Part I discusses the development of an aluminum-magnesium-silicon alloy that may combine strength, extrudability, favorable corrosion resistance with low cost and scrap compatibility. The first part of the study determined the effects of small composition, heat treatment and mechanical processing changes on the ambient temperature tensile properties of the alloy. A combination of magnesium and silicon of about 2%, 1% copper, 0.2% chromium and 0.1% vanadium can produce a T6 alloy with significant higher strength, fatigue and corrosion fatigue properties for both ingot and extrusion than those of 6061 but with only a modest increase in cost. The new alloy has been designated as AA6069. The second part of the study determined the T6 properties of 6069 alloy. The tensile test results of cold and hot extrusions of hollow, solid bars, and high pressure cylinders indicate that the T6 properties ranged from 55-70 ksi (380-490 MPa) UTS, 50-65 ksi (345-450 MPa) yield strength, and 10-18% elongation. It also appears that the fracture toughness and general corrosion resistance in saline environment are comparable or better than those of 6061 T6. Part II attempted to evaluate the formation, formability, thermal and mechanical properties of semi-solid A356, A357 and modified aluminum silicon semi-solid alloys. The semi-solid alloy microstructure was produced in this study by purely thermal treatment rather than conventional and expensive electromagnetic or mechanical stirring. Three heat-up stages in semi-solid treatment were evaluated. Stage I is related to the heating of the alloy in the solid state. Stage II is related to the eutectic reaction. Stage III is related to the heating of the semi-solid slurry. Stage II requires the longest time of the three heat-up stages due to the endothermic reaction on heating. An increase of furnace temperature can greatly reduce the time of stage II. The atmosphere (vacuum, air, argon) of the semi-solid treatment does not appear to greatly affect the T6 properties of semi-solid alloys. The microstructure and T6 properties of semi-solid A356 do not appear sensitive to the homogenization treatments before semi-solid treatment. The porosity of semi-solid ingots and pressed parts increases as the cooling rate decreases in unformed and subsequent-to-moderate pressure forming. The T6 properties basically appear sensitive to voids, with a degradation of properties as the void concentration increases. The formability of A357 may be improved as the spheroidal particle size decreases. Hence, formability may improve with decreasing ingot grain size. The mechanism of coarsening of the solid phase at isothermal temperatures is related to Ostwald ripening and/or "merging" of particles. The mechanical properties of die-casting parts show that the method of thermal treatment to produce a spheroidal microstructure is an effective method for industrial production of semi-solid aluminum-silicon alloys. / Graduation date: 1997

Thesis (M. Eng. Sc.)--University of Adelaide, Dept. of Chemical Engineering,1991. / Includes bibliographical references (leaf 95).

No description available.

No description available.

Equilibrium properties of the MgO-Al₂O₃-SiO₂ (MAS) system are modeled using techniques from statistical and quantum mechanics. The fundamental structural units in this model are the closed shell ions: Mg²⁺, Al³⁺, Si⁴⁺, and O²⁻. The equilibrium properties of the MAS system are determined by the interactions among these ions and by the environment (i.e. temperature and pressure). The interactions are modeled using coulombic, dispersion, and repulsive forces. Two parameters appearing in the repulsive terms for each cation-oxygen interaction are fitted from properties of quartz, corundum, and periclase crystals. The effects of the environment on the liquid and solid compositions found in this system are calculated using a Monte Carlo technique involving the generation of a Markov chain of configurations; each configuration being a "snapshot" of the particles in the liquid or solid material being studied. The properties of the material are derived from averaging appropriate quantities over all the configurations. Enthalpies of formation, heat capacities, and volumes of seven compositions in the MAS system have been calculated using this method. All are within three percent of the corresponding experimental values. Radial distribution functions for these runs show the competition among the cations for the common anion, oxygen, under charge and mass balance constraints. The electronic structure of several molecular clusters in the MAS system are examined using ab initio linear combinations of atomic orbitals (LCAO) techniques. The assumptions used in LCAO calculations are examined and a small, balanced basis set for the MAS system is presented. The Mg-, Al-, and Si-O interactions are all found to be highly ionic using this basic set. Using a first principles technique, the two body effective pair potentials assumed for the Monte Carlo calculations were shown to be physically reasonable.

Cast Al-Si and Al-Si-Mg alloys containing up to 12.6 wt. pct. silicon and 1.0 wt. pct. magnesium were prepared. The changes in electrical conductivity/resistivity of these alloys due to strontium additions have been investigated and explained in terms of variations in microstructure. The conductivity behaviour of strontium-containing and strontium-free alloys was found to exhibit marked differences, depending on the silicon and magnesium contents and the rate of solidification. The electrical conductivity of single phase alloys containing less than 1.60 wt. pct. Si decreased with increasing silicon and magnesium levels. However, strontium had no effect on the conductivity of these solid solution alloys since it does not dissolve appreciably in the aluminum matrix or change the solid solubility of silicon and magnesium in aluminum. Silicon precipitation processes in the supersaturated solid solution alloys of Al-Si and Al-Si-Sr have been examined using the Johnson-Mehl-Avrami equation and found to be isokinetic. Strontium, however, retarded the growth rate of silicon precipitates. Strontium did not affect the kinetics of G.P. zone formation in Al-Si-Mg alloys but it suppressed the formation of stable Mg$ sb2$Si precipitates during subsequent aging at 175$ sp circ$C. Unlike the single phase alloys, two phase Al-Si and Al-Si-Sr alloys, in the range of 2.0 to 12.6 wt. pct. Si, exhibited different electrical conductivity behaviour. The strontium-containing alloys showed a higher conductivity than alloys with no strontium, and this conductivity difference increased as the silicon and magnesium contents were increased and the solidification rate was decreased. It has been demonstrated this difference is due to changes in the silicon morphology. Electron scattering at the interface between the aluminum matrix and the eutectic silicon phase contributes significantly more to the resistivity of unmodified alloys than that of modified alloys. In addition, the resistivity of

No description available.

No description available.

Mémoire (M.Eng.)-- Université du Québec à Chicoutimi, 1994. / Résumé disponible sur Internet. CaQCU Document électronique également accessible en format PDF. CaQCU

Thèse (M.Eng.) -- Université du Québec à Chicoutimi, 2005. / Bibliogr.: f[160]-167. Document électronique également accessible en format PDF. CaQCU