickness of the built layer. The achievable mechanical properties of the parts and the choice of the suitable structure were also examined. In the thesis were found suitable process parameters for printing of bulk parts and structures.

The aim of this thesis is design of technology project for plastic manufacturing. The theoretical part is focused on the characteristics of plastics and plastics production, especially for injection molding of thermoplastics. In the practical part are presented the calculations needed to choice of the injection molding machines and the capacity calculations to determine consumption of granulate and productivity of injection molding machines. Part of this thesis is a list of optimal machinery, including the required peripherals and handling devices complying with the current requirements of a modern plastic manufacturing. The result of this thesis is an economic evaluation of investment costs of machinery for small and medium-sized plastic manufacturing.