A dissertation submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, in fulfilment of the requirements for the degree of Master of Science in Engineering. Johannesburg, 21 July 2016 / The use of supercapacitors for energy storage is an attractive approach considering their ability to deliver high levels of electrical power, unlimited charge/discharge cycles, green environmental protection and long operating lifetimes. Despite the satisfactory power density, supercapacitors are yet to match the energy densities of batteries and fuel cells, reducing the competitiveness as a revolutionary energy storage device. Therefore, the biggest challenge for supercapacitors is the trade-off between energy density and power density. This presents an opportunity to enhance the electrochemical capacitance and mechanical stability of an electrode. Previous attempts to get around the problem include developing porous nanostructured electrodes with extremely large effective areas. One of the emerging high-power supercapacitor electrode materials is molybdenum disulfide (MoS2), a member of the transition-metal dichalcogenides (TMDs). Its higher intrinsic fast ionic conductivity and higher theoretical capacity have attracted a lot of attention, particularly in supercapacitors. In addition to double-layer capacitance, diffusion of the ions into the MoS2 at slow scan rates gives rise to Faradaic capacitance. Analogous to Ru in RuO2, the Mo center atom displays a range of oxidation states from +2 to +6. This plays an important role in enhancing charge storage capabilities. However, the electronic conductivity of MoS2 is still lower compared to graphite, and the specific capacitance of MoS2 is still very limited when used alone for energy storage applications. As evident in several literature reports, there is a need to improve the capacitance of MoS2 with conductive materials such as carbon nanotubes (CNT), polyaniline (PANI), polypyrrole (PPy), and reduced graphene (r-GO). Carbon nanospheres (CNS) have, in the past, improved the conductivity of cathode material in Li-ion batteries, owing to their appealing electrical properties, chemical stability and high surface area. The main objective of this dissertation research is to develop nanocomposite materials based on molybdenum sulphide with carbon nanospheres for pseudocapacitors with simultaneously high power density and energy density at low production cost. The research was carried out in two phases, namely, (i) Symmetric pseudocapacitors based on molybdenum disulfide (MoS2)-modified carbon nanospheres: Correlating physico-chemistry and synergistic interaction on energy storage and (ii) The effects of morphology re-arrangements on the pseudocapacitive properties of mesoporous molybdenum disulfide (MoS2) nanoflakes. The physico-chemical properties of the MoS2 layered materials have been interrogated using the surface area analysis (BET), scanning electron microscopy (SEM), transmission electron microscopy (TEM), x-ray diffraction (XRD), Raman, fourier-transform infrared (FTIR) spectroscopy, and advanced electrochemistry including cyclic voltammetry (CV), galvanostatic cycling with potential limitation (GCPL), repetitive electrochemical cycling tests, and electrochemical impedance spectroscopy (EIS). In the first phase, Molybdenum disulfide-modified carbon nanospheres (MoS2/CNS) with two different morphologies (spherical and flower-like) have been synthesized using hydrothermal techniques and investigated as symmetric pseudocapacitors in aqueous electrolyte. The two different MoS2/CNS layered materials exhibit unique differences in morphology, surface areas, and structural parameters, which have been correlated with their electrochemical capacitive properties. The flower-like morphology (f-MoS2/CNS) shows lattice expansion (XRD), large surface area (BET analysis), and small-sized nanostructures (corroborated by the larger FWHM of the Raman and XRD data). As a contrast to the f-MoS2/CNS, the spherical morphology (s-MoS2/CNS) shows lattice contraction, small surface area with relatively large-sized nanostructures. The presence of CNS on the MoS2 structure leads to slight softening of the characteristic Raman bands (E12g and A1g modes) with larger FWHM. The MoS2 and its CNS-based composites have been tested in symmetric electrochemical capacitors in aqueous 1 M Na2SO4 solution. CNS improves the conductivity of the MoS2 and synergistically enhanced the electrochemical capacitive properties of the materials, especially the f-MoS2/CNS-based symmetric cells (most notably, in terms of capacitance retention). The maximum specific capacitance for f-MoS2/CNS-based pseudocapacitor show a maximum capacitance of 231 F g-1 with high energy density 26 Wh kg-1 and power density 6443 W kg-1. For the s-MoS2/CNS-based pseudocapcitor, the equivalent values are 108 F g-1, 7.4 Wh kg-1 and 3700 W kg-1. The high-performance of the f-MoS2/CNS is consistent with its physico-chemical properties as determined by the spectroscopic and microscopic data. In the second phase, Mesoporous molybdenum disulfide (MoS2) with different morphologies has been prepared via a hydrothermal method using different solvents, water or water/acetone mixtures. The MoS2 obtained with water alone gave graphene-like nanoflakes (g-MoS2) while the other with water/acetone (1:1 ratio) gave a hollow-like morphology (h-MoS2). Both materials are modified with carbon nanospheres as conductive materials and investigated as symmetric pseudocapacitors in aqueous electrolyte (1 M Na2SO4 solution). Interestingly, a simple change of synthesis solvents confers on the MoS2 materials different morphologies, surface areas, and structural parameters, correlated by electrochemical capacitive properties. The g-MoS2 exhibits higher surface area, higher capacitance parameters (specific capacitance of 183 F g-1, maximum energy density of 9.2 Wh kg-1 and power density of 2.9 kW kg-1) but less stable electrochemical cycling compared to the h-MoS2. These findings have opened doors for further exploration of the synergistic effects between MoS2 graphene-like sheets and CNS for energy storage. / MT2017

No description available.

No description available.

No description available.

Hydrolysis of cellulosic biomass is an important and ongoing subject of research due to generating precursors for biofuel synthesis. This work involves hydrolysis of microcrystalline cellulose and Arundo donax to glucose. Methods for acid hydrolysis include the use of sulfuric acid, phosphomolybdic acid, blue molybdenum using low concentrations at 40-100 °C. For comparison purposes, enzymatic hydrolysis was also carried out using cellulase. Products were quantified by measuring total organic carbon and reducible sugars using dinitrosalicylic acid. Use of phosphomolybdic acid, blue molybdenum and sulfuric acid even at 6.0 M did not increase the amount of glucose compared to using water only. Interestingly, enzymatic hydrolysis of powdered Arundo donax without pretreatment was successful and resulted in statistically similar amounts of glucose compared to using microcrystalline cellulose. Efforts are ongoing to understand the enzyme kinetics in the hydrolysis of Arundo donax and potentially increase the yield of glucose using chemical and microbiological pretreatment.

Many organometallic reactions are solvent-dependent, suggesting solvent molecules interact with reaction intermediates. Studies of the solvent exchange reaction of group 6 transition metal carbonyls with moderately binding ligands have provided insight into these interactions, however, studies of the mechanism for this reaction with weakly binding ligands have not been performed. Experiments were conducted on the nanosecond time scale in methylcyclohexane over the temperature range of 4 to 44 °C using Step Scan FTIR (SS FTIR) spectroscopy with weakly binding ligands benzene and mesitylene. Upon photolysis of the metal hexacarbonyls, the kinetically favored product (M(CO)5(solv)), decays following pseudo-first-order kinetics to the thermodynamical favored product, M(CO)5(L). The decay is fit using a single exponential decay with a single exponential instrument response function, time zero and an offset. An Arrhenius plot yielded activation energies of 23.7 kJ/mol (M = Mo, L = benzene), 35.1 kJ/mol (M = W, L = benzene) and 29.8 kJ/mol (M = Mo, L = mesitylene). DFT calculations using NWCHEM gave binding energies of 45.8 and 54.3 kJ mol-1 for Mo(CO)5C6H12 and W(CO)5C6H12. The experimental and computational results suggest the exchange mechanism proceeds through an associative pathway, were slightly negative values of the entropy of reaction denote that the transition state has greater metal solvent bond breaking character then the more moderately binding ligands in the literature. Density Functional theory was used to calculate C-O vibrational frequencies of metal carbonyl complexes measured in our work and other complexes from the literature, with density functionals B3LYP, M06 and M06-L. Measured and computational frequencies were compared to obtain both an overall vibrational shift and a scaling factor. Scaling factors were found to be 0.9519±0.0095 for B3LYP, 0.9429 ± 0.0087 for M06 and 0.9565 ± 0.0095 for M06-L with overall shifts of 102 ± 16, 121 ± 15, 93 ± 17 cm-1, respectively. The molybdenum mediated Pauson-Khand reaction, a [2+2+1] cyclo-addition begins very similarly to the solvent exchange reaction on molybdenum. The initial product, the solvated complex, decays away with pseudo-first-order kinetics as the solvent is replaced by the C-C triple bond in 2-(2-propen-1-yl)-2-(2-propyn-1-yl)-,1,3-diethyl ester. An Arrhenius plot over the temperature range of -8 to 20° C yielded an energy of activation of 15.6 kJ/mol.

Hydrogen is a clean and sustainable form of carrier of energy that can be used in mobile and stationary applications. At present hydrogen is produced mostly from fossil sources. Solar photoelectrochemical processes are being developed for hydrogen production. Storing hydrogen can be done in three main ways: in compressed form, liquid form and by chemical bonding. Near term spaceport operations are one of the prominent applications for usage of large quantities of liquid hydrogen as a cryogenic propellant. Efficient storage and transfer of liquid hydrogen is essential for reducing the launch costs. A Two Stage Reverse Turbo Brayton Cycle (RTBC) CryoCooler is being developed at University of Central Florida. The cryocooler will be used for storage and transport of hydrogen in spaceport and space vehicle application. One part in development of the cryocooler is to reduce the friction and wear between mating parts thus increasing its efficiency. Tribological coatings having extremely high hardness, ultra-low coefficient of friction, and high durability at temperatures lower than 60 K are being developed to reduce friction and wear between the mating parts of the cryocooler thus improving its efficiency. Nitrides of high-melting-point metals (e.g. TiN, ZrN) and diamond-like-carbon (DLC) are potential candidates for cryogenic applications as these coatings have shown good friction behavior and wear resistance at cryogenic temperatures. These coatings are known to have coefficient of friction less than 0.1 at room temperature. However, cryogenic environment leads to increase in the coefficient of friction. It is expected that a composite consisting of a base layer of a hard coating covered with layer having an ultra-low coefficient of friction would provide better performance. Extremely hard and extremely low friction coatings of titanium nitride, molybdenum disulphide, TiN/MoS2 bilayer coatings, DLC and DLC/MoS2 bilayer coatings have been chosen for this application. TiN film was deposited by reactive DC magnetron sputtering system from a titanium target and MoS2 film was deposited by RF magnetron sputtering using a MoS2 target. Microwave assisted chemical vapor deposition (MWCVD) technique was used for preparation of DLC coatings. These composite coatings contain a solid lubricating phase and a hard ceramic matrix phase as distinctly segregated phases. These are envisioned as having the desired combination of lubricity and structural integrity. Extremely hard coatings of TiN and DLC were chosen to provide good wear resistance and MoS2 was chosen as the lubricating phase as it provides excellent solid lubricating properties due to its lamellar crystal structure. This thesis presents preparation; characterization (SEM and XRD), microhardness and tribological measurements carried out on TiN and TiN/MoS2 coatings on aluminum and glass substrate at room temperature. It also presents initial development in preparation of DLC coatings.

http://purl.fcla.edu/fcla/etd/CFE0003747

The interaction of the 2,3-diazanaphthalene, phthalazine and its 1-substituted derivatives with the molybdenum hydroxylases, aldehyde oxidase and xanthine oxidase, has been investigated both in vivo and /Ok in vitro. Metabolic studies, carried out by treating rabbits with both cold and 14C-labelled phthalazine, have shown that this compound is extensively metabolised in vivo, the major metabolite being a glucuronide conjugate. Very little unchanged phthalazine or its molybdenum hydroxylase mediated oxidation product 1-hydroxyphthalazine were excreted in the urine. Pretreatment of rabbits with phthalazine or 1-hydroxyphthalazine had no effect upon the activity of the microsomal monooxygenases but caused a significant increase in the specific activities of both aldehyde oxidase and xanthine oxidase. Determination of the molybdenum content of purified aldehyde oxidase fractions using electrothermal atomic absorption spectroscopy has confirmed that an increase in the molybdenum content of the enzyme fraction accompanies the increase in activity. A qualitative assessment of purified aldehyde oxidase fractions using iso-electric focusing has indicated that this enzyme may be composed of 2 or 3 active variants and following pretreatment with either phthalazine or 1-hydroxyphthalazine a further band of enzyme activity is apparent on the electropherogram. The Km value for phthalazine is significantly reduced with enzyme prepared from phthalazine treated rabbits, indicating that a form of the enzyme with a high affinity for phthalazine may have been induced. 1-Hydrazinophthalazine (Hydralazine) and two other hydrazine substituted N-heterocycles, endralazine and 1-hydrazinoisoquinoline have been shown to exert a potent progressive inhibition of aldehyde oxidase in vitro, effective only in the presence of substrate, but are inactive towards xanthine oxidase. In addition, administration of hydralazine to rabbits results in a significant reduction in liver aldehyde oxidase activity. Investigations into the interaction of some of the metabolites of hydralazine with aldehyde oxidase in vitro suggest that hydralazine is also the inhibiting species in vivo. / The Ransom Fellowship awarded by The Pharmaceutical Society of Great Britain,

No description available.