No description available.

This work studies guided wave propagation in pipes coated with thick highly viscoelastic coating materials. The main motivation for this study is the problems associated with Long Range Ultrasonic Testing (LRUT) of coated pipelines. The results reported in the literature show that the proper determination of the optimum LRUT parameters depends strongly on the bulk acoustic properties of the coating materials. The bulk acoustic properties of coating materials reported in the literature show that they could vary significantly depending on the coating material age, temperature and bonding level. The methods for acoustic characterisation of coating materials reported by other researchers, have been studied and it was found that they do not take into account the temperature changes and bonding level variation. In this work, the bulk acoustic properties of two highly viscoelastic bitumen based coating materials are investigated. The conventional methods for acoustic characterisation are studied and a new method for independent measurement of bulk shear properties of bitumen is developed. The bulk acoustic properties of bitumen based coating materials are also studied by two new characterisation methods. The first method derives the bulk coating material properties from experimental data on guided wave reflection coefficients. The second method derives the coating material bulk properties from experimentally measured guided wave attenuation data. It is demonstrated that these new methods deliver much more accurate values for the bulk acoustic properties when compared to the data measured by conventional methods. The second method is used to study the temperature effect on the bulk acoustic properties and it is demonstrated that temperature has a significant effect. The validity of the acoustic properties for the two bitumen materials is investigated through comparison between numerical predictions and experimental data measured for guided wave reflection coefficients and attenuation of the torsional T(0,1) and longitudinal L(0,2) guided wave modes. Good agreement is achieved in the frequency range between 20 kHz and 100 kHz, which is typical for LRUT of pipes.

Degenerative disorders of the rotator cuff tendons account for nearly 75% of all shoulder pain, causing considerable pain and morbidity. Given the strong correlation between age and tendinopathy, and unprecedented population aging, these disorders will become increasingly prevalent. Improved understanding of tendon degeneration will guide the development of future diagnostic and treatments, and is therefore urgently needed. However, the aetiology and pathology of rotator cuff tendinopathy remain unclear. The complicated mechanical environment of the rotator cuff is hypothesised to influence the susceptibility of the tendons to degeneration and tearing. Studies have reported biological adaptations in torn cuff tendons indicative of increased compressive loading within the tendon. The material adaptations of healthy and degenerative cuff tendons are largely unreported but will provide further insight into the role of the mechanical environment in rotator cuff aetiology and pathology. This thesis examined the material adaptations of healthy and diseased tendons to explore the role of mechanical loading in rotator cuff pathology. The material adaptations of healthy animal tendons, and healthy and delaminated human cadaveric rotator cuff tendons, in response to different loading environments were characterised. The effects of age, tears, steroid injection and subacromial decompression surgery on the structural adaptations of human cuff tendons were also studied, as was the effect of tendon cell proliferation on the mechanical properties and degradation behaviour of collagen scaffolds. Loading environment significantly affected the structural adaptations of healthy tendons. Regions exposed to compressive and shear strains exhibited thinner fibres, shorter crimp lengths and thinner, less aligned fibrils compared with regions exposed to tensile strains alone. In healthy rotator cuff tendons, the inhomogeneous loading environment produced topographically inhomogeneous structural adaptations. The tendons of a delaminated rotator cuff exhibited less topographical variation in properties and thinner, less aligned fibrils compared with healthy cuff tendons. Torn cuff tendons exhibited thinner fibrils and shorter crimp lengths compared with control samples. These adaptations were identifiable early in the disease progression, and neither steroid injection nor subacromial decompression surgery significantly influenced these adaptations at seven weeks post‐treatment. Significant correlations between decreasing dimensions and increasing tear size were found when age was included as a confounding factor, reflecting the importance of age and tear size in determining the material properties of tendons. Tendon cell proliferation influenced the mechanical properties and degradation behaviour of the collagen scaffolds, emphasising the integral role of cells in the functional adaptation of biological materials. These results demonstrate the effect of mechanical environment on the material adaptations of tendons. They also indicate the importance of the complicated mechanical environment experienced by the rotator cuff tendons in predisposing the tendons to degeneration and tearing. The observed material adaptations of degenerative and torn tendons suggest that rotator cuff pathology is associated with increased levels of compressive and/or shear strains within the tendon. These changes begin early in the disease progression and neither steroid injection nor sub‐acromial decompression surgery are capable of reversing the changes in the timeframe investigated. These findings highlight the urgent clinical need for pre‐rupture diagnostic techniques for the detection of early pathological changes in the rotator cuff. They also emphasize the requirement for new intervention strategies that restore the healthy mechanical environment and reverse early pathological adaptations in order to prevent catastrophic failure of the tendons.

In the drive towards higher strength alloys, a diverse range of alloying elements is employed to enhance their strength and ductility. Limited solid solubility of these elements in steel leads to segregation during casting which affects the entire down-stream processing and eventually the mechanical properties of the finished product. The work presented in this PhD shows that segregation of alloying elements during casting, particularly aluminium, leads directly to banding in the final product. It has been demonstrated that no significant homogenisation is possible in this alloy within practical time constraints of the industrial thermo-mechanical process. A through-process model was developed to design a thermo-mechanical treatment aimed at reducing the effects of segregation on the formation of banding. A new polynomial function for calculating the local phase transformation temperature (Ae3) between the austenite + ferrite and the fully austenitic phase fields during heating and cooling of steel is presented. Material was produced both with and without banding and used to study the effect upon the mechanical properties. The banded steel variants show a significant reduction in tensile strength for a similar level of ductility compared to non-banded variants. In situ measurement under uniaxial loading using high-energy synchrotron diffraction allowed direct quantification of the impact of the mechanically induced transformation of metastable austenite on the work- hardening behaviour. The results reveal that the mechanically induced transformation of austenite does not begin until the onset of matrix yielding and the experimental evidence demonstrates that the austenite to martensite transformation increases the work-hardening rate of the ferrite phase and delays the onset of Stage-III hardening until the yield point of austenite. The increase in work-hardening rate (and thus work required) supports a driving force approach to transformation induced plasticity. The transformation work required leads to an increase in the macroscopic work-hardening rate after matrix yielding which offsets the decrease in the work-hardening rate in the ferrite and martensite phases up to the UTS. Steels with a high degree of banding do not show this extra contribution due to the more dominant anisotropic effect of martensite bands on the work-hardening of ferrite coupled to increased mechanical austenite stability as a result of increased carbon content. A list of revisions as requested by the examiners is produced on pages 18 and 19 of the thesis for examination. Abstract: In the drive towards higher strength alloys, a diverse range of alloying elements is employed to enhance their strength and ductility. Limited solid solubility of these elements in steel leads to segregation during casting which affects the entire down-stream processing and eventually the mechanical properties of the finished product. The work presented in this PhD shows that segregation of alloying elements during casting, particularly aluminium, leads directly to banding in the final product. It has been demonstrated that no significant homogenisation is possible in this alloy within practical time constraints of the industrial thermo-mechanical process. A through-process model was developed to design a thermo-mechanical treatment aimed at reducing the effects of segregation on the formation of banding. A new polynomial function for calculating the local phase transformation temperature (Ae3) between the austenite + ferrite and the fully austenitic phase fields during heating and cooling of steel is presented. Material was produced both with and without banding and used to study the effect upon the mechanical properties. The banded steel variants show a significant reduction in tensile strength for a similar level of ductility compared to non-banded variants. In situ measurement under uniaxial loading using high-energy synchrotron diffraction allowed direct quantification of the impact of the mechanically induced transformation of metastable austenite on the work- hardening behaviour. The results reveal that the mechanically induced transformation of austenite does not begin until the onset of matrix yielding and the experimental evidence demonstrates that the austenite to martensite transformation increases the work-hardening rate of the ferrite phase and delays the onset of Stage-III hardening until the yield point of austenite. The increase in work-hardening rate (and thus work required) supports a driving force approach to transformation induced plasticity. The transformation work required leads to an increase in the macroscopic work-hardening rate after matrix yielding which offsets the decrease in the work-hardening rate in the ferrite and martensite phases up to the UTS. Steels with a high degree of banding do not show this extra contribution due to the more dominant anisotropic effect of martensite bands on the work-hardening of ferrite coupled to increased mechanical austenite stability as a result of increased carbon content.