Aluminium alloys with Si as the major alloying element form a class of material providing the most significant part of all casting manufactured materials. These alloys have a wide range of applications in the automotive and aerospace industries due to an excellent combination of castability and mechanical properties, as well as good corrosion resistance and wear resistivity. Additions of minor alloying elements such as Cu and Mg improve the mechanical properties and make the alloy responsive to heat treatment. The aim of this work is studying the role of size and morphology of microstructural constituents (e.g SDAS, Si-particles and intermetalics) on mechanical properties of Al-Si based casting alloy at room temperatures up to 500 ºC. The cooling rate controls the secondary dendrite arm spacing (SDAS), size and distribution of secondary phases. As SDAS becomes smaller, porosity and second phase constituents are dispersed more finely and evenly. This refinement of the microstructure leads to substantial improvement in tensile properties (e.g. Rm and εF). Addition of about 280 ppm Sr to EN AC- 46000 alloy yields fully modified Si-particles (from coarse plates to fine fibres) regardless of the cooling conditions. Depression in eutectic growth temperature as a result of Sr addition was found to be strongly correlated to the level of modification irrespective of coarseness of microstructure. Modification treatment can improve elongation to failure to a great extent as long as the intermetallic compounds are refined in size. Above 300 ºC, tensile strength, Rp0.2 and Rm, of EN AC-46000 alloys are dramatically degraded while the ductility was increased. The fine microstructure (SDAS 10 μm) has superior Rm and ductility compared to the coarse microstructure (SDAS 25 μm) at all test temperature (from room to 500 ºC). Concentration of solutes (e.g. Cu and Mg) in the dendrites increases at 300 ºC and above where Rp0.2 monotonically decreased. The brittleness of the alloy below 300 ºC was related to accumulation of a high volume fraction damaged particles such as Cu- Fe-bearing phases and Si-particles. The initiation rate of damage in the coarse particles was significantly higher, which enhances the probability of failure and decreasing both Rm and εF compared to the fine microstructure. A physically-based model was adapted, improved and validated in order to predict the flow stress behaviour of EN AC- 46000 cast alloys at room temperature up to 400 ºC for various microstructures. The temperature dependant variables of the model were quite well correlated to the underlying physics of the material

Magnesium and magnesium alloys are used in a wide variety of structural applications including automotive, aerospace, hand tools and electronic industries thanks to their light weight, high specific strength, adequate corrosion resistance and good castability. Al and Zn are the primary alloying elements in commercial Mg alloys and commonly used in automotive industries. AZ91 is one of the most popular Mg alloys containing 9% Al and 1% Zn. Hence, lots of research have been done during last decades on AZ91D. However, the existing data concerning mechanical properties and microstructural features showed large scatter and is even contradictory. This work focused on the correlation between the microstructure and the mechanical properties of as-cast AZ91 alloy. An exhaustive characterization of the grain size, secondary dendrite arm spacing (SDAS) distribution, and fraction of Mg17Al12 using optical and electron backscattered diffraction (EBSD) was performed. These microstructural parameters were correlated to offset yield point (Rp0.2), fracture strength and elongation to fracture. It was understood that the intermetallic phase, Mg17Al12, plays an important role in determining the mechanical and physical properties of the alloy at temperature range from room temperature up to 190oC. It was realized that by increasing the Mg17Al12 content above 11% a network of intermetallic may form. During deformation this rigid network should break before any plastic deformation happen. Hence, increase in Mg17Al12 content resulted in an increase in offset yield point. The presence of this network was supported by study of thermal expansion behaviour of the alloy containing different amount of Mg17Al12. A physically-based model was adapted and validated in order to predict the flow stress behaviour of as-cast AZ91D at room temperature up to 190ºC for various microstructures. The model was based on dislocation glide and climb in a single-phase (matrix) material containing reinforcing particles. The temperature dependant variables of the model were quite well correlated to the underlying physics of the material.