Spelling suggestions: "subject:"amagnetic circuit aptimization"" "subject:"amagnetic circuit foptimization""
1 |
Design of a magnetorheological brake system based on magnetic circuit optimizationKarakoc, Kerem 21 August 2007 (has links)
Conventional hydraulic brake (CHB) systems used in automotive industry have several limitations and disadvantages such as the response delay, wear of braking pad, requirement for auxiliary components (e.g. hydraulic pump, transfer pipes and brake fluid reservoir) and increased overall weight due to the auxiliary components. In this thesis, the development of a novel electromechanical brake (EMB) for automotive applications is presented. Such brake employs mechanical components as well as electrical components, resulting in more reliable and faster braking actuation. The proposed electromagnetic brake is a magnetorheological (MR) brake.
The MR brake consists of multiple rotating disks immersed into an MR fluid and an enclosed electromagnet. When current is applied to the electromagnet coil, the MR fluid solidifies as its yield stress varies as a function of the magnetic field applied by the electromagnet. This controllable yield stress produces shear friction on the rotating disks, generating the braking torque. This type of braking system has the following advantages: faster response, easy implementation of a new controller or existing controllers (e.g. ABS, VSC, EPB, etc.), less maintenance requirements since there is no material wear and lighter overall weight since it does not require the auxiliary components used in CHBs.
The MRB design process included several critical design steps such as the magnetic circuit design and material selection as well as other practical considerations such as cooling and sealing. A basic MRB configuration was selected among possible candidates and a detailed design was obtained according to a set of design criteria. Then, with the help of a finite element model (FEM) of the MRB design, the magnetic field intensity distribution within the brake was simulated and the results were used to calculate the braking torque generation.
In order to obtain an optimal MRB design with higher braking torque generation capacity and lower weight, the key design parameters were optimized. The optimization procedure also consisted of the FEM, which was required to calculate the braking torque generation in each iteration. Two different optimization search methods were used in obtaining the minimum weight and maximum braking torque: (i) a random search algorithm, simulated annealing, was first used to find an approximate optimum design and (ii) a gradient based algorithm, sequential quadratic programming, was subsequently used to obtain the optimum dimensional design parameters.
Next, the optimum MRB was prototyped. The braking performance of the prototype was tested and verified, and the experimental results were shown. Also, experimental results were compared with the simulation results. Due to the lack of accurate material property data used in the simulations, there were discrepancies between the experimental and the simulation results.
Other possible sources of errors are also discussed. Since the prototype MRB generates much lower braking torque compared to that of a similar size CHB, possible design improvements are suggested ton further increase the braking torque capacity. These include the relaxation of the optimization constraints, introduction of additional disks, and the change in the basic magnetic circuit configuration.
|
2 |
Optimalizace magnetického obvodu klasického asynchronního motoru při napájecí frekvenci do 210 Hz / Optimization of magnetic circuit of induction motor for frequency up to 210 HzBinek, Martin January 2019 (has links)
This master’s thesis first deals with the theory concerning induction motor. It briefly desbribes the construction of three-phase induction motors, the generation of tractive force, power flow with loss distribution and also torque characteristic. In the next part an analytical calculation of the parameters of equivalent circuit for an existing induction motor with known dimensions is performed. After the calculation it is possible to find out the rated parameters of the motor, which makes it possible to further compare results with the values obtained by other methods. The next step was to create a model of the motor in RMxprt program, which is later also translated to ANSYS Maxwell 2D model. Simulations were carried out in both interfaces. As the next step the results obtained by the three methods are compared with measured values and also evaluated. The final part of the thesis focuses on the optimization of the magnetic circuit for higher frequencies. Efficiency of the modified induction motor is examined for higher frequencies using RMxprt Optimetrics and this procedure is performed for both default and alternative electrical steel materials.
|
Page generated in 0.0746 seconds