No description available.

Rural electrification has long been the most important topic on the development agenda of many countries. The needs for power supplies to rural areas increased significantly in the past decades. Extending electricity grids to rural areas is of a very high initial cost and is not viable economically. Micro hydroelectric power plants provide a good economical solution, which is also environmentally very friendly. The current study concentrates on selecting and optimizing a suitable cross-flow micro-turbine to be used in micro hydroelectric power plants. Cross-flow turbines are in general of simple structure, low cost, easy to fabricate and of modest efficiency. The main purpose of the present work is to optimize the performance of a selected turbine by establishing the optimal turbine’s design parameters. A complete analysis of the internal flow, which is of turbulent, two-phase and three dimensional in nature, was undertaken by simulating it using various CFD simulation codes. This study reports on the flow simulation using ANSYS CFX with a two-phase flow model, water-air free surface model and shear stress transport (SST) turbulence model. Prediction velocity and pressure fields of inside the turbine are, subsequently, used to characterize the turbine performance for different geometric parameters including the number of runner blades, the angle of attack, the ratio of inner to outer diameter, the nozzle profile, the blade profile, the nozzle throat width, the nozzle to runner blades width and the runner blades width to outer runner diameter. The results revealed the highly complex nature of the flow and provided a very good insight to the flow structure and performance optimization parameters.

Hydro power can be defined as converting the energy of flowing water into useful mechanical power by a turbine or water wheel. A micro hydro system typically has an electrical generation capacity of less than 100 kilo watts. These systems are usually constructed to supply power to individuals or groups of individuals who are independent of the power supply grid. The scope of this project is to outline the principles of micro hydro and to document the design process of a micro hydro site. This will include the measurements, calculations, and methods performed in a feasibility study for a potential site. The desired outcome of the project is to develop a viable solution to gain energy independence at a remote site owned by the author.

Master of Science / Department of Electrical and Computer Engineering / Dwight D. Day / Micro-hydro turbines generate power for small villages and industries in Afghanistan. They usually produce less than 100 kW of power. Currently the flow into the turbine is controlled manually and the voltage is controlled automatically with an electronic load controller. Excess power not used by the village is dumped into a community water heater. For larger sites that have a reservoir and/or large variable load throughout the day and night, the turbine needs to be fitted with an automatic flow control system to conserve water in the reservoir or deal with the variable loads. Large turbines usually use hydraulic governors that automatically adjust the flow of water into the turbine. For micro-hydro sized plants this method would be too expensive and be difficult to build and maintain locally. For this reason, a 3 phase AC induction motor will be used to move the internal flow control valve of the turbine. Because a sudden change in load is possible (30 – 40%) for micro-hydro plants, the electronic load controller will also be needed to respond to quick changes in load so that the village voltage does not exceed 220V. This report documents the process of building a test system comprising of a dynamic resistive load, microcontroller controlled resistive load, a three phase AC generator and a DC Motor. Where the dynamic resistive load represents the load of the village, the computer controlled resistive load would represent the community water heater, the three phase AC generator represents the Generator on site and the DC Motor together with its DC input voltage would emulate the turbine and its water flow respectively. The DC input voltage would be also controlled with a PWM signal through a delay loop to represent the water gate delay effects on the turbine as close as possible. With this, it would be possible to completely build and test a control system that emulates the dynamics of a water turbine generator.

Master of Science / Department of Electrical and Computer Engineering / Anil Pahwa / In Afghanistan, electricity is mostly generated by hydroelectric, diesel and natural gas generators. A significant amount of electricity also is imported from neighboring countries. Accessibility of electricity is mostly limited to the capital and main towns. The government of Afghanistan and other development organizations, such as The United States Agency for International Development (USAID) and Deutsche Gesellschaft für Internationale Zusammenarbeit (German Agency for International Cooperation “GIZ”), are striving to develop accessibility of electricity to remote communities by supporting the local population of people to enhance living conditions. Although some of these remote communities are served by local diesel fuel generators for just a couple of hours during the night, still most communities do not have access to electricity and they are using wood and kerosene as major sources of energy in cooking, heating and lighting. For those remote communities who are served by local diesel fuel generators, the cost of electricity is much higher than from the national grid. On the other hand, grid extensions are too expensive and, in some cases, impossible for such communities because of the geographical features of Afghanistan. Afghanistan is a mountainous country which receives a significant amount of snow during the winter and once it melts the water runs into rivers, lakes and streams. Therefore mostly it does not face any shortage of running water during the year. Also Afghanistan has plentiful wind and solar energy. Therefore, small hydro-power, wind turbine and solar energy are attractive renewable energy sources for remote communities. The development of such a hybrid power system is a complex process and technical expertise is essential in design and construction phases. The main challenges are the high cost of civil works and equipment, technical expertise for design and construction and encouragement of local people for the support of the project. This report will give an insight into design, cost-effectiveness and feasibility of the system using HOMER in order to encourage private investors and local community people to take advantage of this potential available in Afghanistan and be convinced of the sustainability for investments in micro-hydropower, wind and solar.

This study focuses on the design, construction and operation of a distributed generation system based on micro-hydro technology. The project is sited in the Totara Valley, a small rural community approximately 70km from the Massey University, Turitea campus, Palmerston North. The Massey University Centre for Energy Research (MUCER) has a long history of renewable energy research within the Totara Valley community. This project complements these existing schemes and provides a foundation for future research into distributed generation technologies. The project encompasses the following objectives: - to gain practical experience in the design, engineering and implementation of a distributed generation system in rural New Zealand; - to evaluate contemporary micro-hydro technology and compare the performance of this equipment in a theoretical and practical context; - to identify barriers that hinder the widespread adoption of micro-hydro systems in rural New Zealand; - to develop a spreadsheet based life cycle costing tool. The results from this study demonstrate that economic considerations are the fundamental aspect to be considered when assessing the long-term viability of these projects. The viability of micro-hydro projects are primarily determined by four factors: - the volume and head (height) of water available above the turbine site; - the length and therefore the cost of the pipeline required for transporting water to the turbine; - the legal and administrative costs involved in obtaining a resource consent to maintain access to the water resources; - the prices received and paid for electricity. Considerable charges were payable to the local authority to secure and maintain the right to harness the water resources at this site. This cost contributed considerable risk to the project and creates a significant barrier to establishing similar systems at other sites. The reduction of resource consent charges to levels that fairly reflect the negligible environmental impacts of these projects would encourage the adoption of this technology and deliver benefits to rural New Zealand communities.

This study focuses on the design, construction and operation of a distributed generation system based on micro-hydro technology. The project is sited in the Totara Valley, a small rural community approximately 70km from the Massey University, Turitea campus, Palmerston North. The Massey University Centre for Energy Research (MUCER) has a long history of renewable energy research within the Totara Valley community. This project complements these existing schemes and provides a foundation for future research into distributed generation technologies. The project encompasses the following objectives: - to gain practical experience in the design, engineering and implementation of a distributed generation system in rural New Zealand; - to evaluate contemporary micro-hydro technology and compare the performance of this equipment in a theoretical and practical context; - to identify barriers that hinder the widespread adoption of micro-hydro systems in rural New Zealand; - to develop a spreadsheet based life cycle costing tool. The results from this study demonstrate that economic considerations are the fundamental aspect to be considered when assessing the long-term viability of these projects. The viability of micro-hydro projects are primarily determined by four factors: - the volume and head (height) of water available above the turbine site; - the length and therefore the cost of the pipeline required for transporting water to the turbine; - the legal and administrative costs involved in obtaining a resource consent to maintain access to the water resources; - the prices received and paid for electricity. Considerable charges were payable to the local authority to secure and maintain the right to harness the water resources at this site. This cost contributed considerable risk to the project and creates a significant barrier to establishing similar systems at other sites. The reduction of resource consent charges to levels that fairly reflect the negligible environmental impacts of these projects would encourage the adoption of this technology and deliver benefits to rural New Zealand communities.

This study focuses on the design, construction and operation of a distributed generation system based on micro-hydro technology. The project is sited in the Totara Valley, a small rural community approximately 70km from the Massey University, Turitea campus, Palmerston North. The Massey University Centre for Energy Research (MUCER) has a long history of renewable energy research within the Totara Valley community. This project complements these existing schemes and provides a foundation for future research into distributed generation technologies. The project encompasses the following objectives: - to gain practical experience in the design, engineering and implementation of a distributed generation system in rural New Zealand; - to evaluate contemporary micro-hydro technology and compare the performance of this equipment in a theoretical and practical context; - to identify barriers that hinder the widespread adoption of micro-hydro systems in rural New Zealand; - to develop a spreadsheet based life cycle costing tool. The results from this study demonstrate that economic considerations are the fundamental aspect to be considered when assessing the long-term viability of these projects. The viability of micro-hydro projects are primarily determined by four factors: - the volume and head (height) of water available above the turbine site; - the length and therefore the cost of the pipeline required for transporting water to the turbine; - the legal and administrative costs involved in obtaining a resource consent to maintain access to the water resources; - the prices received and paid for electricity. Considerable charges were payable to the local authority to secure and maintain the right to harness the water resources at this site. This cost contributed considerable risk to the project and creates a significant barrier to establishing similar systems at other sites. The reduction of resource consent charges to levels that fairly reflect the negligible environmental impacts of these projects would encourage the adoption of this technology and deliver benefits to rural New Zealand communities.

This study focuses on the design, construction and operation of a distributed generation system based on micro-hydro technology. The project is sited in the Totara Valley, a small rural community approximately 70km from the Massey University, Turitea campus, Palmerston North. The Massey University Centre for Energy Research (MUCER) has a long history of renewable energy research within the Totara Valley community. This project complements these existing schemes and provides a foundation for future research into distributed generation technologies. The project encompasses the following objectives: - to gain practical experience in the design, engineering and implementation of a distributed generation system in rural New Zealand; - to evaluate contemporary micro-hydro technology and compare the performance of this equipment in a theoretical and practical context; - to identify barriers that hinder the widespread adoption of micro-hydro systems in rural New Zealand; - to develop a spreadsheet based life cycle costing tool. The results from this study demonstrate that economic considerations are the fundamental aspect to be considered when assessing the long-term viability of these projects. The viability of micro-hydro projects are primarily determined by four factors: - the volume and head (height) of water available above the turbine site; - the length and therefore the cost of the pipeline required for transporting water to the turbine; - the legal and administrative costs involved in obtaining a resource consent to maintain access to the water resources; - the prices received and paid for electricity. Considerable charges were payable to the local authority to secure and maintain the right to harness the water resources at this site. This cost contributed considerable risk to the project and creates a significant barrier to establishing similar systems at other sites. The reduction of resource consent charges to levels that fairly reflect the negligible environmental impacts of these projects would encourage the adoption of this technology and deliver benefits to rural New Zealand communities.

This study focuses on the design, construction and operation of a distributed generation system based on micro-hydro technology. The project is sited in the Totara Valley, a small rural community approximately 70km from the Massey University, Turitea campus, Palmerston North. The Massey University Centre for Energy Research (MUCER) has a long history of renewable energy research within the Totara Valley community. This project complements these existing schemes and provides a foundation for future research into distributed generation technologies. The project encompasses the following objectives: - to gain practical experience in the design, engineering and implementation of a distributed generation system in rural New Zealand; - to evaluate contemporary micro-hydro technology and compare the performance of this equipment in a theoretical and practical context; - to identify barriers that hinder the widespread adoption of micro-hydro systems in rural New Zealand; - to develop a spreadsheet based life cycle costing tool. The results from this study demonstrate that economic considerations are the fundamental aspect to be considered when assessing the long-term viability of these projects. The viability of micro-hydro projects are primarily determined by four factors: - the volume and head (height) of water available above the turbine site; - the length and therefore the cost of the pipeline required for transporting water to the turbine; - the legal and administrative costs involved in obtaining a resource consent to maintain access to the water resources; - the prices received and paid for electricity. Considerable charges were payable to the local authority to secure and maintain the right to harness the water resources at this site. This cost contributed considerable risk to the project and creates a significant barrier to establishing similar systems at other sites. The reduction of resource consent charges to levels that fairly reflect the negligible environmental impacts of these projects would encourage the adoption of this technology and deliver benefits to rural New Zealand communities.