In striving to produce high quality cast components from recycled aluminium alloys,imperfections have to be considered, because recycled aluminium usually containsmore of it. However, there are great energy savings to be made by using recycledaluminium; as little as 5% of the energy needed for primary aluminium productionmay be required. High quality castings are dependent on, besides alloy chemistry, bothmelt quality and the casting process; the focus of this work is related to the meltquality.This thesis aims to increase knowledge about imperfections, foremost about Fe-richparticles, oxides/bifilms, and porosity. Experiments were performed at industrialfoundry facilities and in a laboratory environment. Melt quality was evaluated byproducing samples with the reduced pressure test (RPT), from which both densityindex (DI) and bifilm index (BI) could be measured, results that were related to tensiletest properties. Data from tensile test samples were analysed, and fracture surfacesand cross sections were studied in both light microscope and in scanning electronmicroscope (SEM). For the purpose of investigating nucleation of primary Fe-richparticles (sludge) differential scanning calorimetry (DSC) was used.In the analysis of results, a correlation between the morphology of particles and tensileproperties were found. And elongated Fe-rich β-particles were seen to fracturethrough cleavage towards the centre. However, DI and BI have not been possible torelate to tensile properties.The nucleation temperature of primary Fe-rich particles were found to increase withincreased Fe, Mn, and Cr contents, i.e. the sludge factor (SF), regardless of cooling rate.For a set SF, an increase of cooling rate will decrease the nucleation temperature.

The use of aluminum is a key factor in creating an Eco-friendlier automotive industry. The material has good properties and the ability to reuse the material. The requirement on the material in this industry is very high, due to the exposed working environments. The usage of aluminum will reduce the vehicle’s weight, which in turn will reduce emissions.    Aluminum casting is not free from obstacles. The properties can be altered with different casting methods and the design of the casting to a great extent. This master will focus on how the melt quality will have an impact on the material properties and how it is changed during the process. To fully understand what happens to the melt during the casting process, samples are received at different stages for further investigation. Different data is collected to be able to analyze what happens during the process. A quality measurement called the Quality index is used to determine the change in the quality in the different stages. With data from bifilm and density index, conclusions can be made on how and where the impurities are entering the melt and their effect. A conclusion is made that the degassing harms the quality of the melt.

The need to produce lighter components due to environmental aspects and the development of electrical vehicles represents an opportunity for cast aluminium-silicon alloys. With high specific strength, good castability, high corrosion resistance and recyclability, these alloys offer an attractive combination of properties as an alternative to steel, cast iron and titanium-based components in certain applications. To take advantage of such a combination of properties, there is a need to ensure that they can be reliably achieved. In other words, high performing components need to be produced. For that, the production cycle, from alloy selection and melt preparation, to the casting and heat treatment of the component must be understood and controlled as a whole. The different steps in the production cycle will affect the microstructure of the components and hence the resulting mechanical properties. Understanding the relation between the different steps in the production cycle, its consequences on the microstructural features and on the mechanical properties constitutes the aim of this thesis. Experiments applying state-of-the-art knowledge regarding effect of casting process, alloying system and post-process variables were performed aimed at achieving properties similar to those of high pressure die casting (HPDC) components. Different melt quality determination tools were evaluated on three different EN AC-46000 melt qualities. The influence of modification, grain refinement and both treatments together was assessed on an Al-10Si alloy solidified under different cooling rates. The tensile behaviour and the impact of features such as secondary dendrite arm spacing (SDAS) or grain sizes was quantified. It was corroborated that by appropriate selection and control of such alloying system, process and post-process variables it is possible to achieve HPDC EN AC-46000 tensile and fatigue properties through a T5 treated sand cast EN AC-42100 alloy. On the other hand, the available techniques for melt quality assessment are inadequate, requiring further analysis to successfully identify the melt quality. Additionally, it was observed that decreasing the melt quality by additions of 25 wt.% of machining chips did not significantly decrease the tensile properties but slightly increased the variation in them. In relation to the modification and grain refinement of Al-10Si alloys it was concluded that with the slowest cooling rate tested, additions of only grain refiner did not successfully produce equiaxed grains. For cooling rates corresponding to dendrite arm spacings of 15 μm and slower, combined additions of grain refiner and modifier can lead to higher tensile properties compared to the corresponding separate additions. SDAS was observed to describe flow stress through the Hall-Petch equation but grain size did not show a physically meaningful relationship. Furthermore, beginning of cracking was detected in the plastic deformation region at dendrite/eutectic boundaries and propagated in a trans-granular fashion.

Yes / Polymer extrusion, in which a polymer is melted and conveyed to a mould or die, forms the basis of most polymer processing techniques. Extruders frequently run at non-optimised conditions and can account for 15-20% of overall process energy losses. In times of increasing energy efficiency such losses are a major concern for the industry. Product quality, which depends on the homogeneity and stability of the melt flow which in turn depends on melt temperature and screw speed, is also an issue of concern of processors. Gear pumps can be used to improve the stability of the production line, but the cost is usually high. Likewise it is possible to introduce energy meters but they also add to the capital cost of the machine. Advanced control incorporating soft sensing capabilities offers opportunities to this industry to improve both quality and energy efficiency. Due to strong correlations between the critical variables, such as the melt temperature and melt pressure, traditional decentralized PID (Proportional-Integral-Derivative) control is incapable of handling such processes if stricter product specifications are imposed or the material is changed from one batch to another. In this paper, new real-time energy monitoring methods have been introduced without the need to install power meters or develop data-driven models. The effects of process settings on energy efficiency and melt quality are then studied based on developed monitoring methods. Process variables include barrel heating temperature, water cooling temperature, and screw speed. Finally, a fuzzy logic controller is developed for a single screw extruder to achieve high melt quality. The resultant performance of the developed controller has shown it to be a satisfactory alternative to the expensive gear pump. Energy efficiency of the extruder can further be achieved by optimising the temperature settings. Experimental results from open-loop control and fuzzy control on a Killion 25 mm single screw extruder are presented to confirm the efficacy of the proposed approach. (C) 2013 Elsevier Ltd. All rights reserved.

There are great energy savings to be made by recycling aluminium; as little as 5% of the energy needed for primary aluminium production may be required. Striving to produce high quality aluminium castings requires knowledge of microstructural imperfections, which is extra important when casting recycled aluminium that generally contains higher levels of imperfections compared to primary aluminium. Imperfections include amongst others Si, Fe, and Mn as well as oxides. Si is needed for castability, but it may also initiate fracture. There are different types of Fe-rich intermetallics influencing properties of castings, generally in a negative direction. Oxides constitute cracks and they are elusive because they are difficult to quantify. This thesis aims to increase knowledge about imperfections in recycled aluminium castings originating from alloying elements and the melt. Experiments were performed in advanced laboratory equipment, including X-radiographic imaging during solidification and in-situ tensile testing in a scanning electron microscope. Experiments were also performed at industrial foundry facilities. The experiments showed that the nucleation temperature of primary α-Fe intermetallics increased with higher Fe, Mn, and Cr contents. Primary α-Fe are strongly suggested to nucleate on oxides and to grow in four basic morphologies. Lower nucleation frequency of α-Fe promoted faster growth and hopper crystals while higher nucleation frequency promoted slower growth rates and massive crystals. Results also showed that a decrease in the size of the eutectic Si and plate-like β-Fe intermetallics improved tensile properties, foremost the elongation to fracture. In β-Fe containing alloys the transversely oriented intermetallics initiated macrocracks that are potential fracture initiation sites. In alloys with primary α-Fe foremost clusters of intermetallics promoted macrocracks. In fatigue testing, a transition from β-Fe to α-Fe shifted the initiation sites from oxides and pores to the α-Fe, resulting in a decrease of fatigue strength. Oxides in Al-Si alloys continue to be elusive; no correlations between efforts to quantify the oxides and tensile properties could be observed. / Genom att återvinna aluminium kan stora energibesparingar göras eftersom återvinning kan förbruka så lite som 5% av den energi som behövs för produktion av primär aluminium. Vid gjutning av högkvalitativa aluminiumprodukter krävs förståelse för defekter i mikrostrukturen och denna kunskap är extra viktig vid användning av återvunnen aluminium, som i regel innehåller mer defekter än primär aluminium. Defekterna består bland annat av Si, Fe och Mn samt oxider. Si behövs för gjutbarhet men kan också initiera brott. Järnrika intermetaller kan ha olika morfologier som generellt påverkar gjutna komponenter negativt. Oxider, som kan utgöra sprickor, är gäckande då de är svåra att kvantifiera. Denna avhandlings syfte är att öka kunskapen om defekter i gjutna komponenter av återvunnen aluminium. Experiment utfördes med avancerad laborationsutrustning så som röntgenfotografering av prover under stelning och dragprovning i svepelektronmikroskop. Experiment utfördes också i industrimiljö. Experimenten visade att kärnbildningstemperaturen steg för primära α-Fe intermetaller med ökade andelar av Fe, Mn och Cr. Resultaten tyder starkt på att primär α-Fe kärnbildas på oxider och att de växer i fyra olika morfologier. Lägre kärnbildningstäthet av α-Fe främjade snabbare tillväxt av kristaller med håligheter men högre kärnbildningstäthet främjade långsammare tillväxt av massiva kristaller. Resultaten visade också att minskad storlek av eutektiskt Si och β-Fe intermetaller ledde till förbättring av dragprovsresultaten, främst brottförlängningen. I legeringar med β-Fe ledde transversellt orienterade intermetaller till makrosprickor vilka kan initiera brott. I legeringar med primär α-Fe var det främst kluster av intermetaller som orsakade makrosprickor. I utmattningsprovning orsakade modifiering av β-Fe till α-Fe förflyttning av sprickinitieringen från oxider och porer till α-Fe, vilket resulterade i en reducerad utmattningshållfasthet. Oxiderna i Al-Si-legeringar fortsätter att gäcka; ingen korrelation mellan försök att kvantifiera oxiderna och draghållfasthet kunde påvisas.