Spelling suggestions: "subject:"tet. coke - HDPE mix"" "subject:"tet. yoke - HDPE mix""
1 |
Fundamental investigation of slag/carbon interactions in electric arc furnace steelmaking processRahman, Muhammad Mahfuzur, Materials Science & Engineering, Faculty of Science, UNSW January 2010 (has links)
This work investigates the interactions of carbonaceous materials (metallurgical coke, natural graphite and HDPE/coke blends) with three EAF slags [FeO: 24% to 32%]. Experiments were conducted using the sessile drop technique (1500??C-1600??C) with off-gases (CO, CO2) measured using an IR analyzer; the wetting behaviour was determined from contact angle measurements. Estimation of slag foaming behaviour was determined from the droplet volume changes calculated using specialized software. At 1550??C, all slags were non-wetting with coke due to increased surface tension due to sulphur. At 1550??C, slag 1 was initially non-wetting on natural graphite due to gas entrapment in the slag droplet; the wetting improved after that. Other slags showed comparatively better wetting. At 1600??C, all slags were non-wetting with coke. Slags showed a shift from non-wetting to wetting behaviour with natural graphite. Slag/coke reactions produced high off-gases levels causing extensive FeO reduction; gas entrapment in the slag was poor (small volume droplets). Slag/natural graphite interactions revealed both slow gas generation rates and FeO reduction, and excellent gas entrapment (higher droplet volumes) with minor changes in slag properties due to low ash levels. The iron oxide reduction rates were determined to be 1.54x10-5 and 4.2x10-6 mol.cm-2/sec (Slag 1, 1550??C) for metallurgical coke and natural graphite respectively. Slag interactions with coke/HDPE blends showed increasing off-gas levels with increasing HDPE levels. Blend#3 produced the highest off-gas levels, extensive FeO reduction and displayed significantly higher slag foaming and better wetting compared to coke. Our line on trends compared well for slag/carbon interactions and resulted in deceased specific energy consumption and carbon usage and increased productivity. These findings have enhanced the possibility of utilizing polymeric wastes in blends with coke in EAF steelmaking for slag/carbon interactions.
|
2 |
Fundamental investigation of slag/carbon interactions in electric arc furnace steelmaking processRahman, Muhammad Mahfuzur, Materials Science & Engineering, Faculty of Science, UNSW January 2010 (has links)
This work investigates the interactions of carbonaceous materials (metallurgical coke, natural graphite and HDPE/coke blends) with three EAF slags [FeO: 24% to 32%]. Experiments were conducted using the sessile drop technique (1500??C-1600??C) with off-gases (CO, CO2) measured using an IR analyzer; the wetting behaviour was determined from contact angle measurements. Estimation of slag foaming behaviour was determined from the droplet volume changes calculated using specialized software. At 1550??C, all slags were non-wetting with coke due to increased surface tension due to sulphur. At 1550??C, slag 1 was initially non-wetting on natural graphite due to gas entrapment in the slag droplet; the wetting improved after that. Other slags showed comparatively better wetting. At 1600??C, all slags were non-wetting with coke. Slags showed a shift from non-wetting to wetting behaviour with natural graphite. Slag/coke reactions produced high off-gases levels causing extensive FeO reduction; gas entrapment in the slag was poor (small volume droplets). Slag/natural graphite interactions revealed both slow gas generation rates and FeO reduction, and excellent gas entrapment (higher droplet volumes) with minor changes in slag properties due to low ash levels. The iron oxide reduction rates were determined to be 1.54x10-5 and 4.2x10-6 mol.cm-2/sec (Slag 1, 1550??C) for metallurgical coke and natural graphite respectively. Slag interactions with coke/HDPE blends showed increasing off-gas levels with increasing HDPE levels. Blend#3 produced the highest off-gas levels, extensive FeO reduction and displayed significantly higher slag foaming and better wetting compared to coke. Our line on trends compared well for slag/carbon interactions and resulted in deceased specific energy consumption and carbon usage and increased productivity. These findings have enhanced the possibility of utilizing polymeric wastes in blends with coke in EAF steelmaking for slag/carbon interactions.
|
Page generated in 0.0807 seconds