Ti-5Al-5Mo-5V-3Cr (Ti-5553), a relatively new generation beta titanium alloy has the advantage of high strength. It is a current generation alloy used in landing gear. Currently, landing gear components are large scale and processed through forging, followed by complex heat treatments. HIPping (hot isostatic pressing) is an alternative way to process this alloy. In this project, work was carried out on investigating microstructures and mechanical properties of HIPped Ti-5553 alloy. During comparisons on fracture toughness of different types of specimens, specimens are first heat treated to a similar strength level. And fracture toughness values are calculated at the same strength level circumstance. Various microstructures are obtained through different heat treatments. Different microstructures can be achieved through specified treated temperature/ time and quenching methods. Results show that larger grain size and coarser intergranular lath-like grain boundary alpha can improve the fracture toughness. One shell-like microstructure is obtained through different heat treatment conditions. Mechanical test was carried out on this kind of microstructure and compared to normal beta annealed microstructures. To investigate the influence of microstructure on fracture toughness, techniques including optical microscope (OM), scanning electron microscope (SEM), and confocal laser scanning microscope have been used.

No description available.

The research outlined in this thesis is concerned with the environmental aspects of groundwater re-establishment as a consequence of surface mining. No principal effects which have been identified as being detrimental to the restored land area are as follows; i). The vertical and horizontal displacements of backfill materials following restoration, and ii). The pollution of groundwater from contact with weathered rockfill materials. The research into settlement has attempted to classify the types of movement which may occur within a backfill mass, in particular the differential movements which are of great importance to the stability of proposed structures or surface drainage. The field results from 10 opencast mine sites are presented, 3 of which were instrumented for detailed field investigations. It has been shown that backfill movements do not necessarily show similar trends under similar conditions, and reasons for this are proposed. A variety of instrumentation schemes have been devised to examine backfill displacements, both vertically and horizontally. Permeability testing has been conducted at different horizons the backfill mass in order to locate the zones of collapse settlement due to groundwater recovery. A critical review of the instrumentation utilised in the investigations is presented, with suggestions for improvement. Investigations into groundwater pollution have been devoted to examining the qualities of groundwater flowing into British surface mines and evaluating its likely reactions with fill materials. An insight into general groundwater pollution and treatment techniques is presented together with a critical analysis of their applicability, to British conditions. An investigation into water qualities in each of the six geographical regions of the opencast mining industry of Great Britain is detailed. Finally some suggestions for future research areas are indicated.

MgH2 is considered to be one of the most promising options for a solid state hydrogen storage material. For practical use it is still imperative to find a convenient means of overcoming its slow kinetics and high stability. In this investigation, a range of binary and ternary metal oxides of aluminium, silicon, titanium, and zirconium, as well as Pd-modified Ti02 samples, were prepared and characterised. The prepared oxides were ball milled with MgH2, and the hydrogen sorption behaviour of the ball milled mixtures was investigated using DSC-TGA-MSS, Sieverts and IGA. Thermodynamic parameters including enthalpies and entropies of hydrogen desorption were determined from experimental data, and activation energy calculations along with modelling of the kinetics were used to understand the mechanism and rate-limiting step of dehydrogenation. Oxide components, calcination temperature, and surface area were found to have a significant impact on the hydrogen sorption behaviour of MgH2 in the ball milled mixtures. Of the prepared binary and ternary oxides, Ti02 and mixed oxides with a Ti02 component were found to lower the dehydrogenation onset temperature by as much as 100°C, while additions of Pd-modified Ti02 resulted in the lowest dehydrogenation onset temperature of 205°C, compared to 360°C for ball milled MgH2. In addition, rates of hydrogen desorption and absorption were significantly increased as a result of the Ti02 and Ti02 - Pd additives. Dehydrogenation of 90 % of the full H2 capacity took 6 min at 300°C, compared to 230 min for milled MgH2 at 350°C. It was found that a reduction of the Ti02 oxide resulted in the active species responsible for the enhanced dehydrogenation behaviour. Through analysis of the reaction kinetics, the mechanism of dehydrogenation was found to change from a surface controlled, contracting volume model for ball milled MgH2 to one of a Johnson-Mehl-Avrami model of two - dimensional nucleation and growth upon addition of Ti02 and Ti02 - Pd.

The development of electronic surveying instruments, such as electronic theodolites, and concurrent advances in computer technology, has revolutionised engineering surveying; one of the more recent examples being the introduction of Electronic Theodolite Intersection Systems (ETISs). An ETIS consists of two or more electronic theodolites and a computer, with peripheral hardware and suitable software. The theoretical principles on which they are based have been known for a long time, but intersection has seldom been used as a method of measurement. The main reasons for its re-evaluation were the introduction of one-second electronic theodolites and the ability to interface these on-line to a computer. The last decade has seen the development of several commercially available systems and probably even more in-house developed systems. Such systems are capable of performing real-time, non-contact, three-dimensional coordinate determination to a high accuracy, enabling their use in a wide variety of applications. This thesis details all aspects of ETISs. Initially, the theoretical principles on which the systems are based are developed. The components of a system are then detailed and a review of current commercially available systems and their applications is given. The thesis then concentrates on the development of an ETIS by the author and details its' application in both industrial measurement and deformation monitoring. Finally, the thesis concludes with a discussion on the factors affecting the accuracies attainable with ETISs.

No description available.

The key controlling factor in the effective energy conversion of coal to combustible gases during the UCG process is the behaviour of the pyrolysed char in the reduction zone of the UCG cavity, which has not been published in available academic literature. This study investigates the impact of the operating parameters during the reduction zone of UCG using a bespoke high pressure high temperature rig which was developed as part of this research work. This rig, operating at temperatures of up to 900 oC and at pressures up to 5.0 MPa, simulates the UCG process including each UCG zone individually for a broad range of underground conditions to a depth of 500 m. Carbon dioxide and steam were used as the primary reductants with char derived from dry steam coal and anthracite sample. Carbon dioxide and steam were injected at a variety of pressures and temperatures, plus at a range of relative H2O/CO2 proportions. The composition of the resulting product gas of both coals was measured and subsequently used to calculate carbon conversion (X), carbon conversion of combustible gases ( ), cold gas efficiency (CGE) and low heating value (LHV) of the product gas. Optimal operating conditions were determined for the dry steam coal and anthracite that produced the best gas composition both at atmospheric and elevated pressure and are unique for each UCG system. A shrinking core model was employed to describe the behaviour of the pyrolised char to determine the activation energy and pre-exponential factor at atmospheric pressure for both coals. The evolution of the volatile matter of both coals and its contribution to the overall UCG performance was also determined. An optimum H2O/CO2 ratio was determined for both coals which enhanced the gasification rate of both coal chars up to the ratio of 2:1, above this ratio the effect saturated for both coals. It was shown that pressure increases the reduction-gasification process of the chars which suggests that there is an optimum operating pressure which produces a peak in carbon conversion, CGE and LHV for the product gas over the conditions tested that differs for each coal. Therefore UCG projects aiming at reaching higher pressures will not achieve an increase in the output, unless there are some new effects occurring above 4.0 MPa. Pressure enhances the gas solid reactions and almost doubles the max carbon conversion ( of combustible gases achieved at elevated pressure compared to that at atmospheric pressure. A shrinking core model was modified to take into account the effect of total pressure to the gasification rate of dry steam coal at 900 oC and pressures ranging from 0.7 to 1.65 MPa. Reaction constants for various pressures at 900 oC were determined for both coal chars. Analysis of data shown that typical UCG operations on low rank coals provides a combustible product gas that relies heavily on releasing the volatile matter from the coal and does not depend on the carbon conversion of char to gas which justifies the high CGE and LHV of the product gas found in the field trials. It was found that carbon conversion X is not significantly affected by the type of coal and that the carbon converted during UCG is between approximately 45% for high rank coals up to 55% for low rank coals. Experimental results were used to calculate the output, size and UCG model of a potential power plant which produced realistic solutions and proves that high rank coals can be suitable for UCG projects. Anthracite can produce almost the same amount of combustible gases as the dry steam coal operating under specific conditions but with a lower CGE and LHV which suggests that anthracite may be found to be more suitable for producing hydrocarbons with UCG than energy.

In this thesis the influence of microstructure on fracture toughness is investigated for two different medium/high strength Al-alloys for aerospace application. In weldable AA6156 (Al-Mg-Si-Cu) alloy sheet, the quench sensitivity in toughness is assessed via enhanced Kahn tear tests. Toughness was seen to be reduced for both 60°C water quenched and air cooled materials cf. 20°C water quench material. Fractography via scanning electron microscopy (SEM) and synchrotron radiation computed tomography (SRCT), as well as Differential Scanning Calorimetry (DSC) and Transmission Electron Microscopy (TEM) studies, have clarified the mechanisms of the quench sensitivity with respect to toughness. Both the coverage of grain boundary decoration and precipitate free zone (PFZ) width increase with reduced quench rates. The failure morphology of the air cooled material appears consistent with classical intergranular ductile failure. Coarse voiding and shear decohesion was prevalent in 20°C water quenched material (depending on local triaxiality), whilst the 60°C water quenched material showed a mixture of transgranular and intergranular fracture modes. The experimental toughness trends are compared to models in the literature and a simple new model is suggested. Fracture toughness anisotropy of AA2139 (Al-Cu-Mg), a candidate alloy for age forming, in T351 and T8 conditions has been investigated via mechanical testing of smooth and notched specimens of different geometries, loaded in the rolling direction (L) or in the transverse direction (T). Fracture mechanisms are again investigated via SEM and SRCT. Fracture toughness is seen to be anisotropic for both heat treatment conditions tested, but is substantially reduced for the T8 condition compared to the T351. Contributions to failure behaviour have been identified with: (i) anisotropic initial void shape and growth, (ii) plastic behaviour, including isotropic/kinematic hardening and plastic anisotropy, and (iii) nucleation at a 2nd population of 2nd phase particles leading to coalescence via narrow crack regions. SRCT analysis of arrested cracks revealed alignment of voids in the crack during propagation in the rolling direction, resulting in shorter intervoid ligaments than for crack propagation in the transverse direction. Coalescence through shear decohesion in the crack initiation and propagation region was found indicating the necessity to investigate and account for this mechanism. A model based in part on the Gurson-Tvergaard- Needleman approach is constructed to describe and predict deformation behaviour, crack propagation and, in particular, toughness anisotropy. Model parameters are fitted using microstructural data and data on deformation and crack propagation for a range of small test samples. The model accounts for the material features found in the experimental study and its transferability has been shown by simulating tests of large M(T) samples showing strong fracture toughness anisotropy. A parametric study shows that nucleation of small voids at different strains for different loading directions is crucial for a correct model of toughness anisotropy; the combined effects of kinematic hardening and void growth anisotropy can not fully describe fracture toughness anisotropy.

The acoustic remote sensing of subsea gas leakage, applied to the monitoring of underwater gas discharges from anthropogenic and natural sources, is becoming increasingly important. First, as the oil and gas industry is facing increasing regulation, there is a need to put more control in the industrial process and to assess the impact on the marine environment. The applications are diverse, including: early warnings of "blow-out" from offshore installations, detection of leaks from underwater gas pipelines, gas leakage detection from Carbon and Capture and Storage facilities (a process aimed at mitigating the release of large quantities of CO2 in the atmosphere), and seabed monitoring. Second, this technology has a role to play in oceanography for a better understanding of natural occurrences of gas release from the sea floor such as methane seeps. This is of major importance for the assessment of the exchange of gas between the ocean and the atmosphere with application to global warming. All those phenomena involve the formation and release of bubbles of different sizes. These are strong sources and scatterers of sound. Within this context, this thesis draws on a two part study. The first part experimentally addresses the accuracy of a passive acoustic inversion method for the quantification of gas release. Such a technique offers the advantage of lower power requirements for long term monitoring. It is common practice for researchers to identify single bubble injection events from time histories or time frequency representations of hydrophone data, and infer bubble sizes from the centre frequency of the emission. This is well suited for gas release at a low flow rate, involving solitary bubble release. However, for larger events, with overlapping of bubble acoustic emissions, the inability to discriminate each individual bubble injection events makes this approach inappropriate. Using an inverse method based on the spectrum of the acoustic emissions allows quantification of such releases with good accuracy. The inverse scheme is tested using data collected in a large test tank and data collected at sea during the QICS (Quantifying Impacts of Carbon Storage) project. The second part of the thesis addresses the problem of quantifying gas releases using active acoustics. Single beam echosounders are commonly used instruments in fisheries acoustics. When investigating gas release from the seafloor, they are frequently employed to study the spatial distribution of the gas releases. However, few studies make use of these data to quantify the amount of gas being released. Here, using the common multi-frequency ability of these systems, an inverse method aimed at determining gas volumes is developed. This is tested against simulated data and the method shows good performances in scenarios with limited data sets (data collected at limited number of frequencies). Then, using data collected at sea from methane seeps to the west of Svalbard (from two research cruises), the method is applied and compared to independent measurements of gas fluxes.

Application prospects in the automotive industry have led to increasing studies on Al-Mg- Cu-Si alloys. In this thesis, nine Al-(1-3)Mg-(0-0.4)Cu-0.15Si-0.25Mn (in wt%) alloys with potential applications in packaging and automotive industries have been investigated. By means of mechanical testing, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM), several mechanisms was identified that influence the final strength of cold rolled alloys during ageing: solid solution, work hardening, recovery and precipitation. Microstructure analyses revealed the formation of undissolved particles consuming the small Si addition, which influences age hardening behaviour of the alloys. Tensile testing was performed to evaluate the strength and work hardening. The integrated experimental results showed that for cold worked samples, b² (Mg2Si) contributes to age hardening of Cu-free alloys, whilst both b² and S (Al2CuMg) contribute to that of Cu-containing alloys. According to the experimental findings, a yield strength model has been developed to elucidate the relation between processing and the final strength. It consists of three main components: i) dissolution of intermetallic phase Mg2Si; ii) precipitation of two strengthening phases b² and S; iii) strengthening contributions from solution strengthening, dislocation strengthening and precipitation hardening due to the strengthening phases. The model was calibrated and tested using separate tensile data and was applied to predict the yield strength evolution of cold worked samples during ageing. An accuracy of 8.6 MPa (about 4% of the total range of strengths) has been achieved. Based on the analysis of the relation of work hardening with cold work, composition and ageing time, three primary findings were obtained: i) cold worked samples usually have the lowest work hardening rate (WHR); ii) WHR increases after 30-minute ageing due to recovery and iii) WHR increases with decreasing level of cold work and increasing Mg and Cu contents. Work hardening models based on the Kocks-Mecking (KM) model and the Kocks-Mecking-Estrin (KME) model have been utilized to explain the main trends. The modelling results showed that the KM model is able to predict the work hardening behaviour of cold worked samples reasonably well. However, the KME model is insufficient to fully describe that of cold-worked-and-aged samples.