Atherosclerotic plaques in the bifurcation of the carotid artery vessels can pose a significant stroke risk from stenosis, thrombosis and emboli, or plaque rupture. However, the possibility of the latter depends on the structure of the plaque and its stability. So far, the assessment of such depositions, and the evaluation of the risk they pose, is not satisfactory with 3 Tesla black blood imaging. It is expected that the SNR increase at 7 Tesla, together with an appropriate and patient-safe RF coil, will result in higher resolution images that would help in better assessing the composition of atherosclerotic plaques in vessel walls. A custom-built neck array was designed and constructed, with the aim of investigating the benefits of the higher field strength using DANTE-prepared black blood imaging. A 4-channel transmit array was designed to generate the required <b>B</b>^&plus;<sub style='position: relative; left: -.5em;'>1</sub> field for the DANTE module to be used. A separate close fitting 4-channel receive array was preferred for improved SNR and parallel (receive) imaging. Geometric, active, passive as well as preamp decoupling schemes were employed for adequate isolation between the arrays and their channels. Electromagnetic simulation software, Semcad X (SPEAG, Zurich), was used for safety assessment with human phantoms (Virtual population). The <b>E</b> fields for 1 W transmission per channel were calculated for each element for a worst case SAR estimation. The transmission power limits per channel were set according to the 10g SAR limit set in IEC 60601. For simulation validation, temperature measurements and surface heat mapping were performed on a meat phantom. Finally, a healthy male subject was scanned using a protocol consisting of <b>B</b>₁ mapping, RF shimming at an ROI, and 2D and 3D DANTE prepared Gradient Echo (GRE). The worst-case heating scenario, as defined in the methods section, generated a maximum local SAR of 7.65 W/kg for 1 Watt per channel input. Thus, for 1st level mode (20W/kg max), the power limit was set at 2.6 W per channel. The heating profile was similar to that simulated and the measured temperature increase was within a &plusmn;10&percnt; margin relative to the simulation. The global SAR power limit per channel was found to be higher (i.e. more allowed power) than the worst case local SAR power limit, and thus did not impose additional power penalty. The resolution achieved was 0.6 mm isotropic for the 3D protocol and 0.6 by 0.6 by 2.5 mm for the 2D protocol. The average SNR was measured within the vessel wall location of the two carotid arteries and found to be 27&plusmn;6 for the DANTE images and for the static tissue closer to the skin the SNR was 55&plusmn;2. In conclusion, a 4Tx/4Rx coil was designed to target the carotid arteries operating under pTx mode and a black blood imaging sequence was implemented for blood signal suppression and vessel wall imaging. The initial results from the subject and phantom imaging show satisfactory blood suppression and spatial resolution.

Computed Tomography (CT) is often used for building 3D biomechanical models of human anatomy. This method exposes the subject to a significant x-ray dose and provides limited soft-tissue contrast. Magnetic Resonance Imaging (MRI) is a potential alternative to CT for this application, as MRI offers significantly better soft-tissue contrast and does not expose the subject to ionizing radiation. However, MRI requires long scan times to achieve 3D images at sufficient resolution, signal-to-noise ratio (SNR), and contrast-to-noise ratio (CNR). These long scan times can make subject motion a problem. This thesis describes my work to reduce scan time while achieving sufficient resolution, SNR, and CNR for 3D biomechanical modeling of (1) the human larynx, and (2) the human hip. I focused on two important strategies for reducing scan time and improving SNR and CNR: the design of RF coils optimized to detect MRI signals from the anatomy of interest, and the determination of MRI relaxation properties of the tissues being imaged (allowing optimization of imaging parameters to improve CNR between tissues). Work on the larynx was done in collaboration with the Thomson group in Mechanical Engineering at BYU. To produce a high-resolution 3D image of the larynx, a 2-channel phased array was constructed. Eight different coil element designs were analyzed for use in the array, and one chosen that provided the highest Q-ratio while still meeting the mechanical constraints of the problem. The phased array was tested by imaging a pig larynx, a good substitute for the human larynx. Excellent image quality was achieved and MR relaxometry was then performed on tissues in the larynx. The work on the hip was done in collaboration with the Anderson group in orthopedics at the University of Utah, who are building models of femoral acetabular impingement (FAI). Accurate imaging of hip cartilage requires injection of fluid into the hip joint capsule while in traction. To optimize contrast, MR relaxometry measurements were performed on saline, isovue, and lidocaine solutions (all typically injected into the hip). Our analysis showed that these substances actually should not be used for MR imaging of the hip, and alternate strategies should be explored as a result.